Advertisement
Quick Links
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
A.
Top
1 pc.
B.
Shelf
2 pcs.
C.
Shelf
1 pc.
H.
Front Rail
2 pcs.
Hardware List
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Tool(s) required for assembly: Phillips screwdriver, Level, Pencil, Drill (8 volts or less), 3/8" Drill Bit
home
5053-106
Over the Commode Stand
D.
Side Frame
1 pc.
M6x16
Head Cap Bolt
32 pcs. (+1 extra)
Flat Washer
24 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,
servicedesk@homestylesfurniture.com,
E.
Side Frame
1 pc.
I.
Back Rail
2 pcs.
M3.5x40
Spring Washer
Wall Screw
32 pcs. (+1 extra)
2 pcs. (+1 extra)
Flat Washer (large)
Adjustable Pin
8 pcs. (+1 extra)
8 pcs. (+1 extra)
888-680-7460
F.
G.
Side Frame
Side Frame
1 pc.
1 pc.
Anchor
2 pcs. (+1 extra)
Bracket
2 pcs. (+1 extra)
Advertisement
Related Manuals for Homestyles 5053-106
Summary of Contents for Homestyles 5053-106
- Page 1 5053-106 Over the Commode Stand IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed.
- Page 2 Assembly Instructions 2/6 IMPORTANT Ÿ Use a soft cloth between these parts and the floor. Ÿ Do not use power tools above 8 volts to assemble. Ÿ Do not tighten all the bolts until each part is properly assembled. Ÿ The unit must be level to work properly.
- Page 3 Assembly Instructions / 3 6 Flat Washer Spring Washer Head Cap Bolt STEP 2 Attach Side Frame (E) to Side Frame (G) with Flat Washer, Spring Washer and Head Cap Bolt, tightening bolt only halfway. Attach unit to unit from Step 1 with Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway.
- Page 4 Assembly Instructions / 4 6 Flat Washer (large) Spring Washer Head Cap Bolt STEP 3 Attach Top (A) and Shelf (C) to unit with Flat Washers (large), Spring Washers and Head Cap Bolts, tightening bolts only halfway. Tighten all bolts used in all steps.
- Page 5 Assembly Instructions / 5 6 Adjustable Pin Figure 3 Figure 4 STEP 4 Turn unit to its upright position. Insert Adjustable Pins into unit at desired level. (See Figure 3) Place Shelves (B) into position. Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 4) Note: Unit must be level to work properly.
- Page 6 Assembly Instructions / 6 6 IMPORTANT Ÿ To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly. STEP 5 Place unit at desired location. Loosen slightly Head Cap Bolts attaching Brackets to unit.
- Page 7 CARE INSTRUCTIONS NEVER NEVER use glass cleaners on allow liquids to remain on furniture. finished furniture. Ammonia Absorption causes parts to warp chemically attacks the finish. and split and finishes to delaminate. Do not use power tools Do not place Do not write above 8 volts to assemble.
Need help?
Do you have a question about the 5053-106 and is the answer not in the manual?
Questions and answers