Advertisement
PowerCage 411 Enclosure • Setup Guide (Continued)
1.
Where applicable, remove as many blank plates
or previously installed boards from the rear of the
PowerCage Enclosure as necessary to accommodate the
number of new boards to be installed.
2.
Carefully slide the board into the slot, aligning the bottom
edge of the board with the left and right board mounting
slides on the bottom of the enclosure slot. Push the board
completely into the slot and finger-tighten the two top
screws while pushing in the screws to secure the board in
place (see figure 2).
3.
Repeat step 2 for all boards needing installation.
NOTE:
Cover all empty board slots; do not leave them
open. Securely fasten the screws for all boards and
blank panels.
Front Panel Features
A A A
C C C
215W
POWER SUPPLY
B B B B B B B
Figure 3.
PowerCage 411 FOX3 Front Panel
A
Power supply LEDs —
LED Color - State
Green - Solid
Red - Solid
Orange - Solid
Green - Blinking
Red - Blinking
Orange - Blinking
B
Power supplies — Connect power to IEC power connector 1 or 2 (see figure 1,
C
Fans — For power supplies.
D
Configuration port — If desired, connect a host device to the front panel USB mini-B port for configuring the enclosure.
NOTE:
This port allows communication to the enclosure and the boards.
E
LCD screen — The screen displays messages, menu information, and your selections (see
Adjustments
on page 3).
F
Reset button and LED — Pressing the Reset button sets various enclosure settings to the factory default values. The LED
lights green after pressing the Reset button (see the PowerCage 411 Series User Guide for details).
G
Navigation buttons —
•
MENU — Press MENU to access the PowerCage 411 menu system (see
•
NEXT — From each menu press NEXT to step through submenus (see
H
Navigation adjust knobs —
•
Horizontal — Turn the horizontal adjust knob to navigate the menu system (see
Adjustments).
•
Vertical — Turn the vertical adjust knob to navigate the menu system (see
2
C C C
CONFIG
E
D D D
E E E
Power Supply Status
Good
Failed
No AC power present
Good
Failed
No AC power present
B
A
IN
O U
T
IN
T
O U
T
O U
O P
B 2
.0
LO
U S
U T
B H
ID
-2 3
2
IN P
M I
U S
R S
H D
IN
D IO
B
G
A U
R x
T x
A
IN
T
O U
IN
T
O U
O U
T
O P
B 2
.0
LO
U S
U T
Align board and
-2 3
2
IN P
R S
M I
H D
R x
G
T x
slide into slot.
Figure 2.
Board Installation
A A A
ADJUST
MENU
NEXT
RESET
POWERCAGE 411
F F F
G G G
H H H
Fan Status
Both fans functional
Both fans functional
Both fans functional
Either fan not functional
Either fan not functional
Either fan not functional
A
on page 1).
Menus, Configuration, and
Menus, Configuration, and
Menus, Configuration, and
Menus, Configuration, and
B
A
IN
T
O U
IN
T
O U
O U
T
O P
B 2
.0
LO
U S
U T
ID
-2 3
2
IN P
B H
U S
R S
M I
H D
IN
D IO
A U
R x
G
T x
B
A
IN
T
O U
IN
T
O U
T
O U
O P
.0
B 2
LO
U S
ID
2
U T
B H
-2 3
IN P
R S
M I
U S
H D
IN
D IO
A U
G
R x
T x
Screws
(2 per board)
C C C
C C C
215W
POWER SUPPLY
B B B
Menus, Configuration, and
Adjustments).
Adjustments).
Adjustments).
Advertisement
