Related Manuals for Panduit ATLONA Omega AT-OME-SR21
Summary of Contents for Panduit ATLONA Omega AT-OME-SR21
- Page 1 Omega 4K/UHD ™ HDBaseT Transmitters and Scaler Receiver for HDMI with USB Solutions Setup and Configuration Guide AT-OME-SR21 Atlona Setup AT-OME-EX-TX Guide AT-OME-EX-TX-WP/-E...
- Page 2 Version Information Version Release Date Notes Jan 2020 Initial Release SR21 and OME Transmitters Setup...
-
Page 3: Table Of Contents
Table of Contents Introduction Installation AT-OME-SR21 AT-OME-EX-TX Connection Configuration Control SR21 and OME Transmitters Setup... -
Page 4: Introduction
Introduction This guide provides a base for setting up and configuring a AT-OME-SR21 when used with an OME-EX transmitter (TX or TX-WP). BluRay Player Laptop L IN V IC AT-OME-EX-TX E -S -O M 2 4 V IP M R S -2 S E T E -S -O M... -
Page 5: Installation
Installation AT-OME-SR21 The AT-OME-SR21 includes two mounting brackets and four mounting screws, which can be used to attach the unit to any flat surface. 1. Remove the top 2 case screws on the side of the unit. 2. Align the mounting brackets to the side of the units. 3. -
Page 6: At-Ome-Ex-Tx
Installation AT-OME-EX-TX The AT-OME-EX-TX provides two mounting brackets, which can be used to attach the unit to any flat surface. Use the two enclosure screws, on the sides of the unit to attach the mounting brackets. 1. Remove the top 2 case screws on the side of the unit. 2. -
Page 7: Connection
Connection 1. Connect the sources to the input ports on the OME-EX-TX and OME-SR21. 2. Connect an 568B terminated category cable to the HDBaseT output of the OME-EX-TX and the HDBaseT input of the OME-SR21. 3. Connect an HDMI cable from the SR21’s HDMI output port to an HDMI display. 4. - Page 8 Connection 8. *Optional* Connect a network switch to one of the LAN ports on the SR21 or the LAN port of the EX transmitter, for IP control, system configuration, or Ethernet routing. 9. *Optional* Connect a second Ethernet cable from one of the LAN ports of the SR21 to the local display to pass through Ethernet.
-
Page 9: Configuration
Configuration Configuration will be done through the webGUI. By default the unit will be set to DHCP mode and receive an IP address from the DHCP server. If there is no DHCP server, press and hold the IP MODE button for 5 seconds. The LED will blink 3 times when set to static. The PC connecting to the unit will need to be set to the same IP range as the unit. - Page 10 Configuration EDID and Scaling EDID The SR21 will have EDID on pass through by default. To change the settings on this, go to the EDID page. 1. Select EDID from the top menu. 2. Select the internal or saved EDID from the drop down menu next to the corresponding input port. 3.
- Page 11 Configuration NOTE: Based on the selection from the drop down menu, the scaler will adjust not only resolution but frame rate as well. All VESA resolutions will output at 60Hz when using the scaler. 3. Select Aspect Ratio, Overscan options, and Picture options.
- Page 12 Configuration USB Switching The SR21 will have the USB host switch to the most recently connected host device by default. To change this setting, go to the USB page. 1. Select USB from the top menu. 2. Select the USB Host option that works best. Follow USB - Assigns the USB devices to follow the most recently connected Host (e.g.
- Page 13 Configuration Audio The SR21 can mute/unmute output audio, as well as adjust levels. If no levels need to be adjust, skip these steps. 1. Select Audio from the top menu. 2. Adjust the Audio options as needed. Output Audio HDMI / L/R Enable - Unmutes the audio output signal, allowing audio to pass through the outputs. HDMI / L/R Disable - Mutes the audio output signal of the outputs.
-
Page 14: Control
Control The SR21 has the ability to control the display with CEC, RS-232, and TCP/IP and a secondary device by relay. Each can be triggered through the webGUI buttons or RS-232 and IP commands. By Default, CEC will be set as the control type. 1. - Page 15 Control 4. Select Display from the top menu. 5. Set the Auto power off parameters. Defaults is set to turn the display off after 15 seconds of signal loss and to wait 10 seconds before any more commands are sent to the display. The display will auto turn on as soon as a signal is received and all timers have expired.
- Page 16 Control TCP/IP The SR21 has the ability to control the display by TCP/IP commands. These commands can be triggered/tested from the webGUI. 1. Select Display from the top menu. 2. Set the Auto power off parameters. Defaults is set to turn the display off after 15 seconds of signal loss and to wait 10 seconds before any more commands are sent to the display.
- Page 17 Control Relay The SR21 has the ability to control a secondary device using a relay. By default the relay will change states based on the display’s power status. To change this setting, go to the System page. 1. Select System from the top menu. 2.
- Page 18 Toll free US International atlona.com 877.536.3976 41.43.508.4321 • • © 2019 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered trademarks are the property of their respective owners. Pricing, specifications and availability subject to change without notice.