Amantii TRU VIEW Series Repair Manual
  1. Manuals
  2. Brands
  3. Amantii Manuals
  4. Indoor Fireplace
  5. TRU VIEW Series
  6. Repair manual

Amantii TRU VIEW Series Repair Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TRU VIEW SERIES
TRV BESPOKE REPAIR GUIDE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TRU VIEW Series and is the answer not in the manual?

Questions and answers

Related Manuals for Amantii TRU VIEW Series

Summary of Contents for Amantii TRU VIEW Series

  • Page 1 TRU VIEW SERIES TRV BESPOKE REPAIR GUIDE...
  • Page 2 SAFETY FIRST TO AVOID ANY ELECTRICAL SHOCK OR POTENTIAL DAMAGE TO THE UNIT REMEMBER TO TURN THE POWER OFF TO THE UNIT BEFORE ATTEMPTING TO REMOVE OR INSTALL ANY PARTS.

  • Page 3: Table Of Contents

    Table of Content • Replacing the canopy LED strip • Replacing the flame LED strip • Replacing the motor • Replacing the ember bed LED strip • Replacing the WiFi PCB • Replacing the heating element • Replacing the PCB Board •...

  • Page 4: Replacing The Canopy Led Strip

    REPLACING THE CANOPY LED STRIP Remove the 3 screws ( as shown in the diagram). The quantity of screws Step 1 varies and depends on the size of the unit. Remove the front glass brackets that holds the glass securely in place...
  • Page 5 Carefully remove the front glass and place it in a safe location. Step 2...
  • Page 6 Remove the 3 screws ( as shown in the diagram). The quantity of Step 3 screws varies and depends on the size of the unit. The canopy light assembly can now be removed...
  • Page 7 Remove the screws from the defective LED strip and unplug the molex Step 4 connector to replace it with a new LED strip...
  • Page 8 REPLACING THE FLAME LED LIGHTS Follow STEPS 1 through 3 from REPLACING THE CANOPY LED: Remove the 2 screws and the brackets that hold the left and right sides and Step 1 left side glass in place. Safely remove the side glass pieces and take off the brackets.
  • Page 9 Using a bracket safely pry up the tray glass. Carefully take off the tray Step 2 glass and place it in a safe place.
  • Page 10 Remove the 5 screws ( as shown in the diagram). The quantity of Step 3 screws varies and depends on the size of the unit. Carefully remove the bracket that holds the back glass...
  • Page 11 Carefully remove the back glass and place it in a safe spot. Step 4...
  • Page 12 Remove the 8 screws ( as shown in the diagram). The quantity of Step 5 screws varies and depends on the size of the unit. The flame effect steel panel can now be removed the flame effect steel panel...
  • Page 13 Remove the 3 screws ( as shown in the diagram). The quantity of Step 6 screws varies and depends on the size of the unit. The light barrier can now be removed. light barrier...
  • Page 14 Removing the flame reflector. Step 7...
  • Page 15 When the flame reflector is removed, the flame LED will be visible. Step 8 The LED strips are held in place with screws and are connected to the other strips by using a molex connector. Unscrew the screws of the failed LED strip and unplug the molex connector to replace it with a new one.

  • Page 16: Replacing The Motor

    REPLACING THE MOTOR Follow STEPS 1 through 3 from REPLACING THE FLAME LED...
  • Page 17 Remove the ember bed reflector. Step 1...
  • Page 18 By removing the two screws circled in red, you will be able to loosen the Step 2 motor PCB connector from the fireplace, and then you will be available to unplug the spade connectors...
  • Page 19 Remove the 6 screws circled in red to take out the failed motor. A new Step 3 motor can now be safely installed.

  • Page 20: Replacing The Ember Bed Led Strip

    REPLACING THE EMBER BED LED STRIP Follow STEP 1 from Replacing the motor. The Tru View – TRV Bespoke series of fireplaces contains 2 LED strips for the ember bed. The rear set of LED strips for the ember bed is situated here The front set of LED strips for the ember is situated here.
  • Page 21 Remove the 5 screws ( as shown in the diagram). The quantity of screws Step 1 varies and depends on the size of the unit. The bracket that is holding the rear LED strips in the ember bed can now be removed. LED strips in front for ember bed are held in place with screws and are connected to the other strips or to the end using a molex connector.
  • Page 22 Remove the 3 screws ( as shown in the diagram). The quantity of screws Step 2 varies and depends on the size of the unit. The bracket that is supporting the ember bed glass can now be removed. LED strips in front for ember bed are held in place with screws and are connected to the other strips or to the end using a molex connector.

  • Page 23: Replacing The Wifi Pcb

    REPLACING THE WIFI PCB Follow STEPS 1 through 4 from REPLACING THE FLAME LED LIGHT. The WiFi PCB is located under the middle plate Remove the 6 screws circled in red to take out Step 1 the WIFI PCB from the fireplace. Remove the 6 screws circled in red to remove Step 2 the WIFI PCB from the fireplace.

  • Page 24: Replacing The Heating Element

    REPLACING THE HEATING ELEMENT Follow STEPS 1 through 4 from REPLACING THE FLAME LED LIGHT. Remove the screws circled in red to take off the metal tray . Then the metal Step 1 tray can be taken out of the fireplace. The heating element, PCB board, AC adapter, bluetooth speaker set and speaker set are all place...
  • Page 25 TRV 45 METAL TRAY heating element PCB board AC adapter speaker set bluetooth speaker set...
  • Page 26 TRV 55-85 METAL TRAY heating element PCB board AC adapter speaker set bluetooth speaker set...
  • Page 27 Unscrew the screws circled in red to take off heating element assembly Step 2 from the mental tray. TRV 45 metal tray TRV 55-85 metal tray...
  • Page 28 Unplug the heater and replace it with a new heater. Step 3...

  • Page 29: Replacing The Pcb Board

    REPLACING THE PCB BOARD Follow STEP 1 in Replace the heating element. Remove the 4 screws circled in purple and replace the failed PCB board with a new one. Secure the new board to the metal tray using the same 4 screws used to remove the board.

  • Page 30: Replacing The Ac Adapter

    REPLACING THE AC ADAPTER Follow STEP 1 in Replace the heating element. Unscrew the screws circled in red. The AC adapter is connected to the PCB board using a molex connector. Follow the lead from the AC adapter back to the board and disconnect it from the PCB board. A new receiver can be connected to the PCB board then secured to the mental tray of unit.

  • Page 31: Replacing The Bluetooth Speaker Set

    REPLACING THE BLUETOOTH SPEAKER SET Follow STEP 1 in Replace the heating element. Remove the screws circled in pink to disconnect the bluetooth speaker set from the mental tray. Unplug the bluetooth speaker set and replace it with a new bluetooth speaker set. It is recommended to record the connection mode by photo before replacing the new...

  • Page 32: Replacing The Speaker Set

    REPLACING THE SPEAKER SET Follow STEP 1 in Replace the heating element. Remove the screws circled in red to disconnect the speaker set from the mental tray. Unplug the speaker set and replace it with a new speaker set. speaker set It is recommended to record the connection mode by photo before...

  • Page 33: Replacing The Touch Panel Circuit Board

    REPLACING THE TOUCH PANEL CIRCUIT BOARD Follow STEP 1 to 4 in replace led strip for Flame, you can come to here. The area circled in red is where touch panel is inserted into the motherboard...
  • Page 34 Remove the screws circled in red to take off the metal tray . Then the metal Step 1 tray can be take out of the fireplace. Circuit Board for Touch Panel...
  • Page 35 Remove the screws circled in red to take off the Circuit Board for Touch Panel Step 2 Unplug the molex connector (in the big mental tray )and replace it with a new Circuit Board for Touch Panel.

This manual is also suitable for:

Trv bespoke

Table of Contents