Table of Contents
Advertisement
Quick Links
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
A.
Top
1 pc.
F.
Rail
1 pc.
G.
Rail
1 pc.
H.
Rail
1 pc.
J.
Rail
2 pcs.
K.
Shelf
1 pc.
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8" Drill Bit
home
5053-49
Hall Tree
B.
Side Frame
1 pc.
L.
Seat
1 pc.
N.
Base
1 pc.
M6x16
Head Cap Bolt
45 pcs. (+1 extra)
M x
6 13
Tapered Bolt (short)
16 pcs. (+1 extra )
styles Customer Service: www.homestylesfurniture.com,
servicedesk@homestylesfurniture.com,
C.
Side Frame
1 pc.
D.
Back Post
2 pcs.
M.
Seat Frame
1 pc.
Divider
Spring Washer
Flat Washer
45 pcs. (+1 extra)
45 pcs. (+1 extra)
M x
6 38
Tapered Bolt (medium)
8 pcs. (+1 extra )
888-680-7460
E.
Back Post
1 pc.
P.
Side Frame
1 pc.
O.
Refer to later page(s) of these
1 pc.
instructions for basket assembly.
M3x12
Wood Screw
for Hook
8 pcs. (+1 extra)
M x
6 70
Tapered Bolt (long)
4 pcs. (+1 extra )
I.
Back Panel
2 pcs.
Q.
Side Frame
1 pc.
R.
Basket
2 pcs.
Hook
4 pcs.
M3.5x8
Wood Screw
for Back Panel
12 pcs. (+1 extra)
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Homestyles 5053-49
Summary of Contents for Homestyles 5053-49
- Page 1 5053-49 Hall Tree IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed.
- Page 2 Assembly Instructions 2/7 IMPORTANT Ÿ Use a soft cloth between these parts and the floor. Ÿ Do not use power tools above 8 volts to assemble. Ÿ Do not tighten all the bolts until each part is properly assembled. Ÿ The unit must be level to work properly.
- Page 3 Assembly Instructions 3/7 STEP 3 Slide Back Panels (I) into position. Attach Top (A) and Shelf (K) to unit with Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway. Tighten all bolts used in Steps 1, 2 and 3. Flat Washer Spring Washer Head Cap Bolt...
- Page 4 Assembly Instructions 4/7 STEP 5 Attach Rails (J) and Seat Frame (M) to Side Frame (Q) with Flat Washers, Spring Washers, Head Cap Bolts and Tapered Bolts (medium), tightening bolts only halfway. (See Figure 4) Attach Side Frame (P) to unit with Flat Washers, Spring Washers, Head Cap Bolts and Tapered Bolts (medium), tightening bolts only halfway.
- Page 5 Assembly Instructions 5/7 Basket (R) Tapered Bolt (short) Clip STEP 7 Figure 5 Attach Basket Side (R2) to Basket Unit (R1) with clips and Tapered Bolts (short). (See Figures 5 and 6) Figure 6 STEP 8 Clip Tapered Bolt (short) Attach Basket Side (R2) to unit with clips and Tapered Bolts (short).
- Page 6 Assembly Instructions 6/7 Wood Screw for Hook Hook Tapered Bolt (long) STEP 9 Figure 7 Attach unit from Step 4 to unit from Step 6 with Tapered Bolts (long). Attach Hooks to unit by inserting Wood Screws for Hook into pre-drilled holes in unit, then tighten.
- Page 7 Assembly Instructions 7/7 IMPORTANT Ÿ To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly. STEP 10 Anchor in wall Wall Screw Pre-drilled hole Bracket on wall at top of unit Place unit at desired location.
- Page 8 CARE INSTRUCTIONS NEVER NEVER use glass cleaners on allow liquids to remain on furniture. finished furniture. Ammonia Absorption causes parts to warp chemically attacks the finish. and split and finishes to delaminate. Do not use power tools Do not place Do not write above 8 volts to assemble.
Need help?
Do you have a question about the 5053-49 and is the answer not in the manual?
Questions and answers