Chapter 8 Jumper Configuration - Renesas RH850/E2x373BGA User Manual

Chapter 8 Jumper Configuration

R20UT4126ED0120 Rev. 1.2
2017-10-25
Jumper are available to configure the function of the board. This chapter
describes the standard configuration, i.e. jumper setting for the intended devices,
to enable basic operation. For a detailed explanation of the supported function of
the used device, please refer to the corresponding HW user's manual.
Table 9 Recommended Jumper Settings
Purpose
5.0V Main
3.3V Main
5.0V Analog Main
3.3V Analog Main
E0VCC Config
E1VCC Config
E2VCC Config
LVDVCC Config
SYSVCC Config
VCC Config
EMUVCC
VDDIOF
A0VCC Config
A0VREFH Config
A1VCC Config
A1VREFH Config
A2VCC Config
A2VREFH Config
A3VCC Config
A3VREFH Config
ADSVCC
ADSVREFH
1.25V Source
EMUVDD
CN9 Pull-Up 1-9
MD0 Pull-Up
MD1 Pull-Up
EVTO Pull-Up
HS-SPI IC4 Config
Board_VCC Config
TRST Config
CN9 Pull-Up 11-19
ADSVREFL Pull-Down
AURORES Config
Note 1): Optionally for the FCC1 device only. If any of the FCC1 specific features
are used (e.g. ERAM, Aurora Trace ...) these jumpers needs to be set.
Note 2): Optionally for the FCC1 device only, if Aurora Trace is used. Please
refer to the user's documentation of the used tool for dedicated requirement.
The table has the following meaning:

o: Jumper must be connected.

o (opt): Recommended to be connected. Can be left open if not
necessary for use case

-: Jumper must be left open
Jumper #
FCC1 for E2M
0
*1)
1
2
3
4
#1-#2 only
5
6
7
8
9
*1)
10 #2-#3 only (opt)
11
12
#1-#2 only
13 #1-#2 only
14
#1-#2 only
15
#1-#2 only
16
#1-#2 only
17
#1-#2 only
18 #1-#2 only
19
#1-#2 only
20
#1-#2 only
21
#1-#2 only
22
VDD 23
*1) 24
25
26
27
28
29
30
31
32
33
*2) 34
#1-#2 (opt)
Device
RH850/E2M in BGA373
E2M
o o
o (opt) - (opt)
o o
- (opt) - (opt)
#1-#2 only
#1-#2 #1-#2
#1-#2 #1-#2
#1-#2 #1-#2
#1-#2 #1-#2
#1-#2 #1-#2
#1-#2 #1-#2
#1-#2 only
#1-#2 only
#1-#2 only
#1-#2 only
#1-#2 only
#1-#2 only
#1-#2 only
#1-#2 only
#1-#2 only
#1-#2 only
#1-#2 #1-#2
o o
o (opt)
- (opt) - (opt)
- (opt) - (opt)
- (opt) - (opt)
- (opt) - (opt)
- (opt) - (opt)
#1-#2 #1-#2
#2-#3 #2-#3
- (opt) - (opt)
o o
#2-#3 only
-
-
16