Download Print this page

Transition Networks E-TBT-FRL-1007 User Manual

8-port 10base-t to fiber media converter

Advertisement

Quick Links

MEDIA CONVERTER TECHNICAL SPECIFICATIONS
Standards
IEEE 802.3
Case dimensions
17.0" x 7.5" x 1.7"
Environment
Temperature:
Humidity
Altitude
Warranty
2 years
10BASE-T CABLE SPECIFICATIONS
Required: Category 3; Recommended: Category 5 wire. Use either shielded twisted
pair (STP) or unshielded twisted pair (UTP). DO NOT USE FLAT/SILVER SATIN WIRE.
Category 3:
Gauge
Attenuation
Differential Characteristic Impedance
Category 5:
Gauge
Attenuation
Differential Characteristic Impedance
Maximum Cable Distance:
10BASE-FL CABLE SPECIFICATIONS
Fiber Optic Cable Recommended:
Optional:
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Maximum Cable Distance:
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC
TELEPHONE NETWORK. Failure to observe this caution could result in damage to the
public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten verstösst
gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur Angleichung der
Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen einschliesslich der
gegenseitigen Anerkennung ihrer Konformität.
Compliance Information
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at the user's own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio
interference regulations of the Canadian Department of Communications.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
Copyright Restrictions
© 1996 TRANSITION Networks Inc. All rights reserved. No part of this work may be reproduced or used in any form
or by any means – graphic, electronic, or mechanical – without written permission from TRANSITION Networks Inc.
Trademark Notice
(432mm x 191mm x 43mm)
0-50°C (32° to 122° F )
10-90%, non condensing
0-10,000 feet
24 to 22 AWG
28 dB/1000' @ 10 MHz
100
±10% @ 10 MHz
24 to 22 AWG
20 dB/1000' @ 10 MHz
100
±10% @ 10 MHz
100 meters (330 feet)
62.5 / 125 µm multimode fiber
100 / 140 µm multimode fiber
85 / 125 µm multimode fiber
50 / 125 µm multimode fiber
Average power:
-15.0 dBm
Peak power: -12.0 dBm ±1dBm
Average sensitivity:
-27.4 dBm
-10
Bit error rate:
10
2000 meters (6500 feet)
8-Port 10BASE-T to Fiber

Media Converter

E-TBT-FRL-1007
USER'S GUIDE
The 8-Port 10BASE-T to Fiber Media Converter provides eight (8) separate
and independent 10BASE-T to fiber media converters in a convenient
19-inch rack mountable chassis. NOTE: The media converter supports
10Mb/s speeds only.
Transition Networks 8 Port 10BaseT to Fiber Media Converter
Converter 1
Converter 2
Converter 3
Converter 4
RJ Link
RJ Link
RJ Link
RJ Link
FL Link
FL Link
FL Link
FL Link
RJ RX
RJ RX
RJ RX
RJ RX
RX
TX
RX
TX
RX
TX
RX
Power
FL RX
FL RX
FL RX
FL RX
10BaseT
10BaseT
10BaseT
10BaseT
INDICATORS
(RJ, FL) Link
Steady green LED
indicates port is
receiving link
signal.
(RJ, FL) RX
Flashing green
LED indicates
port is receiving
data.
Power
Steady green LED indicates 8-Port 10BASE-T to
Fiber Media Converter is powered by AC current.
CONNECTORS
10BASE-T
RJ-45 connector
10BASE-FL
TX, RX ST type connectors (SMA type available
upon request)
Power
Female 3-prong AC connector
Minneapolis, MN 55344 USA
Converter 5
Converter 6
Converter 7
Converter 8
RJ Link
RJ Link
RJ Link
RJ Link
FL Link
FL Link
FL Link
FL Link
RJ RX
RJ RX
RJ RX
RJ RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
FL RX
FL RX
FL RX
FL RX
10BaseT
10BaseT
10BaseT
10BaseT
Converter 1
RJ Link
FL Link
RJ RX
RX
TX
Power
FL RX
10BaseT
(1-8)

Advertisement

loading
Need help?

Need help?

Do you have a question about the E-TBT-FRL-1007 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Transition Networks E-TBT-FRL-1007

  • Page 1: Media Converter

    ±10% @ 10 MHz ±10% @ 10 MHz The 8-Port 10BASE-T to Fiber Media Converter provides eight (8) separate and independent 10BASE-T to fiber media converters in a convenient 19-inch rack mountable chassis. NOTE: The media converter supports 10Mb/s speeds only.
  • Page 2: Troubleshooting Suggestions

    Check RJ connectors and UTP cables for proper connection and pin assignment. (See below.) NOTE: In the installation drawing, connections between the switch and the Media Converters are configured as straight through; the connection between the Media Converter and the terminal is configured as crossover.