Identification; Technical Data; Installation And Assembly; Notes - Reflex Exdirt Magneto Original Operating Manual

Exdirt Magneto DN 200 - 400
1 Service flange with Exferro magnet insert
2 Drain valve (included in the accessory kit)
3 Magnesium sacrificial anode (optional for blanking plug)
4 Exferro magnet insert in immersion sleeve
5 Vent plug
6 Blanking plug
3

Technical data

Note!
The following values apply for all standard separators:
• Max. temperature: 0-110 °C
• Max. pressure: 10 bar
• Special versions according to individual specification and nameplate.
Contact the manufacturer to determine the weight of the separator.
H
L (mm)
(mm)
DN 50 294 241
DN 65 344 261
DN 80 354 261
DN 100 358 261
DN 125 414 340.5
DN 150 414 340.5
DN 200 480 390.5
DN 250 546 484.7
DN 300 600 564.7
DN 400 550 614.7
4

Installation and assembly

CAUTION
Risk of burns
Escaping hot medium can cause burns.
• Maintain a sufficient distance from the escaping medium.
• Wear suitable personal protective equipment (safety gloves and
goggles).
4.1

Notes

The following items must be considered for assembly and installation of the
equipment:
• Do not install the device above sensitive components or close to electrical
plant.
• Perform installation in dry and frost-proof locations.
• The flow direction is not specified.
• The component can be installed horizontally or vertically.
D Plug
(mm) Brass
165 10.6 1"
185 12.9 1"
200 14.7 1"
220 16.4 1"
250 32.7 1 1/4"
285 36.5 1 1/4"
340 50.9 1 1/4"
405 81.2 1 1/4"
460 111.7 1 1/4"
580 156.5 1 1/4"
Exdirt magneto — 25.10.2022-Rev. B
2.1

Identification

Information on the type plate
XXX
Type
Connections
Max. allowable pressure
Max. allowable temperature
Year of manufacturing
Serial no.
Art.-No-
Ø
Magnet Sacrificial
Sacrificial
insert anode
anode
1 1 3/4"
1 1 3/4"
1 1 3/4"
1 1 3/4"
1 1 3/4"
1 1 3/4"
1 1 3/4"
2 1 3/4"
2 1 3/4"
3 1 3/4"
• During installation ensure there are no residual stresses.
– Any stresses that may occur in some cases must be countered by
appropriate constructive actions. Stresses may be caused by
temperature effects, for example.
• Ensure the device is readily accessible in its installation location.
• Ensure sufficient bearing capability of the installation site.
– This applies to filling the separator with water in particular.
– If necessary additional structural measures may be required to
ensure adequate load bearing capacity.
• The device is not a load-bearing structural element.
– By default, the calculation of the vessels does not take lateral
acceleration forces into account. Avoid alternating stresses such as
pressure shocks, abrupt pressure changes, or strong vibrations.
• Use only approved transport and lifting equipment.
• The angle of the lifting tackles must be maximum 60°.
• After attachment of insulation, attach the additional sticker on the outside
so that it is readily visible.
• Flush the system thoroughly after installation.
Meaning
Device name
Device type
Connection
Maximum permissible pressure
Maximum permissible temperature
Year of manufacturing
Serial number
Article number
Service flange
/ coupling
Female 2"
Female 2"
Female 2"
Female 2"
DN65
DN65
DN65
DN65
DN65
DN65
Technical data
English — 9