Mouvex SLS12 i Installation Operation & Maintenance
  1. Manuals
  2. Brands
  3. Mouvex Manuals
  4. Water Pump
  5. SLS12 i
  6. Installation operation & maintenance

Mouvex SLS12 i Installation Operation & Maintenance

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SLS12 i - SLS18 i
SL Series pumps are covered 24 months by warranty within the limits mentioned in our General Sales Conditions.
In case of a use other than that mentioned in the Instructions manual, and without preliminary agreement of MOUVEX,
warranty will be canceled.
Z.I. La Plaine des Isles - F 89000 AUXERRE - FRANCE
Tel. : +33 (0)3.86.49.86.30 - Fax : +33 (0)3.86.49.87.17
contact@mouvex.com - www.mouvex.com
PUMPS
WARRANTY :
INSTRUCTIONS 1004-G00 e
Section
1004
Effective
July 2018
Replaces
October 2016
Original instructions
INSTALLATION
OPERATION
MAINTENANCE
Your distributor :

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SLS12 i and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Mouvex SLS12 i

Summary of Contents for Mouvex SLS12 i

  • Page 1 SL Series pumps are covered 24 months by warranty within the limits mentioned in our General Sales Conditions. In case of a use other than that mentioned in the Instructions manual, and without preliminary agreement of MOUVEX, warranty will be canceled.

  • Page 2: Table Of Contents

    14. TROUBLESHOOTING ......26 must be followed. 15. CERTIFICATE OF CONFORMITY ....28 NT 1004-G00 07 18 SLS12 i - SLS18 i e 2/28...

  • Page 3: Overall Dimensions

    1. OVERALL DIMENSIONS NT 1004-G00 07 18 SLS12 i - SLS18 i e 3/28...
  • Page 4 [30.118] [9.134] [17.244] [18.13] [6.161] [7.047] [2.835 x 0.118] [254] DIN 11851 72 x 3 480,5 156,5 SLS18i [2.559] [30.906] [9.921] [18.031] [18.917] [6.161] [7.047] [2.835 x 0.118] [265] NT 1004-G00 07 18 SLS12 i - SLS18 i e 4/28...
  • Page 5 1. OVERALL DIMENSIONS (continued) NT 1004-G00 07 18 SLS12 i - SLS18 i e 5/28...
  • Page 6 1. OVERALL DIMENSIONS (continued) NT 1004-G00 07 18 SLS12 i - SLS18 i e 6/28...
  • Page 7 1. OVERALL DIMENSIONS (continued) NT 1004-G00 07 18 SLS12 i - SLS18 i e 7/28...

  • Page 8: Installation

    R = 3 x D minimum Diameter must be at least equal to pump port diameter and even more if required by pumping conditions. L = 10 x D minimum NT 1004-G00 07 18 SLS12 i - SLS18 i e 8/28...

  • Page 9: Orientation Of The Pump Ports

    Turn the pump the wrong way is not dangerous for the pump. • If pumped liquid presents a risk of in pipe solidification and potential dilatation, low points on the pipe should be avoided or equipped with drain valve. NT 1004-G00 07 18 SLS12 i - SLS18 i e 9/28...

  • Page 10: Protection Of The Pump Installation

    WARNING FAILURE TO INSTALL ADEQUATELY SIZED PRESSURE RELIEF VALVE(S) CAN CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. Hazardous pressure can cause personal injury or property damage. NT 1004-G00 07 18 SLS12 i - SLS18 i e 10/28...

  • Page 11: Unit Assembly

    (if the need arises, Angular fault use the values given on the overall dimension drawing). For staff and equipment protection, the frame includes a ground connection point that should be used. NT 1004-G00 07 18 SLS12 i - SLS18 i e 11/28...
  • Page 12 Using electric motors is very common now; however, we strongly advise careful reading of the accompanying ins- truction manual. NT 1004-G00 07 18 SLS12 i - SLS18 i e 12/28...

  • Page 13: Utilisation

    For any pure water pumping during process or cleaning operations, consult Mouvex imperatively. NT 1004-G00 07 18 SLS12 i - SLS18 i e 13/28...

  • Page 14: Clean In Place (Cip) & Sterilisation In Place (Sip)

    SL Series pump This flow corresponds to difficult cleaning (sticky and vis- and the bypass circuit. cous products). It can be reduced for easier types of cleaning. NT 1004-G00 07 18 SLS12 i - SLS18 i e 14/28...

  • Page 15: Pumps Arranged In Parallel

    Max pressure 6 barg (87 psig) SLS pump SLS pump The pump must not run during this operation. The SL Series pump is stopped when cleaning the ins- tallation. NT 1004-G00 07 18 SLS12 i - SLS18 i e 15/28...

  • Page 16: Successive Cycles

    • M8 : 18 Nm • 13-32 Open-end spanner • M16 : 100 Nm • Hub puller • M24 : 200 Nm • 70 Open-end spanner or Monkey wrench NT 1004-G00 07 18 SLS12 i - SLS18 i e 16/28...

  • Page 17: Opening Of The Pump

    No start-up, even accidental, must be allowed. • Disconnect the pump from the discharge pipe. • Unscrew the 6 nuts 106 and remove the 6 tierods 105- 107. NT 1004-G00 07 18 SLS12 i - SLS18 i e 17/28...

  • Page 18: Checking Of Parts

    : • Triangular shape on top of piston wall (A), • Small steps at piston wall base (B). • Remove the cylinder 201 and the seals 113 and 306. NT 1004-G00 07 18 SLS12 i - SLS18 i e 18/28...
  • Page 19 Piston must then look as follows : disc wall edges. Even if it shows wearing signs, do not retouch any surface of the cylinder by any mean as it can degrade pump performance and reliability. NT 1004-G00 07 18 SLS12 i - SLS18 i e 19/28...

  • Page 20: Assembly Of Cylinder/Piston

    BE CAREFUL WITH THE WEIGHT OF THE PARTS WHEN THEY ARE BEING REMOVED. The weight ot the parts can be dangerous and may provoke bodily injuries or material damages. Loctite ® is a registered trademark. NT 1004-G00 07 18 SLS12 i - SLS18 i e 20/28...

  • Page 21: Protection Of The Bellows

    117. The nuts 115 must be re-mounted with thread locking adhesive (Loctite ® 243* or equivalent) : 4 x M16 : Assembly torque 100 Nm. Loctite ® is a registered trademark. NT 1004-G00 07 18 SLS12 i - SLS18 i e 21/28...

  • Page 22: Changing The Lip Seal

    Compulsory reference because compatible with the standard MOUVEX bearing oil. • Replace the circlip 725. * Standard oils provided by MOUVEX (Safety data sheet is supplied • After replacing the drain plug, fill the bearing (see § DRAINING on inquiery) : OF BEARING with 2 litres of oil*.

  • Page 23: Changing The Orientation Of The Ports

    • Replace the 6 rods 105-107 and tighten the nuts 106. • Make sure that the seal 205 is secured in its housing. Secure it with a grease that is compatible with the transferred product if necessary. NT 1004-G00 07 18 SLS12 i - SLS18 i e 23/28...

  • Page 24: Draining Of Bearing

    • Check oil level that the level is between 1 and 5 mm above the shaft. • Screw back the breather 715. * Standard oils provided by MOUVEX (Safety data sheet is supplied on inquiery) : CS05 Food synthetic oil CS23 Silicone free oil for transmission * Other oil provided by customer.

  • Page 25: Storage

    This protection should also prevent condensation. The pump should be turned a few revolutions manually every two months. NT 1004-G00 07 18 SLS12 i - SLS18 i e 25/28...

  • Page 26: Troubleshooting

    (the piston bushings are worn, worn piston and cylinder, broken piston wear compensation springs, worn partition, broken shaft). NT 1004-G00 07 18 SLS12 i - SLS18 i e 26/28...
  • Page 27 (faulty alignment, deformation of the chassis, stress exerted by the piping on the flanges, seizing, etc.). Excessive consumption of electricity can also be due to a poor motor connection (e.g. a 3 phase motor operating on 2 phases). NT 1004-G00 07 18 SLS12 i - SLS18 i e 27/28...

  • Page 28: Certificate Of Conformity

    15. CERTIFICATE OF CONFORMITY NT 1004-G00 07 18 SLS12 i - SLS18 i e 28/28...

This manual is also suitable for:

Sls18 i

Table of Contents