Table of Contents
Advertisement
Quick Links
S Series pumps are covered 24 months by warranty within the limits mentioned in our General Sales Conditions.
In case of a use other than that mentioned in the Instructions manual, and without preliminary agreement of MOUVEX,
warranty will be canceled.
Z.I. La Plaine des Isles - F 89000 AUXERRE - FRANCE
Tel. : +33 (0)3.86.49.86.30 - Fax : +33 (0)3.86.49.87.17
contact.mouvex@psgdover.com - www.mouvex.com
S4C PUMP
WARRANTY :
INSTRUCTIONS 1002-B00 e
Section
1002
Effective
July 2019
Replaces
February 2018
Original instructions
INSTALLATION
OPERATION
MAINTENANCE
Your distributor :
Advertisement
Table of Contents
Related Manuals for Mouvex S4C
Summary of Contents for Mouvex S4C
- Page 1 S Series pumps are covered 24 months by warranty within the limits mentioned in our General Sales Conditions. In case of a use other than that mentioned in the Instructions manual, and without preliminary agreement of MOUVEX, warranty will be canceled.
-
Page 2: Table Of Contents
7.3 Restarting ........14 must be followed. 8. CERTIFICATE OF CONFORMITY ....15 NT 1002-B00 07 19 S4C Pump e 2/15... -
Page 3: Overall Dimensions
1 - 2 - 3 - 4 Discharge 1 - 2 - 3 - 4 This position of the mounting bracket does not permit orientation of the discharge in position 4. Dimensions in millimetres NT 1002-B00 07 19 S4C Pump e 3/15... -
Page 4: Installation
Suction pipe configuration Check tightness to avoid accidental air intake. 2.1.1 Pump To obtain the service expected from a MOUVEX pump, regarding both performance and longevity, it is vital that the type of pump, its speed and the materials used for its construction are determined as a function of the pump output, its installation and operating conditions. -
Page 5: Orientation Of The Pump Ports
2.3 Direction of rotation be avoided or equipped with drain valve. The S4C pump only has one rotation direction (the pump not being reversible), clockwise (observer facing the back of the pump). -
Page 6: Protection Of The Installation
The following instructions apply to pumps delivered with use the values given on the overall dimension drawing). a bare shaft or for MOUVEX motor-driven pump units (if the latter have no specific instruction notice). For staff and equipment protection, the frame includes a ground connection point that should be used. - Page 7 Using electric motors is very common now; however, we strongly advise careful reading of the accompanying ins- truction manual. NT 1002-B00 07 19 S4C Pump e 7/15...
-
Page 8: Use
A compressor effect close to 3 bar is obtained for a period of 3 minutes. After that, the value falls to 0.5 bar as the lubrication ensured by the pumped product rapidly disap- pears from between the piston and the cylinder. NT 1002-B00 07 19 S4C Pump e 8/15... -
Page 9: Clean In Place (Cip) & Sterilisation In Place (Sip)
Although a particular care was taken to clean- liness when assembling the pump, we recom- The CIP pump must be installed in series with the S4C mend to carry out a cleaning of the pump before pump (see fig. 1) or the couple piston/cylinder risks any use. -
Page 10: Sterilisation In Place (Sip)
Figure 4 CIP Pump S4C Pump Indeed, in this case, the pressure at entry to the S4C pump is lower than the exit pressure and the piston remains stuck against the cylinder. The S4C pump is not flushed through. Its good cleaning is therefore no longer ensured and the cylin- der/piston couple will be prematurely worn. -
Page 11: Assembly / Dismantling
- Wrench no. 16 No start-up, even accidental, must be possible. - Plastic mallet - Hexagonal socket wrench no. 6 Assembly torques : - M8 : 23,7 Nm - M10 : 30 Nm NT 1002-B00 07 19 S4C Pump e 11/15... -
Page 12: Opening The Pump
101). then the hand nut 311. Re-mount the base 401 and the seal 205 taking care to give the discharge port the desired angular position. ® Loctite is a registered trademark. NT 1002-B00 07 19 S4C Pump e 12/15... -
Page 13: Maintenance
(1,142) As changes in the pump's efficiency depend on the conditions of use (pressure, rotation speed, liquid pum- ped, etc.), MOUVEX recommends that users define the monitoring ranges and the preventive maintenance schedule according to their own experience. d : measured distance 6.2 Checking of seals... -
Page 14: Storage
• Etc. Do not attempt to remove the sleeve or to empty the oil MOUVEX pumps and motor-driven pumps are well lubri- from it. This operation can only be done in the factory. cated when delivered to protect the internal parts during If in doubt, replace the complete transmission. -
Page 15: Certificate Of Conformity
8. CERTIFICATE OF CONFORMITY NT 1002-B00 07 19 S4C Pump e 15/15...
Need help?
Do you have a question about the S4C and is the answer not in the manual?
Questions and answers