Related Manuals for Viessmann VITOTROL 100-E
Summary of Contents for Viessmann VITOTROL 100-E
- Page 1 VIESMANN Operating instructions for the system user Vitotrol 100-E Wireless remote control for 1 heating circuit VITOTROL 100-E Please keep safe. 6192459 GB 7/2022...
-
Page 2: Safety Instructions
Safety instructions Safety instructions Please follow these safety instruc- tions closely to prevent accidents and material losses. Safety instructions explained Danger Note This symbol warns against the risk Details identified by the word "Note" of injury. contain additional information. Target group These instructions are intended for sys- Danger tem users. - Page 3 Safety instructions Safety instructions (cont.) Auxiliary components and individual parts For replacement, use only spare parts supplied or approved by Viessmann.
- Page 4 5. Commissioning Adjusting your Viessmann appliance ..........15 Commissioning the Vitotrol 100-E ............15 ■ Inserting the Vitotrol 100-E in the mounting base ........16 6. Using the remote control Using the remote control ................ 17 Overview of controls ................17 ■...
- Page 5 Messages shown on the display ............27 What to do if... Faults without fault display ..............29 Cause of fault could not be found ............29 Restarting the Vitotrol 100-E ..............29 12. Maintenance Replacing the batteries ................31 Cleaning ....................32 13.
- Page 6 Viessmann appliance (recommendation). Reliable remote control operation: ■ The control unit of the Viessmann appliance and the Settings for WiFi and low power radio at the Vitotrol 100-E remote control must be connected via connected Viessmann appliance: low power radio.
-
Page 7: Introductory Information
Introductory information Disposal of packaging Please dispose of packaging waste in line with statu- tory regulations. Symbols Symbol Meaning Reference to other document containing further information Step in a diagram: The numbers correspond to the order in which the steps are carried out. Warning of material losses and environ- mental pollution Live electrical area... -
Page 8: Product Information
Vitotrol 100-E is connected to the control unit of the ate or low humidity. Viessmann appliance via "low power radio". For opera- tion with a Vitotrol 100-E, the control unit of the Viess- Note mann appliance must be set to "15: Individual room No more than 1 Vitotrol 100-E can be configured for control (On/Off)"... -
Page 9: Remote Control
Remote control Commissioning of the Vitotrol 100-E: See page 14 15. Your system has been preset The control unit preset at the factory. - Page 10 Example: Late in the evening, the reduced room DHW is available immediately from the taps. This temperature is set by the time program. Your guests setting can only be made at the control unit of the stay longer. Viessmann appliance. Operating instructions for Viessmann heat generator...
-
Page 11: Installation Location
Note The poorer the reception quality, the longer it takes ■ for the Vitotrol 100-E to establish a connection to the Viessmann appliance. It can take up to 6 minutes to establish the connection. ■... - Page 12 Installation location (cont.) To extend the range of the wireless signal, the follow- ing repeaters can be used: ■ Viessmann ViCare repeater for surface mounting ■ Ubisys repeater Angle of penetration The reception quality remains best if radio signals hit Ideal angle of penetration the walls vertically.
-
Page 13: Installation Sequence
Overview of the installation and commissioning process Steps Responsibility Page Check system requirements. Contractor IT expert Fit the mounting base for the Vitotrol 100-E. Contractor System user Establish a power supply via batteries. Contractor System user Commission the Vitotrol 100-E. - Page 14 Installation sequence Establishing a power supply via batteries (cont.) 2 x AA 2 x 1,5 V Fig. 4...
- Page 15 "16: Individual room control with modulation (modulation control)" using the ViGuide software 4. Follow the instructions in the app to register. tool. 5. Assign the Vitotrol 100-E to your Viessmann appli- Installation and service instructions of the ance via ViGuide. Viessmann appliance 2.
- Page 16 Commissioning Inserting the Vitotrol 100-E in the mounting base Fig. 5...
- Page 17 Takes you directly to the submenu, where All settings are transferred from the Vitotrol 100-E to you can set room temperatures for the tem- the Viessmann appliance and vice versa. It is always perature levels.
- Page 18 "Standby mode" can only be activated and deactivated on the Viessmann appliance. To switch off heating via the Vitotrol 100-E, the lowest settings for the temperature lev- els can only be selected in the "heating mode" operating program.
- Page 19 Screed drying: ■ This function is activated by your contractor at the control unit of the Viessmann appliance (if the Viess- mann appliance supports this function). Your screed is dried in line with a set time program (temperature/ time profile) suitable for the relevant building materi- als.
- Page 20 Using the remote control Procedure for setting a time program (cont.) Setting time phases Explanation of the procedure using the example of to set the minutes for the start of the time room heating phase ("START") to 30 minutes. You can set up to 4 time phases in each "Time pro- 04.
- Page 21 Using the remote control Procedure for setting a time program (cont.) Deleting time phases Explanation of the procedure using the example of 5. OK to confirm room heating for the required time phase 2 Example: For Monday you want to delete time phase 2. 7.
- Page 22 If the actual room temperature exceeds the current set the set room temperature of the temperature level can room temperature, room heating is automatically be lowered via the Vitotrol 100-E so that the heating is switched off. switched off. For information on the operating programs, see...
-
Page 23: Central Heating
Central heating Temporarily adjusting the room temperature If you want to heat your home with the normal room Your home will be heated with the temperature of the temperature or comfort room temperature during a last active time phase for standard room temperature/ time phase with reduced room temperature, switch on flow temperature or comfort room temperature/flow the "Extended heating"/"Extend time phase once"... -
Page 24: Setting The Dhw Temperature
DHW heating Starting DHW heating DHW is heated according to the set time program. If you switch off DHW heating, no water can be heated. Press the following buttons: for "DHW ONOFF" 5. OK to confirm for "DHW" for "ON" 3. -
Page 25: Further Settings
We recommend connecting the Viessmann appliance cally updated. The software is transmitted to the permanently to the WiFi so that the Vitotrol 100-E soft- remote control via low power radio and updated. The ware is always up to date. -
Page 26: Restoring Factory Settings
Your contractor has to update the settings for the ■ OK to confirm remote control on the control unit of your Viessmann appliance too, e.g. heat generator. 7. OK to confirm the prompt The remote control is reset to the factory settings. -
Page 27: Messages Shown On The Display
Diagnosis and service checks Calling up device information In the "DEV INFO" menu you can call up the following information for the Vitotrol 100-E: Shown on display Explanations "SW VERS" Software version "RF RANGE" Signal strength of low power radio in dBm "ADJUST"... - Page 28 Check the signal strength of the "low pow- ■ er radio" in the "DEV INFO" menu of your Vitotrol 100-E: See page 27. If necessary, move the Vitotrol 100-E to a ■ different installation location: See page 11. Restart the Vitotrol 100-E: See page 29.
- Page 29 All displays on the Vitotrol 100-E are off. Cause Remedy The batteries in the Vitotrol 100-E have nearly run out. Replace the batteries; see page 31. Cause of fault could not be found Find out about any possible troubleshooting measures...
- Page 30 What to do if... Restarting the Vitotrol 100-E (cont.) 10 s Fig. 9 Fig. 10...
-
Page 31: Replacing The Batteries
Maintenance Replacing the batteries We recommend the use of AA batteries as they last longer than rechargeable ones. Fig. 11 2 x AA 2 x 1,5 V Fig. 12... - Page 32 Maintenance Replacing the batteries (cont.) After the batteries are inserted, the remote control adopts all settings from the connected Viessmann appliance. Fig. 13 Cleaning You can clean the surfaces of the device with a microfi- bre cloth. Never use cleaning agents.
-
Page 33: Specification
Specification Specification Vitotrol 100-E Power supply Via batteries: 2 x 1.5 V AA (LR06) Protection class IP rating IP 20D to EN 60529, ensure through design/installation. Low Power Radio Status Radio frequency 2.4 GHz Encryption Encrypted Wireless range through walls... - Page 34 This product comprises third party software and/or open source software. You are authorised to use this software subject to compliance with the relevant licensing terms. The following open-source software components are used in the Vitotrol 100-E: Name Version Download URL...
- Page 35 Appendix Licences (cont.) 3. Grant of Patent License You may add Your own copyright statement to Your modifications and may provide additional or different Subject to the terms and conditions of this License, license terms and conditions for use, reproduction, or each Contributor hereby grants to You a perpetual, distribution of Your modifications, or for any such worldwide, non-exclusive, no-charge, royalty-free,...
-
Page 36: Operating Program
How you heat your rooms. ■ Whether you heat DHW. ■ Whether only frost protection for the Viessmann appliance and DHW cylinder is active. Screed drying Your contractor can activate this function for screed drying, for example in your new build or extension. -
Page 37: Heating Circuit
Appendix Terminology (cont.) Screed drying affects all heating circuits: ■ All rooms are heated according to the temperature/ time profile. Your settings for central heating have no effect on the duration of screed drying (max. 32 days). DHW heating is enabled. ■... -
Page 38: Room Temperature
In the time programs, you specify what your system should do at what time. Final decommissioning and disposal of the remote control Viessmann products can be recycled. Components DE: Operating fluids (e.g. heat transfer medium) can and fluids from your heating system do not belong in be disposed of at municipal collection points. - Page 39 Certification Certification...
- Page 40 Keyword index Keyword index Frost protection............6 Actual room temperature, correcting......27 Frost protection monitoring........22 Ambient temperature Vitotrol 100-E......11 Angle of penetration........... 12 General Terms and Conditions........6 Glossary..............36 Batteries..............13 Battery replacement..........18, 31 Heating – Comfort..............10 Central heating –...
- Page 41 Keyword index Keyword index (cont.) Requirements...............6 Temperature level............22 Reset................26 Terminology..............36 Restart Vitotrol 100-E..........29 Terms and Conditions..........6 Room heating Time................25 – Symbol..............17 Time phase deletion........... 21 Room temperature............9 Time phases – Changing..............22 – Central heating............22 Room temperature............. 10 –...
- Page 44 Viessmann Climate Solutions SE Viessmann Limited 35108 Allendorf / Germany Hortonwood 30, Telford Telephone: +49 6452 70-0 Shropshire, TF1 7YP, GB Fax: +49 6452 70-2780 Telephone: +44 1952 675000 www.viessmann.com Fax: +44 1952 675040 E-mail: info-uk@viessmann.com...