Single Line Descriptions - Nidec SI-Encoder V2 User Manual

Safety information Introduction
6.2

Single line descriptions

Parameter
mm.001 Module ID
mm.002 Firmware Version
mm.022 Active alarm
mm.024 Module Temperature
mm.027 Speed Feedback
mm.028 Revolution Counter
mm.029 Position
mm.030 Fine Position
mm.033 Turn Bits
mm.034 Lines Per Revolution
mm.036 Supply Voltage
mm.038 Device type
mm.039 Termination Select
mm.040 Error Detection Level
mm.041 Auto configuration Select
mm.042 Feedback Filter
mm.043 Maximum Reference
mm.044 Reference Scaling
mm.045 Reference
mm.046 Reference Destination
mm.049 Additional Power up Delay
mm.050 Position Feedback Lock
mm.056 Feedback Reverse
mm.057 Normalisation Turns
mm.058 Normalised Position
mm.067 User Comms Enable
mm.068 User Comms Transmit Register
mm.069 User Comms Receive Register
mm.070 Position Feedback Signals
mm.074 Additional Configuration
mm.075 Encoder Initialisation Mode
mm.076 Position Feedback Initialised
mm.101 Freeze Mode
mm.103 Normalised Freeze Position
mm.104 Freeze Flag
mm.113 Freeze Input State
mm.114 Freeze Sensor Delay
RW Read / Write
Num Number parameter
NC Non-copyable
14
Mechanical Installation Electrical Installation
Range
0 to 999
0 to 99999999
None (0), Low Battery (1)
-50 to 175 °C
±50000.0
0 to 65535
0 to 65535
0 to 65535
0 to 16
1 to 100000
5 V (0), 8 V (1), 15 V (2)
AB (0), SMART ABS (1),
Sankyo (2)
0 to 1
0000000 to 1111111
Disabled (0), Full (1),
Partial (2)
Disabled (0), 1 ms (1), 2 ms (2),
4 ms (3), 8 ms (4), 16 ms (5)
0 to 50000
0.000 to 4.000
±100.0 %
0.000 to 59.999
0.0 to 25.0
Off (0) or On (1)
Off (0) or On (1)
0 to 16
-2147483648 to 2147483647
Off (0) or On (1)
0 to 65535
0 to 65535
000000000 to 111111111
0 to 123
No Error Reset (0),
Error Reset Only (1), Multi turn
Reset (2), Position Reset (3)
Off (0) or On (1)
Rising 1st (0), Falling 1st (1),
Rising all (2), Falling all (3)
-2147483648 to 2147483647
Off (0) or On (1)
Off (0) or On (1)
0.0 to 250.0 µs
RO Read-only
Bin Binary parameter
PT Protected
Getting Started
Default
105
16
4096
5 V (0)
AB (0)
1
1100111
Full (1)
Disabled (0)
3000
1.000
0.000
0.0 s
Off (0)
Off (0)
16
Off (0)
0
0
1
Rising 1st (0)
0 µs
Bit Bit parameter
DE Destination
FI Filtered
Parameters Diagnostics
Type
RO Num ND NC PT
RO Num ND NC PT
RO Txt ND NC PT
RO Num ND NC PT
RO Num ND NC PT
RO Num ND NC PT
RO Num ND NC PT
RO Num ND NC PT
RW Num
RW Num
RW Txt
RW Txt
RW Num
RW Bin
RW Txt
RW Txt
RW Num
RW Num
RO Num ND NC PT
RW Num DE PT
RW Num
RW Bit
RW Bit
RW Num
RO Num ND NC PT
RW Bit NC PT
RW Num NC PT
RW Num NC PT
RO Bin ND NC PT
RW Num
RW Txt ND NC PT
RO Bit ND NC PT
RW Txt
RO Num ND NC PT
RW Bit ND NC PT
RO Bit ND NC PT
RW Num
Txt Text String
ND No default value
US User save
SI-Encoder V2 User Guide
FI
US
US
US
US
US
US
US
US
US
US
FI
US
US
US
US
US
US
US
US