Advertisement
Service Code
Reason
Family
(Platform specific)
00
Zero cross or low voltage
10
Fill_D – static fill level
Fill – re-fill level
20
Draining problem
30
Aqua Control
40
Analogue pressure
no signal
Pressure Sensor Calibration
signal too noisy
Analogue pressure
signal too high
Analogue pressure
signal too low
Pressure Sensor Calibration
signal too low
Pressure Sensor Calibration
signal too high
50
AC Wash pump tsc
WP BLDC over current HW
WP BLDC over current SW
WP BLDC motor not following
BLDC under voltage
BLDC over voltage
PB100 only
DP ADC fault
DIVA2 only
DCLink plausibility error
WP BLDC motor not connected
WP BLDC ADC fault
DIVA2 only
WP BLDC over temp
PB100 only
WP/DP BLDC overload
PB100 only
WP/DP current plausibility
PB100 only
DP BLDC over current HW
PB100 only
DP BLDC over current SW
PB100 only
DP BLDC motor not following
PB100 only
DP BLDC motor not connected
Technical Support – A.R.
Alarm Codes
Type
User
User
visible
indication
stop
No
Nothing
ack
Yes
i10
ack
Yes
i11
i20
ack
Yes
stop
Yes
i30
abort
Yes
ii41
warning
No
Nothing
abort
Yes
i43
abort
Yes
i44
warning
No
Nothing
warning
No
Nothing
i51
abort
Yes
i52
abort
Yes
i53
abort
Yes
abort
Yes
i54
stop
Yes
i55
stop
Yes
i56
abort
Yes
i57
Please OBSERVE that i57 has different meaning depending on platform
abort
Yes
i57
abort
Yes
i58
abort
Yes
i59
stop
Yes
i5A
Please OBSERVE that i5A has different meaning depending on platform
abort
Yes
i5A
abort
Yes
i5b (i5H)
i5C
abort
Yes
i5d
abort
Yes
i5E
abort
Yes
abort
Yes
i5F
599 79 76 - 54 Rev 2
failure
Action in case of failure happens
code read
i00
User interface off & remaining time adaptation off
i10
Cycle pause and request to user to confirm to re-start
i11
Cycle pause and request to user to confirm to restart
i20
Cycle pause and request to user to confirm to re-start
i30
Cycle stop and continuous automatically after problem solved – rta off
i41
Cycle will be terminated, electronic stop after on/off or failure solved
electronic will switched to reset on-condition
i42
Old calibration will be used, cycle continues
i43
Cycle will be terminated, electronic stop after on/off or failure solved
electronic will switched to reset on-condition
i44
Cycle will be terminated, electronic stop after on/off or failure solved
electronic will switched to reset on-condition
i45
Old calibration will be used, cycle continues
i46
Old calibration will be used, cycle continues
i51
Cycle will be terminated and electronic switched to reset on-condition
i52
Cycle will be terminated and electronic switched to reset on-condition
i53
Cycle will be terminated and electronic switched to reset on-condition
i54
Cycle will be terminated and electronic switched to reset on-condition
i55
Cycle stop and continuous automatically after probl. Solved – rta off
i56
Cycle stop and continuous automatically after probl. Solved – rta off
i57
Cycle will be terminated and electronic switched to reset on-condition
i57
Cycle will be terminated and electronic switched to reset on-condition
i58
Cycle will be terminated and electronic switched to reset on-condition
i59
Cycle will be terminated and electronic switched to reset on-condition
i5A
Cycle stop and continuous automatically after problem solved – rta off
i5A
Cycle will be terminated and electronic switched to reset on-condition
i5b (i5H)
Cycle will be terminated and electronic switched to reset on-condition
i5C
Cycle will be terminated and electronic switched to reset on-condition
i5d
Cycle will be terminated and electronic switched to reset on-condition
i5E
Cycle will be terminated and electronic switched to reset on-condition
i5F
Cycle will be terminated and electronic switched to reset on-condition
User Indication
before March
2017
Nothing
i10
i10
i20
i30
i40
Nothing
i40
i40
Nothing
Nothing
i50
i50
i50
i50
i50
i50
i50
i50
i50
i50
i50
i50
i50
i50
i50
i50
i50
4
Chapter
Advertisement
