4K HDR HDMI Over HDBaseT TX/RX Kit AT-HDR-EX-70C-KIT The Atlona AT-HDR-EX-70C-KIT is an HDBaseT transmitter/receiver kit for high dynamic range (HDR) formats. The kit is HDCP 2.2 compliant and supports 4K/UHD video @ 60 Hz with 4:4:4 chroma sampling, as well as HDMI data rates up to 18 Gbps. The HDR-EX-70C-KIT provides transmission of HDMI, as well as bidirectional IR and RS-232 control signals up to 230 feet (70 meters) for 1080p video, and up to 130 feet (40 meters) for 4K HDR over CAT6a/7 cable.
Page 3
Installation Guide AT-HDR-EX-70C-KIT Panel Descriptions AT-HDR-EX-70C-TX AT-HDR-EX-70C-RX POWER POWER 1. LINK 2. FW 3. TEST 4. 5V LOCK TEST UTILITY LINK LINK RX TX RX TX DC 48V RS-232 IR IN IR OUT HDBaseT OUT HDMI IN RS-232 IR IN IR OUT HDBaseT IN HDMI OUT...
Installation Guide AT-HDR-EX-70C-KIT RS-232 A 3-pin captive screw connector for RS-232 has been included. Pin out will be determined by the RS-232 cable and connect as RX (receive), TX (transmit) and (Ground). Two captive screw connectors for IR have been included. A 4-pin connector for the transmitter and a 3-pin connector for the receiver.
Installation Guide AT-HDR-EX-70C-KIT Mount the unit using the oval-shaped holes, on each mounting bracket. If using a drywall surface, a #6 drywall screw is recommended. - R X X - 7 R - E - H D L I N NOTE: Mounting brackets can also be inverted to mount the unit under a table or other flat surface.
Installation Guide AT-HDR-EX-70C-KIT Connection Diagram Automation Control System HDR UHD/HD Display CT OR RE SE 48 V AT-JUNO-451 -4 51 AT-HDR-EX-70C-RX A T- -2 32 TI C B as 23 2 R S- C -R X- 70 R -E -H D W ER AT-HDR-EX-70C-TX LI N...
Page 7
Installation Guide AT-HDR-EX-70C-KIT UTILITY AT-HD POWE The utility port and dial are used for updating firmware and 5V 1. LINK lock. Use the Dial to switch between modes. 2. FW 3. TEST 4. 5V LOCK TEST UTILITY LINK Mode 1: Link This is the default position of the dial and puts the unit into normal operation.
Installation Guide AT-HDR-EX-70C-KIT Updating Firmware Download the firmware .zip file from the firmware tab located at http://www.atlona.com/ AT-HDR-EX-70C-KIT. Extract the firmware, from the archive file, to the Windows desktop or other folder. Make sure the included 48 V DC power supply is connected to the transmitter and that an Ethernet cable is connected between the HDBaseT OUT and HDBaseT IN ports on the transmitter and receiver, respectively.
Page 12
Control and PoE Introduction The Atlona AT-HDR-EX-70C-KIT is an HDBaseT transmitter/receiver kit for high dynamic range (HDR) formats. The kit is HDCP 2.2 compliant and supports 4K/UHD video @ 60 Hz with 4:4:4 chroma sampling, as well as HDMI data rates up to 18 Gbps.
4K HDR HDMI over HDBaseT TX/RX ™ with Control and PoE Key Features 4K/UHD capability @ 60 Hz with 4:4:4 chroma sampling, plus support for HDR formats • Compatibility with new and emerging 4K/UHD and HDR-capable sources and displays. • Compatible with 4K HDR10 @ 60 Hz and Dolby®...
Page 14
4K HDR HDMI over HDBaseT TX/RX ™ with Control and PoE Connection Diagram Automation Control System UHD Display CT OR RE SE 48 V AT-JUNO-451 O -4 AT-HDR-EX-70C-RX AT -J -2 32 TI C B as 23 2 R S- C -R X- 70 R -E...