SOMFY RTS - Shutter In-Wall Receiver Manual

Installation

The Shutter in-wall receiver RTS is compatible with all Somfy wired motors (I<3 A-240V or I<3.4 A-120V).

Compatible transmitters (12 max)

The Shutter-in-wall receiver RTS is compatible with all Somfy RTS transmitters and Somfy sun sensors. Please refer to the corresponding instructions.

Installation recommendations

• The receiver must be installed in a lised electrical box by a licensed electrician or a a qualified professional of motorisation or automation in accordance with these instructions and with local and national electrical codes.
• Never connect several receivers RTS to one motor.

Wiring

• 
  Do not reverse the neutral and live wiring connections. Cut the power at the circuit breaker before any work on the product. The mains power supply voltage must be consistent with the motor label: 240V~50/60 Hz or 120V~60 Hz. After installation, the wires into the terminals must not be under physical tension.
• Only connect one external switch to the control's input wires (only one fi xed or momentary position switch). If no switch is connected to the receiver RTS, cap off wires 6, 7 and 8. Put an insulation plate on the front.
• Confirm the ▲ and ▼ directions are connected correctly to the switch.
• We recommend that you use a tool to push down on the terminal's insertion grips during wiring and unwiring.

Confirming the wiring of the switch

• If pushing the button makes the roller shutter go down, reverse the brown (US=black) and black (US=red) motor wires.
  

Setting the limit switches

• If it is necessary to set the motor limits, use the wired switch to set the limits before programming a transmitter. (Please refer to the instructions for the corresponding motor).

Programming the receiver

The product should be fully installed before it is powered and used.

Adding/Deleting control points or sensor RTS

(the procedure for adding or deleting a control point is the same):

1. Press and hold the receiver's PROG button until the shutter moves up and down.
   
2. Press briefly the PROG button on the new transmitter (or sensor), the shutter moves up and down.
   

Setting or modifying the favourite position

1 (accessible from the bottom position) and 2 (accessible from the top position):

1. Position the motor on its limit: bottom to store 1 in the memory or top to store 2 in the memory.
2. Press for 3 seconds simultaneously on the buttons: and (for 1) or and (for 2) of the transmitter. When the roller shutter arrives at the desired position, press the button. Adjust the position if necessary using the and buttons.
3. Press the button for 5 seconds to store the position in the memory, the roller shutter moves the up and down.

• To use an intermediary position, position the motor on its limit: bottom for 1 or top for 2 and then press the button for < 1 sec. The motor will run to the the intermediate position.

Sun function

Removing all the transmitters and sensors from shutter in-wall receiver RTS

• Press the PROG button of the receiver RTS for more than 7 seconds until the roller shutter moves up and down once then a second time a few moments later.

Functioning of the wired control (fixed or momentary)

• A < 0.5 sec. press on the button up or down will send the roller shutter to the limit switch.
• A > 0.5 sec. press on the button up or down will command the roller shutter for the period of time of the press.
• A command repeated on the same button causes it to stop.

Characteristics

• Motor output: 3A max. under 240V or 3.4A max. under 120V.
• Functioning limited to only one motor.
• Radio: 433.42 MHz
• Dimensions (mm): 19 x 41 x 45
• Storage temperature: -30°C +70°C
• Temperature for utilisation: -20°C +55°C
• European compliance: CE
• Environmental classifi cations: Insulation Cat III and Pollution Cat II
• Protection index: IP20 as long as installation instructions are complied with. For indoor use only (protection against solid matter with a diameter of > 12 mm, no protection against fl uids).
• Please ensure you dispose of waste products using your local refuse collection system.
• Maximum altitude for use: 2000 metres.
• Product sensitive to knocks and falls.

Any use outside the sphere of application specified by Somfy is forbidden. In this event, as for all usage not consistent with the instructions given here, Somfy declines any responsibility for harm or damage. Never begin installing without fi rst checking the compatibility of this product with the associated equipment and accessories.

Somfy hereby declares that the product conforms with the essential requirements and other relevant provisions of the European Directives applicable for Europe. A Declaration of Conformity is available at www.somfy.com/ce.

Documents / Resources

References

• Declarations of conformity

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download SOMFY RTS - Shutter In-Wall Receiver Manual