ABB CBV-2U4-3T User Manual page 69

CBV-2U4-3T(-N) |
POINT SETPOINT OBJECTNAME
BLOCK
174 Yes FanHeatMaxMan (D174)
175 Yes FanStandbyMan (D175)
DO13RemoteCmd (D177)
177 Yes
178 Yes EnableManualHeatCmd (D178)
179 Yes EnableManualCoolCmd (D179)
180 No HeatModeSts
181 No CoolModeSts
184 Yes OccCmd (D184)
185 Yes StandbyCmd (D185)
OccModeSts (D186)
186 No
187 No StandbyModeSts (D187)
188 No OccSensorEffCmdOnBoardSwitch
(D188)
191 Yes DampOpenMan (D191)
192 Yes DampCloseMan (D192)
193 Yes DampMaxMan (D193)
194 Yes DampMinMan (D194)
199 Yes FireStopCmd (D199)
KFactSelect (D204)
204 Yes
208 No LoadShedEffCmd (D208)
210 Yes FanHeatMinMan (D210)
211 Yes LoadShedEnable (D211)
213 Yes Purge (D213)
222 No OverrideStatus_Outputs (D222)
223 No ManualStatus_Application (D223)
224 No OverrideStatus_Inputs (D224)
225 Yes DamperAdaption(D225)
CBV-2U4-3T ONLY
226 PurgeEffCmd (D226)
No
230 Yes DampReverse (D230)
231 Yes EnaUnoccCool (D231)
232 No IO_Application_Status (D232)
235 No UI04DigitalStatusHost (D235)
©ABB 2022 All Rights Reserved.
Subject to change without notice
WWW.CYLON.COM
Appendix : List of CBV-2U4-3T(-N) points
DESCRIPTION
Fan Commanded to Max Heat Speed
Manual Mode
Fan Commanded to Standby Speed
Manual Mode
DO13 override on command
Manual Heat Enable Command
Manual Cool Enable Command
Heat mode status
Cool mode status
Occupancy command
Standby command
Occupancy mode status
Standby mode status
Occupancy effective command from
push button override or motion sensor
Set Damper Full Open Manual Mode
Set Damper Full Close Manual Mode
Damper set to Max Flowrate Manual
Mode
Damper set to Min Flowrate Manual
Mode
Damper set to Fire Stop Cmd
True will allow measured flow to be
entered at (A218), False will allow
factory K-factor to be entered at (A218)
Load Shed Enable Effective Command
Fan Commanded to Min Heat Speed
Manual Mode
Load Shed Enable Command
Box damper will be overridden open.
If any outputs have been overridden
this point will be on
If any TAB manual mode override points
have been set to on this point will be on
If any inputs have been overridden this
point will be
ON
When adaptation is selected, the
actuator will drive one full cycle to its
mechanical end-stop, and when it
reaches that point the actuator's
working range will be adapted to the
actual mechanical angle of rotation. To
initiate this process, toggle point D225
On, then toggle it Off.
If commanded to Purge mode this point
will be on
Reverses damper action
0 = CW open, CCW close
1 = CW close, CCW open
This point enables unoccupied cooling
If any input, outputs, or manual status
application mode is on, this point is on
UI04 digital status host
ACTIVE INACTIVE DEFAULT VALUES
TEXT TEXT
IMP STG.
STG.
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
Non
Occ 1
Occ
On Off 0
Non
Occ 0
Occ
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
Enable Disable 0
On Off 0
Enable Disable 0
On Off 0
Enable Disable 0
Enable Disable 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
Enable Disable 1
On Off 0
On Off 0
MET
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
69