GO-5000M-USB-UV User Manual (Ver. 1.1) Table of Contents Table of Contents Table of Contents About Technical Note Notice/Warranty Notice Warranty Certifications CE Compliance Warning Supplement Usage Precautions Notes on Cable Configurations Notes on Attaching the Lens Phenomena Specific to CMOS Image Sensors...
Page 3
GO-5000M-USB-UV User Manual (Ver. 1.1) Table of Contents ⑤ AC Adapter (Power Supply) (If Necessary) Step 3: Verify Camera Operation Step 4: Verify the Connection between the Camera and PC Step 5: Change the Camera Settings Step 6: Adjust the Image Quality...
Page 4
GO-5000M-USB-UV User Manual (Ver. 1.1) Table of Contents Trigger Control Normal Continuous Operation Timed Mode Trigger Width Mode RCT (Reset Continuous Trigger) Mode Video Send Mode Sequence Mode Trigger Sequence Mode Timing Sequence Index Table (Default) Descriptions of Index Table Parameters...
Table of Contents About Technical Note Some additional technical information is provided on the JAI website as Technical Notes. In this manual, if a technical note is available for a particular topic, the above icon is shown. Please refer to the following URL for Technical notes.
The material contained in this manual consists of information that is proprietary to JAI Ltd., Japan, and may only be used by the purchasers of the product. JAI Ltd., Japan makes no warranty for the use of its product and assumes no responsibility for any errors which may appear or for damages resulting from the use of the information contained herein.
GO-5000M-USB-UV User Manual (Ver. 1.1) Notice/Warranty connected. Consult the dealer or an experienced radio/TV technician for help. Warning Changes or modifications to this unit not expressly approved by the party responsible for FCC compliance could void the user’s authority to operate the equipment.
GO-5000M-USB-UV User Manual (Ver. 1.1) Notice/Warranty Supplement The following statement is related to the regulation on “Measures for the Administration of the Control of Pollution by Electronic Information Products “, known as “China RoHS“. The table shows contained Hazardous Substances in this camera.
GO-5000M-USB-UV User Manual (Ver. 1.1) Usage Precautions Usage Precautions Notes on Cable Configurations The presence of lighting equipment and television receivers nearby may result in video noise. In such cases, change the cable configurations or placement. Notes on Attaching the Lens...
GO-5000M-USB-UV User Manual (Ver. 1.1) Usage Precautions Phenomena Specific to CMOS Image Sensors The following phenomena are known to occur on cameras equipped with CMOS image sensors. These do not indicate malfunctions. Aliasing: When shooting straight lines, stripes, and similar patterns, vertical aliasing (zigzag distortion) may appear on the monitor.
GO-5000M-USB-UV User Manual (Ver. 1.1) Features Features This camera is an industrial progressive scan camera equipped with a Type 1 global shutter CMOS image sensor with 5.2 effective megapixels (2560 × 2048). This CMOS image sensor has sensitivity in the UV region. The unit is compact and lightweight in design and is equipped with USB3 Vision interface.
Page 12
GO-5000M-USB-UV User Manual (Ver. 1.1) Features Blemish compensation HDR (High Dynamic Range) function C-mount for lens mount - 12 -...
GO-5000M-USB-UV User Manual (Ver. 1.1) Parts Identification Parts Identification ① Lens Mount (C-Mount) ② USB 3.0 Connector ③ POWER/TRIG LED ④ DC IN/TRIG Connector (6-Pin Round) ⑤ Camera Locking Screw Holes (M3, 3mm depth) ① Lens Mount (C-Mount) Mount a C-mount lens, microscope adapter, etc. here.
GO-5000M-USB-UV User Manual (Ver. 1.1) Parts Identification ③ POWER/TRIG LED Indicates the power or trigger input status. Status Lit amber Camera initializing Lit green Camera in operation During operation in trigger mode, trigger signals are being input. Blinking Note: The blinking interval is not related to the actual input interval of the external green trigger.
Read this section to learn how the camera connects to devices and accessories. The preparation process is described below. Step 1: Install the Software (First Time Only) Install the software for configuring and controlling the camera (eBUS SDK for JAI) on the computer. Step 2: Connect Devices Connect the lens, USB cable, AC adapter, computer, and other devices.
When using the camera for the first time, install the software for configuring and controlling the camera (eBUS SDK for JAI) on the computer. Note: When you install eBUS SDK for JAI, eBUS Player for JAI will also be installed. 1. Download the eBUS SDK for JAI from the JAI website (https://www.jai.com/support-software/jai-...
GO-5000M-USB-UV User Manual (Ver. 1.1) Preparation ① Lens C-mount lenses with lens mount protrusions of 10 mm or less can be attached. To prevent vignetting and to obtain the optimal resolution, use a lens that will cover the image sensor size.
GO-5000M-USB-UV User Manual (Ver. 1.1) Preparation ③ USB 3.0 Cable Connect a USB cable to the USB 3.0 connector. Caution: The camera is equipped with a USB 3.0 compatible Micro B connector. Although this connector includes USB 2.0 connectors, the camera does not support use of USB 2.0.
③ POWER/TRIG LED section. Step 4: Verify the Connection between the Camera and PC Verify whether the camera is properly recognized via Control Tool. 1. Launch eBUS Player for JAI eBUS Player for JAI startup screen appears. - 19 -...
Page 20
GO-5000M-USB-UV User Manual (Ver. 1.1) Preparation 2. Select the camera you want to configure. Click the Select / Connect button. 3. The connected camera is listed. Please select one camera and click OK. - 20 -...
Page 21
GO-5000M-USB-UV User Manual (Ver. 1.1) Preparation 4. Check that the settings of the selected camera are displayed. 5. Click the Device control button. The screen shown below will be displayed. In this window, you can adjust various settings of the camera.
GO-5000M-USB-UV User Manual (Ver. 1.1) Preparation Step 5: Change the Camera Settings This section explains how to change settings by describing the procedure for changing the output format as an example. Configure the Output Format Configure the size, position, and pixel format of the images to be acquired. The factory settings are as follows.
GO-5000M-USB-UV User Manual (Ver. 1.1) Preparation Step 6: Adjust the Image Quality Display the camera image and adjust the image quality. Display the Image Display the image captured by the camera. When you click the Play button, the camera image appears in the right area.
GO-5000M-USB-UV User Manual (Ver. 1.1) Preparation Step 7: Save the Settings The configured setting values will be deleted when the camera is turned off. By saving current setting values to user memory, you can load and recall them whenever necessary. You can save up to three sets of user settings in the camera.
GO-5000M-USB-UV User Manual (Ver. 1.1) Preparation To Save User Settings 1. Stop image acquisition. 2. Expand UserSetControl and select the save destination (UserSet1 to UserSet3) in UserSetSelector. Note: The factory default setting values are stored in Default and cannot be overwritten.
GO-5000M-USB-UV User Manual (Ver. 1.1) Preparation To Load User Settings 1. Stop image acquisition. User settings can only be loaded when image capture on the camera is stopped. 2. Select the settings to load (UserSet1 to UserSet3) in UserSetSelector. 3. Select UserSetLoad and click the UserSetLoad button.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Main Functions This chapter describes the camera's main functions. Digital IN/OUT Interface On this camera, the digital IN/OUT capability in the software control tool can assign the necessary signals needed for the system.
Page 28
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Line Source Item Description User Out 0 Connect User Out 0 signal to line item selected in Line Selector User Out 1 Connect User Out 1 signal to line item selected in Line Selector...
Page 29
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Basic Block Diagram - 29 -...
Page 30
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions GPIO IN/OUT Matrix Pulse Generator Trigger Selector Line Selector Selector Acquisition Acquisition Frame Transfer GPIO GPIO NAND 1 NAND 1 NAND 2 NAND 2 Pulse Generator Source Signal Start Stop Start Start In 1...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Optical Interface This camera is equipped with opto-isolated inputs and outputs, providing galvanic separation between the camera’s inputs/outputs and peripheral equipment. In addition to galvanic separation, the opto-isolated inputs and outputs can cope with a wide range of voltages;...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Recommended External Output Circuit Diagram for Customer: Simple Circuit Characteristics of Optical Interface The relationship of the input signal to the output signal through the optical interface is as follows. Input Line Voltage Range: +3.3v ~ +24V...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions OUTPUT LINE RESPONSE TIME Opt In Filter Selector function As for the surge protection of the optical input, the filter can be selected from 5 steps which are 10 μs (Typical), 100 μs, 500 μs, 1 ms and 10 ms. If the filter is set, a pulse with a shorter width than the filter setting value cannot be accepted.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Pulse Generator Tips for using the Pulse Generator This camera has a frequency divider using the pixel clock as the basic clock and one pulse generator. In the Pulse Generator, various Clear settings are connected to GPIO. The following shows the Pulse Generator default settings.
Page 35
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Pulse Generator Selector This is where you select a pulse generator. On this camera, it is fixed to Pulse Generator 0. Pulse Generator setting / Pulse Generator pulse construction Trigger Description Selector item...
Page 36
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Pulse Generator Clear Activation Set the clear conditions of clear count pulse for the pulse generator. Pulse Generator Clear Sync Mode Set the count clear method for the pulse generator. In case of Async Mode, if the clear signal is input during the length setting value, the counter will stop counting according to the clear signal input.
Page 37
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Pulse Generator Clear Source The following clear source can be selected as the pulse generator clear signal. Pulse Generator Description Clear Source Item Connect Low level signal to Clear Source for the pulse generator. Default setting High Connect High level signal to Clear Source for the pulse generator.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Camera Output Format Camera output format: 1X – 1Y Sensor readout system: 1-tap readout Note: The camera output description is based on GenICam SFNC Ver.1.5.1. - 39 -...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Output Timing (Horizontal) The horizontal timing of this camera is described below. Although the camera has a horizontal binning function, its horizontal frequency does not change if it is ON. So, the frame rate is not increased.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions ROI (Region of Interest) Settings On this camera, a subset of the image can be output by setting Width, Height, Offset- X, and Offset-Y. If the height is decreased, the number of lines read out is decreased and as the result, the frame rate is increased.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Acquisition Control Acquisition control contains the following commands. Command Parameter Description Single Frame One frame can be output by AcquisitionStart command The number of frames which is specified in Acquisition Frame Count, Multi Frame...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Acquisition Mode On this camera, the following three acquisition modes are available. Single Frame In single frame mode, executing the AcquisitionStart command causes one frame to be captured. After one frame is captured, this operation is automatically stopped.
Page 49
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Multi-Frame In this mode, the AcquisitionStart command captures the number of frames which are specified by AcquisitionFrameCount. ◆ Normal multi-frame operation 1. AcquisitionStart command is input 2. AcquisitionTriggerWait becomes effective 3. AcquisitionActive becomes “TRUE” (accepts capture) 4.
Page 50
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Continuous In this mode, when the AcquisitionStart command is set, the image is continuously output at the current frame rate. This is the default setting for this camera. ◆ Normal continuous operation 1. AcquisitionStart command is input 2.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Acquisition Start This is the command to start the capture. Acquisition Stop This is the command to stop the capture. Acquisition Frame Rate With Trigger OFF, the default frame rate of the camera is based on the specified ROI. The smaller the ROI, the faster the default frame rate.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Calculation of the Maximum Frame Rate Maximum frame rate(fps) = 1 / (Roundup ([Line Period] x [Height ] + [V Blank Value]) / 1000000) Where [Line Period] = [Trow] / 24 [Trow] = Rounddown...
Page 53
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Notes: *1: Round down after the decimal point *2: Refer to the Height value on the above table. In the binning Vertical, the maximum value is changed. *3: Round down after the decimal point *4: The maximum frame rate of full pixels image size (2560 x 2048) If the width is changed, the frame rate is not changed.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Exposure Mode The exposure mode can be selected from the following three ways. Exposure Mode Exposure Operation Setting No exposure control (free-running operation) Exposure operation at the value set in Exposure Time. Setting value is μs unit.
Page 55
Note: Noise may make image unusable after 1 second) ExposureAuto This is a function to control the exposure automatically. It is effective only for Timed. JAI ALC Reference controls the brightness. There are two modes, OFF and Continuous. OFF: No exposure control Continuous: Exposure continues to be adjusted automatically In this mode, the following settings are available.
Page 56
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions ALC Channel Area - 56 -...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Trigger Control The following 5 types of Trigger Control are available by the combination of Trigger Selector, Trigger Mode, Exposure Mode and Trigger Option. Camera Settings JAI Custom Trigger Description Trigger Trigger Exposure...
Page 58
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Trigger Source The following signals can be used as the trigger source signal. Trigger Source Description Item Connect LOW level signal to the selected trigger operation (Default setting) High Connect HIGH level signal to the selected trigger operation Connect Soft Trigger signal to the selected trigger operation.
Page 59
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Trigger Activation This command can select how to activate the trigger. Rising edge: At the rising edge of the pulse, the trigger is activated. Falling edge: At the falling edge of the pulse, the trigger is activated.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Normal Continuous Operation This is used for applications which do not require triggering. Primary settings to use this mode Trigger Mode: Off Minimum interval of the trigger Read Out Mode Minimum Trigger Interval Full 16.155 ms...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Timed Mode This mode allows a single image frame to be captured with a preset exposure time by using the external trigger. Additional settings determine if the trigger pulse can be accepted during the exposure period.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Trigger Width Mode In this mode, the exposure time is equal to the trigger pulse width. Accordingly, longer exposure times are supported. Additional settings determine if the trigger pulse can be accepted during the exposure period.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions RCT (Reset Continuous Trigger) Mode RCT mode can use ALC control to ensure that the proper exposure is set when the trigger pulse is input. the following drawing, the steps to achieve this combination are explained.
Page 64
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Primary settings to use this mode Exposure Mode: Timed Trigger Selector: Frame Start Trigger Mode: ON Trigger Option: RCT If ALC control is used together with RCT mode, then Exposure auto: Continuous Gain Auto: Continuous...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Video Send Mode This camera has a Video Send Mode, and it includes the following operations. Mode Index Selection method Selected Normal Normal operation Multi ROI Up to 5 ROI images can be set up. Each image is output independently.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Sequence Mode This mode allows the user to define a preset sequence of up to 10 images, each with its own ROI, exposure time and gain values. This mode has two operation modes.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Trigger Sequence Mode Timing In this mode, as each trigger input is received, the image data associated with the next index within the preset sequence is output. In the trigger sequence mode, it is not possible to input the trigger while the current index is executing.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Sequence Index Table (Default) The following table shows the default settings. Sequence ROI Gain Offset Binning Selector Exposure Black Frame Next Time Level Enable Count Index Sequence ROI Width Height X Y Gain (ALL)
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Descriptions of Index Table Parameters Sequence Mode Command Command Parameter Description Sequence ROI Index Index 1 ~ 10 Select an index to be set <Set to each Index> Sequence ROI Frame 1 ~ 255...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Multi ROI Mode On this camera, the width and height of 5 separate ROIs within the full image area can be set as required. Each image can be overlapped. The location of each ROI can also be set as required. The Multi ROI data is output as an independent frame.
Page 71
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Multi ROI Setting Example - 71 -...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Delayed Readout Function The images captured by Frame Start trigger can be stored inside the camera and read out by Acquisition Transfer Start trigger. Up to 7 frames can be stored. Command Setting...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Operation and Function Matrix Video Send Mode Exposure Trigger Trigger Exposure Auto ROI Auto Multi Operation mode Option Binning Binning Time Gain Sequence Exposure ✓ ✓ ✓ 2 / 4 2 / 4 ✓...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Black Level Control This function adjusts the setup level. Reference Level 33.5LSB (Average of 100 x 100 pixels) Video Level Variable Range 0 ~ approx.100 LSB Adjusting Level -256 ~ 255 (Default: 0) Resolution 1STEP=0.25LSB...
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Gain Control On this camera, the gain control uses Analog Base Gain and Digital Gain. Analog Base Gain can be set at 0dB, +6dB or +12dB. The digital gain is used for the master gain setting.
Page 76
Gain Raw The range for adjustment: Gain Raw Digital All: 100 ~ 1600 (0dB ~ 24dB) Gain Auto This provides automatic control of the gain level. This is controlled by the command JAI ALC Reference. OFF: Adjust manually. Once: Operate only one time when this command is set Continuous: Operate the auto gain continuously The following detailed settings are also available.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions LUT (Lookup Table) This function can be used to convert the input to the desired output characteristics. The Lookup Table (LUT) has 32 points for setup on this camera. The output level can be created by multiplying the gain data by the input level.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Gamma This command is used to set gamma 0.45, gamma 0.6 and gamma 1.0 (OFF) in 3 steps. The gamma value is an approximate value. Linear and Dark Compression This camera has a dark compression circuit to improve the signal-to-noise ratio in the dark portion of the image.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Shading Correction Flat Shading Correction: The method to compensate the shading is to measure the highest luminance level in the image and use that data as the reference. Luminance levels of other areas are then adjusted so that the level of the entire area is equal.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions Blemish Compensation This camera has a blemish compensation circuit. This function compensates blemishes on the CMOS sensor (typically pixels with extremely high response or extremely low response). Pixels that fulfill the blemish criteria can be compensated by averaging the data from the pixel in the left adjacent column.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions ALC (Automatic Level Control) On this camera, auto gain and auto exposure can be combined to provide a wide ranging automatic exposure control from dark to bright or vice versa. The functions are applied in the sequence shown below and if one function is disabled, the remaining function will work independently.
GO-5000M-USB-UV User Manual (Ver. 1.1) Main Functions HDR (High Dynamic Range) HDR sensing mode can be set when HDR Mode is set to ON while Exposure Mode is Timed. The parameters to configure dynamic range are HDR_SLOPE Level 1, Level 2, Level 3 and Level 4.
Page 86
GO-5000M-USB-UV User Manual (Ver. 1.1) Miscellaneous Specifications Description Full pixels: 2560 (h) x 2048 (v) Width 16 ~ 2560, 16 pixels/step OFFSET X 0 ~ 2544, 16 pixels/step Height 1 ~ 2048 lines,1 line/step OFFSET Y 0 ~ 2047 lines, 1 line/step...
Page 87
GO-5000M-USB-UV User Manual (Ver. 1.1) Miscellaneous Specifications Description Gamma γ=0.45, 0.6, 1.0 (3 steps are available) Dark compression Choice of Linear or Dark compression ON Shading Compensation Flat Field, Block Com. (20 x 16 blocks), Block Size: 128 x 128 pixels OFF: γ=1.0, ON=32 points can be set...
GO-5000M-USB-UV User Manual (Ver. 1.1) Miscellaneous Appendix Precautions Personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive components.
Page 89
GO-5000M-USB-UV User Manual (Ver. 1.1) Miscellaneous Caution When Mounting a Lens on the Camera When mounting a lens on the camera dust particles in the air may settle on the surface of the lens or the image sensor of the camera. It is therefore important to keep the protective caps on the lens and on the camera until the lens is mounted.
GO-5000M-USB-UV User Manual (Ver. 1.1) User's Record User's Record Model name: GO-5000M-USB-UV Revision: …………… Serial No: …………… Firmware version: …………… For camera revision history, please contact your local JAI distributor. - 90 -...
GO-5000M-USB-UV User Manual (Ver. 1.1) Revision History Revision History Revision Date Changes 2022/11/17 Redesigned the User Manual. Feb 2021 First Release Trademarks Other systems and product names described in this document are trademarks or registered trademarks of their respective owners. The ™ and ®...