Table of Contents
Advertisement
Operation
Master/Slave Mode (Wired)
The Master/Slave mode allows a single LED Shadow 2 ILS product (the "master") to control the actions of
one or more LED Shadow 2 ILS products (the "slaves") without the need of a DMX controller. The master
product will be set to operate in either standalone mode or with the IRC-6, while the slave products will be
set to operate in slave mode. Once set and connected, the slave products will operate in unison with the
master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 4Ch shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select d 1.
4. Press <ENTER>.
5. Connect the DMX input of the first slave product to the DMX output of the master product.
6. Connect the DMX input of the subsequent slave products to the DMX output of the previous slave
product.
7. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to operate in standalone mode or with the IRC-6.
2. Make the master product the first product in the DMX daisy chain.
•
Configure all the slave products before connecting the master to the daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave operation
because the controller may interfere with the signals from the master.
•
Do not connect more than 31 slaves to the master.
Master/Slave Mode (D-Fi USB)
The D-Fi USB allows a single LED Shadow 2 ILS product (the "master") to control the actions of one or
more LED Shadow 2 ILS products (the "slaves") without the need of a DMX controller or DMX cables. The
master (transmitter) product will be set to operate in standalone mode or with the IRC-6, while the slave
(receiver) products will be set to operate in DMX mode. Once set and connected, the slave products will
operate in unison with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 4Ch shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to set the starting address to d 1.
4. Press <ENTER>.
5. Set the D-Fi USB to receive on a specific channel, 1–16.
6. Plug in the D-Fi USB.
7. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to operate in standalone mode.
2. Set the D-Fi USB to transmit on the D-Fi channel the slaves are receiving on.
3. Plug in the D-Fi USB.
•
All products must be set to the same DMX personality, DMX address, and D-Fi channel.
•
Configure all the slave products before configuring the master to transmit.
•
Never connect a DMX controller to a D-Fi channel configured for Master/Slave operation
because the controller may interfere with the signals from the master.
ILS Mode
ILS (Integrated Lighting System) provides 4 modes that synchronize with the GigBAR MOVE+ILS: Modes
1 and 3 synchronize with side 1 of the GigBAR MOVE+ILS, whereas modes 2 and 4 synchronize with side
2 of the GigBAR MOVE+ILS. When linked, effects will sync with the most similar effect on the selected side
of the GigBAR MOVE+ILS: Kinta effects will sync with one of the kintas, wash effects will sync with one of
the pars, etc. This product will synchronize with the par on the selected side of the GigBAR MOVE+ILS.
To set the LED Shadow 2 ILS to respond to an ILS signal:
1. Press <MENU> repeatedly until iLS shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select from iLS1 (side 1), iLS2 (side 2), iLS3 (side 1), or iLS4 (side 2).
4. Press <ENTER>.
LED Shadow 2 ILS User Manual Rev. 1
Page 11 of 15
Advertisement
Table of Contents
