Related Manuals for Planet IPOE-E302
Summary of Contents for Planet IPOE-E302
- Page 1 Industrial IP67 1-Port 802.3bt PoE++ to 2-Port 802.3at/bt Gigabit PoE Extender IPOE-E302 User's Manual...
-
Page 2: Table Of Contents
3.2 Connecting Waterproof Cable Kit to the Outdoor PoE Extender ..6 3.3 Wall-mount Installation ..............9 3.4 Grounding the Device ..............10 3.5 Connecting IPOE-E302 to PSE ............11 3.6 Connecting IPOE-E302 to PD ............11 4. Power over Ethernet Budget ..............13 5. Product Specifications ................. -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET Industrial IP67 1-port 10/100/1000T 802.3bt PoE++ to 2-port 10/100/1000T 802.3at/bt PoE++ Extender, IPOE-E302. In the following sections, the term “Outdoor PoE Extender” means the IPOE-E302. Open the box of the Industrial PoE Extender and carefully unpack it. The box... -
Page 4: Hardware Introduction
This section describes the functionalities of the Outdoor PoE Extender’s components. 2.1 Product Outlook LNK/ LNK/ IPOE-E302 LNK/ Unit: mm Figure 2-1: IPOE-E302 product outlook 2.2 802.3bt PoE++ Input Port Figure 2-2 shows the PoE++ input port side of the IPOE-E302 Figure 2-2: IPOE-E302 PoE++ Input Port Side... -
Page 5: 802.3At/Bt Poe+ Output Port
2.3 802.3at/bt PoE+ Output Port Figure 2-3 shows the two PoE+ ouput ports side of the IPOE-E302. Figure 2-3: IPOE-E302 PoE++ Output ports side 2.4 LED Indicators Color Function Lights to indicate the port is linked up at 10/100/1000Mbps. LNK/ACT Green Blinks to indicate that the IPOE-E302 is actively sending or receiving data over that port. -
Page 6: Installation
3. Installation This section describes how to install the Outdoor PoE Extender and make connections to it. Please read the following sections and perform the procedure in the order being presented. 3.1 Installing Cable Gland with RJ45 UTP Cable The cable gland consists of the following A. - Page 7 Step 2: Plug the RJ45 connector into the connector of the PoE++ In port. Step 3: Insert the sealing insert into the cable gland body. Step 4: Attach the clamping nut to the cable gland to complete the cable assembly. Make sure the clamping nut is tightly attached to the cable gland body and the sealing insert is squeezed tightly.
- Page 8 Step 5: Repeat Steps 1 to 4 for two PoE++ Out ports.
-
Page 9: Wall-Mount Installation
4. Never use any waterproof cable gland that is not purchased from PLANET or doesn’t have the same dimensions of the IPOE-E302; it will damage the device permanently. 3.3 Wall-mount Installation To install the Outdoor PoE Extender on the wall, please follow the instructions described below. -
Page 10: Grounding The Device
Step 3: Use a screwdriver to screw them into the wall. 3.4 Grounding the Device Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device. Earth Ground EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY. -
Page 11: Connecting Ipoe-E302 To Pse
802.3bt PoE Switch (PSE) Step 2: The PSE delivers both Ethernet Data and PoE power over UTP cable to the IPOE-E302 and the “LAN” LED will be lit steadily. 1. If the LED is not lit, please check the remote PSE or the cable connecting to a PC or a network device to see if the cable is correct. - Page 12 DC voltage to the Cat5e/6 cable and transfer data and power simultaneously between the PSE and PD. Step 3: Once the IPOE-E302 detects the existence of an IEEE 802.3at/bt device or Ethernet device, the LAN LED indicator will be lit steadily, showing it is providing power.
-
Page 13: Power Over Ethernet Budget
2. The aggregated power consumption will be below 60 watts if with PoE+ PSE. Power over Ethernet Capability With different distance and different PoE input source, it will inflect the PoE output capability. Please refer to the table below. PoE Output Capacity (A): Distance (B): Distance 802.3bt PoE Switch (PSE) IPOE-E302 (C): Watts... - Page 14 When PoE Switch (PSE) Output is DC 52V. A (Distance) B (Distance) C (Watts) 52.7W 50.1 W 49.6W 100M 44.9W 100M 100M 37.6W 100M 36.5W 100M 100M 34.6W When PoE Switch (PSE) Output is DC 54V. A (Distance) B (Distance) C (Watts) 52.9W 50.8W...
- Page 15 When PoE Switch (PSE) Output is DC 56V. A (Distance) B (Distance) C (Watts) 54.1W 53.4W 52.1W 100M 47.4W 100M 51.8W 100M 49.7W 100M 48.2W 100M 100M 46.7W The table list shown here is for your reference only. The actual performance should be related to your environment.
-
Page 16: Product Specifications
5. Product Specifications Model IPOE-E302 Hardware Specifications PoE in Port - 1 x 10/100/1000BASE-T Ethernet with 802.3bt PoE++ “Data + DC” in - Auto MDI/MDI-X, auto-negotiation RJ45 connector Network Connector PoE out Port - 2 x 10/100/1000BASE-T Ethernet with IEEE 802.3at/bt PoE++ “Data + DC” out... - Page 17 Power over Ethernet PoE in Port - IEEE 802.3bt PoE++ Type 4 standard PD - IEEE 802.3bt PoE++ Type 3 standard PD PoE Standard - IEEE 802.3at PoE+ end-span/mid-span PD Per PoE out Port IEEE 802.3bt PoE++ end-span/mid-span PSE PoE in Port 52~57V DC, max.
- Page 18 Environment Temperature: -40 ~ 75 degrees C Operating Relative Humidity: 5 ~ 95% (non-condensing) Temperature: -40 ~ 85 degrees C Storage Relative Humidity: 5 ~ 95% (non-condensing)
-
Page 19: Customer Support
6. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and user’s manual on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team.
Need help?
Do you have a question about the IPOE-E302 and is the answer not in the manual?
Questions and answers