Collaboration Capability [Linkage] - Panasonic AW-UE100WP Operating Instructions Manual

Web screen configurations (continued)

Collaboration capability [Linkage]

Tracking data output settings screen [Tracking
„ „
Data Output]
Select the output mode of the tracking data and the communication
destination in the IP mode.
Up to four addresses can be specified when the IP mode is enabled.
z Setting status
„
Displays the output mode of tracking data and the destinations in IP
mode.
z Connection type
„
Serial [On, Off]
Sets the function [On] or [Off] to output the tracking data, such as
Pan/Tilt/Zoom or other information from Serial Output (RS-422),
synchronized with the Genlock signal. (→ page 64)
When [Serial] is set to [On], a warning message is displayed. Click
the [OK] button to enable the settings.
Factory settings: Off
<NOTE>
• The serial connection of the remote controller (AW-RP150 or
AW-RP60 etc.) cannot be made if [Serial] is already [On].
• In the following cases, the tracking data output may be delayed or
the value may not be updated.
- While viewing the OSD menu
- While recalling the preset value during an ongoing preset recall
- When executing AWB/ABB
- When a red or a green tally signal input has been changed
between Off and On
- When deleting a preset memory
- When an output image is flipped (turned upside down or left-right
reversed)
- After switching [Scene]
- After switching [Iris Mode]
- After switching [Super Gain]
- After switching [White Balance Mode]
- After switching each item of [Color Temperature Setting]
- After switching [Gamma Mode]
- After switching [Matrix Type]
- After switching [Focus Mode]
- After switching [Zoom Mode]
- After switching [Max Digital Zoom]
- After switching [Digital Extender]
- After switching [Fan]
- After switching [OSD Mix/Crop Marker]
- After switching [Tally]
- After moving the crop frame of [Crop Mode]
- After switching [Install Position]
- After switching [Preset Speed Unit]
- When executing [Reset to the default (Except the network
settings)] of [Maintenance]
IP(UDP) [On, Off]
Sets the UDP output function [On] or [Off] to output tracking data,
such as Pan/Tilt/Zoom or other information from the IP output,
synchronized with the Genlock signal. (→ page 65)
When [IP(UDP)] is set to [On], a warning message is displayed. Click
the [OK] button to enable the settings.
Factory settings: Off
<NOTE>
• When [IP(UDP)] is [On], video transmission via IP may be delayed
or the video may suffer frame loss.
We recommend setting [IP(UDP)] to [Off] to avoid the delay or frame
loss due to the video transmission via IP.
• In the following cases, the tracking data output may be delayed or
the value may not be updated.
- When performing video transmission via IP (M-JPEG/H.264/H.265/
RTMP/RTMPS/NDI/NDI|HX/SRT)
- When opening the web screen (live screen [Live] or the web
setting screen [Setup])
- While viewing the OSD menu
- While recalling the preset value during an ongoing preset recall
- When executing AWB/ABB
- When a red or a green tally signal input has been changed
between Off and On
- When deleting a preset memory
- When an output image is flipped (turned upside down or left-right
reversed)
- After switching [Scene]
- After switching [Iris Mode]
- After switching [Super Gain]
- After switching [White Balance Mode]
- After switching each item of [Color Temperature Setting]
- After switching [Gamma Mode]
- After switching [Matrix Type]
- After switching [Focus Mode]
- After switching [Zoom Mode]
- After switching [Max Digital Zoom]
- After switching [Digital Extender]
- After switching [Fan]
- After switching [OSD Mix/Crop Marker]
- After switching [Tally]
- After moving the crop frame of [Crop Mode]
- After switching [Install Position]
- After switching [Preset Speed Unit]
- When executing [Reset to the default (Except the network
settings)] of [Maintenance]
136