Advertisement
Quick Links
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
C.
B.
Side Panel
Side Panel
1 pc.
1 pc.
J.
Base
1 pc.
Hardware List
Hex Wrench
Adjustable Pin
1 pc.
16 pcs. (+1 extra)
3/4"
Small Hex Wrench
Flat Head Screw
1 pc.
12 pcs. (+1 extra)
Cartons 50
08-
942 and 5008 943 or 5009 943 are also needed for assembly.
Tool(s) required for assembly:
home
5008-941
Kitchen Island
D.
Middle Panel
1 pc.
K.
Back Panel
2 pcs.
Cam Lock
15 pcs. (+2 extra)
M6x35
Head Cap Bolt
20 pcs. (+1 extra)
-
Phillips screwdriver,
styles Customer Service: www.homestylesfurniture.com,
servicedesk@homestylesfurniture.com,
E.
Front Rail
1 pc.
F.
Front Rail
1 pc.
G.
Back Rail
1 pc.
L.
Back Upright
1 pc.
1/2"
Cam Lock Screw
Round Head Screw
15 pcs. (+1 extra)
4 pcs. (+1 extra)
Flat Washer
Magnet
8 pcs. (+1 extra)
2 pcs.
-
Level
Patent 8,584,600 B2
H.
Back Rail
1 pc.
I.
Shelf
4 pcs.
M.
Door
1 pc.
O.
Drawer
2 pcs.
Refer to later page(s) of these
instructions for drawer assembly.
3/4"
Round Head Screw
8 pcs. (+1 extra)
M4x25
Machine Screw
4 pcs.
888-680-7460
N.
Door
1 pc.
1"
Round Head Screw
16 pcs. (+1 extra)
Knob
4 pcs.
Advertisement
Related Manuals for Homestyles 5008-941
Summary of Contents for Homestyles 5008-941
- Page 1 5008-941 Kitchen Island IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed.
- Page 2 Assembly Instructions 2/9 IMPORTANT Ÿ Use a soft cloth between these parts and the floor. Ÿ Do not use power tools above 8 volts to assemble. Ÿ Do not tighten all the bolts until each part is properly assembled. Ÿ The unit must be level to work properly.
- Page 3 Assembly Instructions 3/9 STEP 3 Attach Middle Panel (D) to Back Rails (G), (H) and Back Upright (L) with Cam Locks. (See Figure 3) Slide Back Panels (K) into position. Attach Front Rails (E) and (F) to unit with Cam Locks. Cam Lock Figure 3 Cam Lock...
- Page 4 Assembly Instructions 4/9 Flat Washer Head Cap Bolt STEP 5 Attach Base (J) to unit with Cam Locks, Flat Washers and Head Cap Bolts. Tighten bolts with Hex Wrench. (See Figure 4) Cam Lock STEP 6 Figure 4 Turn unit to its upright position. Attach Post Assemblies (P) and (Q) to unit with Head Cap Bolts.
- Page 5 Assembly Instructions 5/9 3/4” Round Head Screw Knob Machine Screw STEP 7 Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 5) Note: Unit must be level to proceed. Insert 3/4” Round Head Screws into pre-drilled holes in back of unit, then tighten. Note: Unit must be level before tightening these screws.
- Page 6 Assembly Instructions 6/9 Adjustable Pin STEP 8 Insert Adjustable Pins into side panels and middle panel at desired level. Slide Shelves (I) into position. STEP 9 3/4” Flat Head Screw Place Top (A1) and Leaf Top (A2) upside down on a soft cloth. Attach Leaf Top (A2) to Top (A1) with 3/4”...
- Page 7 Assembly Instructions 7/9 Drawer (O) STEP 10 Attach Drawer Front (O1) and Drawer Back (O2) to Drawer Side (O3) with 1” Round Head Screws. Roller at back 1” Round Head Screw 1” Round Head Screw STEP 11 Slide Drawer Bottom (O5) into groove. Attach Drawer Side (O4) to unit with 1”...
- Page 8 Assembly Instructions 8/9 Flat Washer Head Cap Bolt STEP 13 Attach Top (A1) to unit with Flat Washers and Head Cap Bolts. Slide Drawers (O) into position.
- Page 9 Assembly Instructions 9/9 STEP 14 When leaf top is down, it should be oriented vertically. If it is not vertical and adjustment is desired, turn the adjuster on adjuster block on back rail. (See Figure ) 9 Adjuster Block Figure 9 Top Extension Instructions STEP 15 Lift up leaf top.
- Page 10 CARE INSTRUCTIONS NEVER NEVER use glass cleaners on allow liquids to remain on furniture. finished furniture. Ammonia Absorption causes parts to warp chemically attacks the finish. and split and finishes to delaminate. Do not use power tools Do not place Do not write above 8 volts to assemble.
- Page 11 5008 942 Kitchen Island IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble.
- Page 12 5008-943 Kitchen Island IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble.
Need help?
Do you have a question about the 5008-941 and is the answer not in the manual?
Questions and answers