Advertisement
Service Code
Reason
Family
(Platform specific)
80
Auto Door Opener malfunction
Auto Door Opener timeout warning
Water Reuse Valve warning
90
Checksum mcf
Checksum ccf
Checksum UIdata
UI data version mismatch
UI data checksum mismatch
B0 (H0)
BDIVA2, PB100
Turbidity sensor problem
before P100R230,
PB200 and PB300
BPB100 after
Turbidity
sensor
P100R230, PB101
unknown error
and PB150
PB100 after
lose contact with the turbidity
P100R230, PB101
sensor
and PB150
PB100 after
sensor
not
enough
P100R230, PB101
calibration
and PB150
PB100 after
sensor out of range calibration
P100R230, PB101
and PB150
PB100 after
sensor too noisy calibration
P100R230, PB101
and PB150
C0
No user interface detected
Macs – bus communication
Adsi – communication to ui
Motor control board comm
D0
Tacho problem
Tacho critical
E0
Flow control positioning
F0
Sw fill limit reached
SW Safety level reached
Technical Support – A.R.
Alarm Codes
Type
User
visible
abort
Yes
warning
No
warning
No
inactive
No
inactive
No
inactive
No
warning
No
warning
No
Please OBSERVE that iBx family has different meaning depending on PBs and PB firmware versions
warning
No
calibration
warning
No
warning
No
power
warning
No
warning
No
warning
No
stop
No
stop
Yes
stop
Yes
stop
Yes
warning
No
warning
No
warning
No
Warning
No
stop
Yes
User
failure
indication
code read
i80
i80
Cycle will be terminated and electronic switched to reset on-condition
Nothing
i81
Auto Door Opener tries to recover. If that fails, the cycle continues without
Nothing
i82
Nothing
i91
Nothing
i92
Nothing
i93
Nothing
i94
Nothing
i95
Nothing
ib0 (iH0)
Nothing
ib0 (iH0)
Cycle continues as though the dirt value to be considered is high
Nothing
ib1 (iH1)
Cycle continues as though the dirt value to be considered is high
Nothing
ib2 (iH2)
Cycle continues as though the dirt value to be considered is high
Nothing
ib3 (iH3)
Cycle continues as though the dirt value to be considered is high
Nothing
ib4 (iH4)
Cycle continues as though the dirt value to be considered is high
Nothing
ic0
Cycle stop and continuous automatic if problem solved
iC1
ic1
Macs low level communication - Cycle stop and continuous automatic if
iC2
ic2
Cycle stop and continuous automatic if problem solved
iC3
ic3
Command level communication - Cycle stop and continuous automatic if
Nothing
id0
Heating off up to end of cycle – motor to full speed – rta off
Nothing
id1
Heating off up to problem is solved – full speed – rta off
Nothing
iE0
Nothing
iF0
No further water load up to timer reset – rta off – cycle continues up to end of
iF1
iF1
Cycle stop and continuous automatic if problem solved
599 79 76 - 54 Rev 2
Action in case of failure happens
auto door opener
Cycle continues regardless the error
Electronic functionality blocked – all off
Electronic functionality blocked – all off
Electronic functionality blocked – all off
No update of UI configuration data is possible
No update of UI configuration data is possible
Turbidity flag set – cycle continuous
problem solved
problem solved
Heating element will be switched off
cycle – is power fail saved
User Indication
before March
2017
i80
Nothing
Nothing
Nothing
Nothing
Nothing
Nothing
Nothing
Nothing
Nothing
Nothing
Nothing
Nothing
Nothing
Nothing
iC0
iC0
iC0
Nothing
Nothing
Nothing
Nothing
iF0
4
Chapter
Advertisement
