Table of Contents
Advertisement
Quick Links
INSTALLATION AND OPERATION INSTRUCTIONS FOR
TRV-55 BESPOKE BS2100055-1
TRV-65 BESPOKE BS2100065-1
TRV-75 BESPOKE BS2100075-1
TRV-85 BESPOKE BS2100085-1
If the information in these instructions are not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss
of life.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other.
ELECTRIC FIREPLACE
www.amantii.com
SAFETY INFORMATION
WARNING
01
REVISED - 06/20/22
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Amantii TRV-55 BESPOKE
Summary of Contents for Amantii TRV-55 BESPOKE
- Page 1 ELECTRIC FIREPLACE www.amantii.com INSTALLATION AND OPERATION INSTRUCTIONS FOR TRV-55 BESPOKE BS2100055-1 TRV-65 BESPOKE BS2100065-1 TRV-75 BESPOKE BS2100075-1 TRV-85 BESPOKE BS2100085-1 SAFETY INFORMATION WARNING If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
- Page 2 INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE. CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE. WARNING: This product can expose you to chemicals including lead in the wiring, which is [are] known to the State of California to cause birth defects of other reproductive harm. For more information visit: www.p65warnings.ca.gov REVISED - 06/20/22...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Please read and carefully follow all of the instruction found in this manual. The instructions included here will assure that you have many years of dependable and enjoyable service from your Amantii Electric Fireplace. IMPORTANT INSTRUCTIONS CAUTIONS... -
Page 4: Important Instructions
IMPORTANT INSTRUCTIONS 1. Read all instructions before installing or using this heater. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surface. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet from the front, sides and rear of the heater. -
Page 5: Cautions
CAUTIONS Always install the heater in accordance with this guide. If in doubt obtain expert advice. Always make sure the electrical socket is accessible and located adjacent to, but not above the heater. Always disconnect the heater from the electrical supply before moving it, or carrying out cleaning, maintenance. -
Page 6: Fcc Cautions
FCC CAUTIONS This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. -
Page 7: Unpacking And Testing Appliance
UNPACKING AND TESTING APPLIANCE Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance operates properly by plugging the power supply cord into a 120 Volt grounded outlet. Test all aspects of its operation (manual switches, remote and heater) to make sure all components are operating correctly. - Page 8 Do not share a socket with other appliances when using electric fireplaces, please use a dedicated socket. Never use with an extension cord or relocatable power tap (outlet / power strip).
-
Page 9: Product Specification
In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI/NFPA 70 National Electrical Code in the United States. BS2100055-1 BS2100065-1 BS2100075-1 BS2100085-1 Product model TRV-55 BESPOKE TRV-65 BESPOKE TRV-75 BESPOKE TRV-85 BESPOKE Voltage 120V AC 60Hz 240V AC 60Hz... -
Page 10: Outdoor Installation
OUTDOOR INSTALLATIONS Our Tru View Bespoke electric fireplaces are suitable for outdoor areas protected from direct water impingement. The fireplace shall not be installed in a standalone structure, even if the following requirements are met. In addition to maintaining the listed mantel and combustible clearances, a rain protection overhang factor of ½... -
Page 11: Hardwire Installation
HARDWIRE INSTALLATION Turn off the appliance completely and let cool before servicing. Only a qualified service person should service and repair this electric appliance. If it is necessary to hardwire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the household wiring. - Page 12 Connect to 240V 1. Test the unit before removing the cord. Remove the cover plate from the back top right corner of the appliance by removing the four screws, as shown below. Unscrew and remove power cord. Disconnect the N G L 2.
-
Page 13: Installation
The wall opening size of the fireplace: 2. To view the flame from different angles, you need to remove panels from different sides. 56 1/8” 15” 29 3/4” TRV-55 BESPOKE 142.7 cm 38.2 cm 75.6 cm (1). Remove both sides of the fending 66 1/8” 15”... - Page 14 (3). Remove the fending panel on the right 5. Make an opening for the fireplace side if you want to view the flame from according to requested measurement. front and right side. 3. Screw back the fending bar after the panel is removed.
- Page 15 7. After checking that the fireplace operates properly, cover the glass panels with protective plastic bag and install plywood or drywall. Three angles viewing Front and right side viewing Front and left side viewing...
-
Page 16: Side By Side Installation
SIDE BY SIDE INSTALLATION 4. Unscrew 2 screws and remove the brackets which are fending the right side glass. 1. Unscrew 7 screws on the right side that fix the fending bar and panel, and then take off 2. Unscrew 3 screws （The quantity varies depending on the size of the unit）and remove the front glass bracket which are fending the front glass. - Page 17 7. Place fireplace 1 and fireplace 2 on the same level and place the right side of fireplace 1 close to the left side of fireplace 2. 8. Unscrew the 8 screws at the joint, then remove the 2 framing plates from the fireplace 1 and fix them as the picture shows.
-
Page 18: Media Installation
3. Installing the fire glass media. Pour the MEDIA INSTALLATION fire glass media into the tray as shown below. Feel free to use any combination of fire 1. Unscrew 3 screws（The quantity varies glass media that you find most appealing. depending on the size of the unit）... -
Page 19: Manual Operation
MANUAL OPERATION The fireplace operates either by the touch panel located on the left front top side of the fireplace or by supplied remote control. Ensure that the ON / OFF Power Switch on the fireplace is in the ON position. Touch the control panel once to “wakes up”... -
Page 20: Remote Control Operation
REMOTE CONTROL OPERATION For the remote to function make sure the fireplace is plugged in and the ON / OFF Power Switch on the fireplace is in the ON position and the remote has batteries. Important: When operating the remote make sure you point the remote to the center of the fireplace. - Page 21 Each time Speed Button is pressed, the speed of the flame will change. Three options are available: Medium- High- Low. The Moodlight Button turns the moodlight on and off. When in on position, the display screen of the remote control shows AD 1, when the number “1” flash, you can set the color of moodlight with keys.
- Page 22 7 day timer function NOTE: Ensure that the current time setting accurate, otherwise the effective time of the 7 day timer function will be different from what you set. Press the key once, 7 days from Monday to Sunday will display on the LCD screen of the remote control, press key within 5 seconds to enter 7 day timer function .
-
Page 23: Trouble Shooting
TROUBLE SHOOTING Fault code Fault Cause Solution The heater overheating Call after-sales service. NTC is defective. Call after-sales service. If the vents are dirty or clogged. Unplug the power, The heater not working. clean the dust and debris of the vent area. Wait for 5 minutes, plug in and turn on the heater. -
Page 24: Replacement Parts
REPLACEMENT PARTS PART NUMBER DESCRIPTION BS2100055-1 BS2100065-1 BS2100075-1 BS2100085-1 (TRV-55 BESPOKE) (TRV-65 BESPOKE) (TRV-75 BESPOKE) (TRV-85 BESPOKE) Trim not applicable Adjustable Screws 40000174 Front Glass Bracket 10002855P 10002855P 10002899P 10002901P Front Glass 60000265 60000268 60000271 60000274 Back Glasss 60000266 60000269... -
Page 25: Exploded View
EXPLODED VIEW... -
Page 26: Wiring Diagram
EMBER BED LIGHT XTL:26MHz ANTENNA WIFI PCB POWER PCB KEY PCB BLUETOOTH PCB ANTENNA XTL:24MHz LOUDSPEAKER... -
Page 27: Electric Fireplace Warranty
Products covered by this limited warranty have been tested and inspected prior to shipment and, subject to the provisions of this warranty, Amantii warrants such products to be free from defects in material and workmanship for a period of five (5) years from the date of the first purchase of such products. - Page 28 The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty. GENERAL Amantii reserves the right to make changes at any time without notice, in design,...
Need help?
Do you have a question about the TRV-55 BESPOKE and is the answer not in the manual?
Questions and answers