Table of Contents
Advertisement
Quick Links
150 TON AIR POWERED TIRE PRESS
Model 33-578
INSTRUCTIONAL MANUAL
WARNING!
Read and understand all instructions and responsibilities before operating. Failure to follow safety
instructions and labels could result in serious injury.
Dake Corporation
Phone: 800.937.3253
www.dakecorp.com
1809 Industrial Park Dr
Grand Haven, MI 49417
Advertisement
Table of Contents
Related Manuals for Dake 33-578
Summary of Contents for Dake 33-578
- Page 1 150 TON AIR POWERED TIRE PRESS Model 33-578 INSTRUCTIONAL MANUAL WARNING! Read and understand all instructions and responsibilities before operating. Failure to follow safety instructions and labels could result in serious injury. Dake Corporation Phone: 800.937.3253 www.dakecorp.com 1809 Industrial Park Dr...
-
Page 2: Table Of Contents
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com TABLE OF CONTENTS SAFEGUARDING THE POINT OF OPERATION ............2 SPECIFICATIONS ......................3 SAFETY ........................4 SET UP ......................... 5 OPERATION ......................... 5 MAINTENANCE ......................6 LUBRICATION ..................... 6 REPLACING HYDRAULIC OIL ................ -
Page 3: Safeguarding The Point Of Operation
ANSI B11.2 - Hydraulic Power Presses - Safety Requirements for Construction, Care, and Use It is important that Dake press users have a clear understanding of their responsibility involving the care and use of their Dake hydraulic press, including point-of-operation safe guards. Dake strongly recommends that Dake press users obtain a copy of the current American National Standard Institute (ANSI) B11.2 standard, for... -
Page 4: Specifications
In the space provided record the serial number and model number of the machine. This information is only found on the black and gold Dake tag shown below. If contacting Dake this information must be provided to assist in identifying the specific machine. -
Page 5: Safety
• Do not make repairs or adjustments to any hydraulic system unless you are competent or working under competent supervision. • Only use Dake original parts. • This machine is intended to be operated by one person. This person should be conscious of the press ram movement not only for themselves but also for persons in the immediate area of the machine. -
Page 6: Set Up
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com SET UP 1. Anchor press to floor using 11/16” holes on the base angles of the press. 2. Connect airline from source of supply to Pipe Tee located above operative valve. -
Page 7: Maintenance
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com MAINTENANCE LUBRICATION • Keep all working parts of the press well-oiled for easier operation. • Keep a light film of oil over the entire surface of the ram to prevent rust. - Page 8 Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com C. Press does not develop rated tonnage. 1. Dirt under Release Valve Ball: See section above. 2. Worn Leather Cup or Piston Seal: See section above. 3. Air pressure too low: If the air supply is less that 90PSI the pump may develop less than the rated tonnage.
-
Page 9: Hydraulic Diagram
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com HYDRAULIC DIAGRAM Item Part No. Description 1904P Reservoir 700232 Check Valve 63453 Air Pumps 1911 Quick Exhaust Valve 710557 Release Valve 71268 Gauge 700147 Check Valve 707070A Workhead 1841... -
Page 10: Exploded Views & Parts Lists
Label, Warning - Keep Fingers Out of Pin Holes 36863 Label, Warning , End of Stroke 43647 Lock Washer (1/2) 43648 Lock Washer (5/8) 81003 Name Plate, Dake 44194 Nipple, Pipe XS, (3/4 x 2-1/2) 43919 Nut, Hex (3/4-10) 43917 Nut, Hex (5/8-11) 77271 Pin, Spring (3/8"... - Page 11 Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com 1822P Reservoir Cover 43978 Ring, Retaining (3/4" Shaft Size) 302816 Safety Pin for Table Pins 43347 Screw (1/2-13 x 1) 43365 Screw (5/8-11 x 1-3/4) 43348 Screw , Hex Cap (1/2-13 x 1-1/4) 70277 Screw, Drive (#4 x 5/16"...
- Page 12 Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com 707070A Workhead Assembly – New Style Item Part No. Description 1796P Piston 52478P Retainer 31871 Guide, Piston 43647 Washer, Lock (1/2”) 43419 Screw, Soc Cap (1/4-20 x 2) 43359...
- Page 13 Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com 707070 Workhead Assembly – Old Style Item Part No. Description 1796P Piston 52478P Retainer 31871 Guide, Piston 43647 Washer, Lock (1/2”) 43916 Screw, Soc Cap (1/4-20 x 2) 43359...
- Page 14 Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com 701350 Relief Valve Assembly Item Part No. Description 1093P Relief Valve Body 1222 Valve, Ball (5/16") 1094P Retainer, Ball 1221 Spring, Valve Compressor 1095P Retainer, Spring 1111 O-Ring, Unif 215 Buna...
- Page 15 Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com 710557 Release Valve Assembly Item Part No. Description 1752P Release Valve Block 1936 Valve, Ball 1937 Washer, Valve Rod Packing 1931P Packing Nut 47946P Release Valve Rod 2230A Handle, Release Valve Spindle Washer (1-1/2"...
- Page 16 Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com TABLE HOIST ASSEMBLY Item Part No. Description Cable Drum 43983 Ring, Retaining (1-1/4” Shaft Size) Worm, Worm Shaft Key (1/4 x 1/4 x 3-7/16) 43982 Ring, Retaining (1” Shaft Size)
-
Page 17: Ordering Information
Please contact factory for current prices. Parts are available for direct purchase from Dake or through a distributor. When placing a parts order, you will need to provide the part number, name of part, and model number. All parts shipped F.O.B. Factory in Grand Haven, MI.