Page 1
INSTALLATION AND OPERATION INSTRUCTIONS FOR CUBE-2025WM SAFETY INFORMATION WARNING If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
Please read and carefully follow all of the instruction found in this manual. Please pay special attention to the safety instructions provided in this manual. The instructions included here will assure that you have many years of dependable and enjoyable service from your Amantii product. Contents IMPORTANT INSTRUCTIONS ..........................
IMPORTANT INSTRUCTIONS 1. Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause fire or injury. 2. Keep combustible materials such as furniture, pillows, bedding, clothing, curtains and paper at least 3 ft from the front, sides and rear of the heater.
UNPACKING AND TESTING APPLIANCE Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance operates properly by plugging the power supply cord into a conveniently located 120 Volt grounded outlet. Test all aspects of its operation (manual switches, remote and heater) to make sure all components operate correctly.
CUBE-2025WM Description This appliance has been tested in ELECTRIC FIREPLACE accordance with the UL Standard 2021 Voltage 120V AC 60Hz 1465W Max for fixed and location dedicated Watts electric room appliances in the United NO HEATER States and Canada. If you need...
INSTALLATION WALL-MOUN NOTE: Due to the many differe ent materials used on different walls, it is h highly recommended that you consult your local build der before you install this appliance. 1. Select a location that is not prone to moisture and is located at lea ast 0.91 m or 3 feet away from combustible...
INSTALLATION CUBE-BASE-LE 1. Screw the base legs to the stee el panel. 3. Place the unit onto t the base leg and screw in the adjustable fee et, fixing the unit and the base leg. 2. Unscrew the adjustable feet fr rom the 4.
INSTALLATION CUBE-BASE-SPEAKER 1. Unscrew the adjustable feet from the unit. 3. Place the unit on the CUBE-BASE-SPEAKER and screw in the adjustable feet, fixing the unit and the speaker box. 4. Plug into the back of the unit. Re-install 2. Unscrew the rear screws and remove the the back steel panel.
Page 9
INSTALLATION OUTDOOR CUBE electric fireplaces are suitable for installation in outdoor areas protected from direct water impingement. In addition to maintaining the listed mantel and combustibles clearances, a rain protection overhang factor of 1/2 shall be constructed to the front and to each side of the installed appliance.
HARD- WIRE INSTALLATION Turn off the appliance completely y and let cool before servicing. Only a qualifie ed technician should service and repair this elec ctric appliance. If it is necessary to hard wire this a appliance, a qualified electrician must remov ve the cord connection, and wire the appliance directly to the house hold wiring.
MEDIA OPTIONS Your fireplace shipped with DESIGN- MEDIA-BIRCH-10PCE. DESIGN-MEDIA-BIRCH-10PCE STEP 4: After finishing decoration, re-install MEDIA INSTALLATION the front glass panel using the securing STEP 1: Unplug the unit and make sure screws removed in step 2. controls are switched off. STEP 2: Unscrew 2 adjustable screws that securing the front glass panel.
OPERATION The fireplace can be operated eith her by the switches located on the left front o of the fireplace unit or by supplied remote control. MANUAL OPERATION 1. The main power ON/OFF swit tch in position O, the fireplace is OFF. 2.
REMOTE CONTROL OPERATI For remote to function make sure e the heater is plugged in and main power sw witch located on the bottom left hand side is at positio on I. When operating the remote make e sure you point the remote to the center of the fireplace and make sure each time you press the butt ton the buzzer inside the unit will beep once...
INSTALLING WALL THERMOSTAT WALL THERMOSTAT WIRING DIAGRAMS Wire the wall thermostat prior to installing the fireplace. WALL THERMOSTAT WIRING (24 VAC) Install Wall Thermostat per instructions provided with kit and per the following information: 1. Turn off circuit breaker. 2. Remove cover plate located on the left side of appliance. Pull the wire out and cut the inside thermostat.
REPLACEMENT PARTS This list contains replacement parts PART NUMBER DESCRIPTION QTY. 10701357 FRONT CLEAR GLASS (MIDDLE) 10201505 ADJUSTABLE SCREW 3123010 FIXER FOR FRONT GLASS PANEL 10701356 SIDE GLASS PANEL 10702216 VISUAL GLASS 10702215 BOTTOM GLASS 602082 BLOWER AND HEATER ASSEMBLY 601036 CONTROL PANEL 10104002...
TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Dim or no flame Flame LED’s are burnt out. Inspect the LED’s and replace them if necessary. Back black cloth is falling off Change a flicker and back black cloth. and rolled up in the flicker. Ember Ember LED’s are burnt out Inspect the ember bed LED’s and...
SERVICE HISTORY This heater must be serviced annually depending on usage. Date Dealer Service technician Service Performed Special Concerns Name Name NOTES:...
Page 20
Amantii warrants such products to be free from defects in material and workmanship for a period of two (2) years from the date of the first purchase of such products. The limited two (2) year warranty period for products also applies to any implied warranties that may exist under applicable law. Some...
Need help?
Do you have a question about the CUBE-2025WM and is the answer not in the manual?
Questions and answers