Related Manuals for Dahua ITC952-AU3F-L
Summary of Contents for Dahua ITC952-AU3F-L
- Page 1 All-in-one Enforcement Camera User's Manual ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.3...
-
Page 2: Foreword
This manual introduces the structure, installation, system networking, and initial configurations of the all-in-one enforcement camera (hereinafter referred to as the "Camera"). Models All-in-one Enforcement HD Intelligent Enforcement Pixel Camera Camera ITC952-AU3F-L (ZF1640) ITC952-AF3F ITC952-AU3F-IRL7 (ZF1640) 11 MP ITC952-AF3F-IR7 ITC952-AU3F-IRL8 (ZF1640) ITC952-RU2D-IRL7 (ZF1640) ITC952-RF2D-IR7... - Page 3 User's Manual Revision History Version Revision Content Release Time V1.0.3 Updated manual format and cybersecurity contents. November 2021 V1.0.2 Updated manual format. February 2021 V1.0.1 Added camera models and updated manual font. January 2021 V1.0.0 First release. April 2020 Privacy Protection Notice As the device user or data controller, you might collect the personal data of others such as their face, fingerprints, and license plate number.
-
Page 4: Important Safeguards And Warnings
User's Manual Important Safeguards and Warnings This section introduces content covering the proper handling of the device, hazard prevention, and prevention of property damage. Read carefully before using the device, comply with the guidelines when using it, and keep the manual safe for future reference. Transportation Requirements Transport the device under allowed humidity and temperature conditions. - Page 5 User's Manual ● Use the device under allowed humidity and temperature conditions. ● Do not drop or splash liquid onto the device, and make sure that there is no object filled with liquid on the device to prevent liquid from flowing into it. ●...
-
Page 6: Table Of Contents
User's Manual Table of Contents Foreword ........................................I Important Safeguards and Warnings ............................III 1 Overview ........................................1 1.1 Introduction ....................................1 1.2 Features ......................................1 1.3 Functions ....................................... 1 2 Device Structure ....................................5 2.1 Structure ......................................5 2.2 Terminal ......................................6 2.3 Camera ...................................... - Page 7 User's Manual Appendix 1 Cybersecurity Recommendations ........................27...
-
Page 8: Overview
User's Manual 1 Overview 1.1 Introduction Designed with industry-specific GS-CMOS image sensor and high-performance AI processor, and integrated with deep learning algorithms, the Camera enjoys 4K high definition and ultra-high video fluency. It collects real-time data of traffic conditions, and captures clear images of vehicles at day and night. - Page 9 User's Manual Picture Cutout With sufficient light supplement of flashing light, when capturing one vehicle, the Camera can also cut out the plate number part of the snapshot. Camera in ANPR mode can even cut out the face picture of people in the front. Intelligent Recognition ●...
- Page 10 User's Manual Traffic Flow Statistics Traffic flow statistics of lane is realized through connection to traffic signal controller or camera. Supports uploading statistics data to corresponding platform server. Snapshot ● Supports snapshot and coding of picture. ● Supports watermark encryption to prevent tampering. ●...
- Page 11 User's Manual Auxiliary Functions ● Watermark encryption of video image coding to prevent tampering. ● Real-time display of system resource information and running status. Support log function. ● Signal control and output of strobe, flashing light, and continuous light. ● GPS positioning.
-
Page 12: Device Structure
User's Manual 2 Device Structure 2.1 Structure Protective cover of the Camera includes power supply, terminal, and HD camera. The structure is taken as an example. Different devices might have different components. Figure 2-1 Structure Figure 2-2 Structure (2) Figure 2-3 Structure (3) -
Page 13: Terminal
User's Manual Table 2-1 Protective cover Description Description Camera Power Terminal Built-in LED illuminator 2.2 Terminal The two typical kinds of terminals are shown in the following two figures. Different devices might have different types of terminals. Figure 2-4 Terminal (1) Table 2-2 Description of terminal (1) Name Description... - Page 14 User's Manual Name Description RS–485_B1 AC 220V live wire AC 220V neutral wire AC 220V earth wire Figure 2-5 Terminal (2) Figure 2-6 Terminal (3) Table 2-3 Description of terminal (2) Name Description Flashing light 1 triggers output F1+ Flashing light 1 triggers output F1- Flashing light 2 triggers output F2+ Flashing light 2 triggers output F2- Flashing light 3 triggers output F3+...
-
Page 15: Camera
User's Manual Name Description Flashing light 7 triggers output F7+ Flashing light 7 triggers output F7- RS485-A1 RS485-B1 12+ DC 12- DC 220 VAC live wire 220 VAC neutral wire 220 VAC earth wire 2.3 Camera 2.3.1 Rear Panel Figure 2-7 Rear panel Table 2-4 Rear panel ports Port Function... - Page 16 User's Manual Port Function Restore to factory settings. When the Camera runs normally (the power indicator light is blue), press and RESET Reset button hold the RESET button for at least 5 seconds, and the Camera restores to factory defaults. Displays the activity status of the Camera.
-
Page 17: Side Panel
User's Manual Port Function Connects TF card. Before hot swapping the TF card, go to Setup > TF card port Storage > Destination > Local on the web page of the Camera, and click Hot Swap. 2.3.2 Side Panel Figure 2-8 Side panel dimensions (mm (inch)) 2.3.3 Front Panel Figure 2-9 Front panel dimensions (mm (inch)) 2.4 LED Illuminator... - Page 18 ● Do not use the illuminator in water. ● Do not hit the illuminator and pull its cable. DHI-ITC952-AU3F-L, DHI-ITC352-AU3F-L These two models are designed with 3 white light LED illuminators. Figure 2-10 Dimensions (mm [inch]) DHI-ITC952-AU3F-IRL7, DHI-ITC952-AU3F-IRL8, DHI-ITC352-AU3F-IRL7, DHI-ITC352-AU3F-IRL8 These models are designed with 8 IR illuminators.
- Page 19 User's Manual Figure 2-12 Dimensions (mm [inch]) DHI-ITC952-RU2F-BD No illuminators.
-
Page 20: Installation
User's Manual 3 Installation When you open the package, check the Camera and accessories against the checklist. After confirming the package, install the Camera by following the instructions in the manual. You need to manually install the accessories such as lens, TF card, cables, and corrugated pipe. For other accessories and connections, install according to the actual condition. -
Page 21: Removing The Lens
User's Manual 3.1.2 Removing the Lens Figure 3-2 Removing lens Step 1 Unplug the cable from the lens mount. Step 2 Turn the lens to counter-clockwise until the lens is removed. Step 3 Install the protective covers of sensor and lens to prevent them from being spotted. 3.2 Installing TF Card This section takes some models as the example, and might differ from the actual model. -
Page 22: Connecting Cable
User's Manual Figure 3-4 Removing TF card 3.3 Connecting Cable You need to use a 2.0 mm screwdriver to connect cables. ● Avoid copper wire exposure when connecting the power cord. With 220 V power supply, copper wire exposure might cause electric leakage, and thus bringing personal injury. ●... -
Page 23: Removing The Cable
User's Manual the screwdriver vertically to loosen and expose the metal sheet of the circular slot. Step 2 Insert the cable into the circular slot. Step 3 Remove the screwdriver, and the cable installation is finished. 3.3.2 Removing the Cable Step 1 Insert the screwdriver into the square slot corresponding to the connecting cable. -
Page 24: System Network
User's Manual 4 System Network As the center of traffic surveillance system, the Camera can record videos of different surveillance scenes, and transmit video data to controller, central server or storage device through network. Figure 4-1 System network... -
Page 25: Configuration
User's Manual 5 Configuration After mounting the Camera, power on the Camera, connect it to the network and make initial settings, then you can successfully log in to the web page of the Camera. For more configurations, see the web operation manual of the HD intelligent enforcement camera. 5.1 Initialization The Camera is delivered in uninitialized status. - Page 26 User's Manual Step 6 On the Online Upgrade page, you can cancel selecting Auto-check for updates (selected by default). Figure 5-2 Login Step 7 Click Confirm. Step 8 On the login page, enter the username (admin) and the password that you set. On the Config Guide page, set the business type and road mode.
-
Page 27: Initializing Cameras In Batches With Configtool
It is ideal to initialize cameras in batches and modify their default IP addresses by using ConfigTool.To acquire ConfigTool, go to Dahua official website, and then select Support > Download Center > Tools > Maintenance Tools. Find ConfigTool, and download and install it... - Page 28 User's Manual according to onscreen instructions. This section takes ConfigTool 4.07.0 as the example. Different versions might have different pages. Step 1 After installing ConfigTool, open the tool. , and then click Search setting. Step 2 Click Figure 5-7 Modify IP Step 3 Enter the start IP address and end IP address of the network segment in which you want to search devices, and then click OK (default IP address of the Camera: 192.168.1.108).
-
Page 29: Modifying Ip Addresses In Batches With Configtool
User's Manual Step 8 Select the options according to your needs, and then click OK. The Initialization page is displayed after initialization is completed. Click the success icon Step 9 ( ) or the failure icon ( ) for the details. Step 10 Click Finish. -
Page 30: Updating The Camera With Configtool
User's Manual After initializing cameras in batches, you can easily go to the camera login page by clicking on the ConfigTool page. See Figure 5-11. In this case, you do not need to enter the IP address of each camera when login. Step 2 Enter the IP address of the Camera in the browser address bar, and press the Enter key. - Page 31 User's Manual Step 1 Open ConfigTool. Step 2 Click Figure 5-12 Upgrade Step 3 Select the ITCs (cameras) that you want to update. ● Update one ITC: Click Browse corresponding to the ITC to be updated. ● Update ITCs in batches: Select the ITCs to be updated, and then click Batch Upgrade. Step 4 Select the update file.
- Page 32 User's Manual ● Update one ITC: Click Upgrade, and the system starts updating. You can view the update progress. ● Update ITCs in batches: Click OK, and the system starts updating. If the camera is disconnected during updating, as long as the ConfigTool stays on the update page, the update will resume when the connection is restored.
-
Page 33: Faq
User's Manual 6 FAQ Question Solution Device error, unable to start Press and hold Reset button for 5 seconds to restore the Camera or operate normally to factory settings. Stop recording and image capturing, and then wait for at least TF card hot swapping 15 seconds before removing the TF card. - Page 34 IP video surveillance is not immune to cyber risks, but taking basic steps toward protecting and strengthening networks and networked appliances will make them less susceptible to attacks. Below are some tips and recommendations from Dahua on how to create a more secured security system.
- Page 35 User's Manual 1024–65535, reducing the risk of outsiders being able to guess which ports you are using. 6. Enable HTTPS We suggest you to enable HTTPS, so that you visit Web service through a secure communication channel. 7. MAC Address Binding We recommend you to bind the IP and MAC address of the gateway to the equipment, thus reducing the risk of ARP spoofing.
- Page 36 User's Manual ● Enable IP/MAC address filtering function to limit the range of hosts allowed to access the device. More information Please visit Dahua official website security emergency response center for security announcements and the latest security recommendations.
- Page 37 User's Manual...
Need help?
Do you have a question about the ITC952-AU3F-L and is the answer not in the manual?
Questions and answers