1. Manuals
  2. Brands
  3. Mouvex Manuals
  4. Water Pump
  5. C12 A
  6. Installation operation & maintenance

Mouvex C12 A Installation Operation & Maintenance

Hide thumbs
Table of Contents

Advertisement

Quick Links

Z.I. La Plaine des Isles - F 89000 AUXERRE - FRANCE
Tel. : +33 (0)3.86.49.86.30 - Fax : +33 (0)3.86.49.87.17
contact@mouvex.com - www.mouvex.com
C12 A - C18 A
PUMPS
INSTRUCTIONS 1001-F00 e
Section
1001
Effective
October 2010
Replaces
August 2010
Original instructions
INSTALLATION
OPERATION
MAINTENANCE
Your distributor :

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C12 A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Mouvex C12 A

Summary of Contents for Mouvex C12 A

  • Page 1 Section 1001 Effective October 2010 Replaces August 2010 Original instructions C12 A - C18 A PUMPS INSTALLATION OPERATION MAINTENANCE Your distributor : Z.I. La Plaine des Isles - F 89000 AUXERRE - FRANCE Tel. : +33 (0)3.86.49.86.30 - Fax : +33 (0)3.86.49.87.17...

  • Page 2: Table Of Contents

    13.2 Bellow monitoring system .....19 must be followed. 14. CERTIFICATE OF CONFORMITY ....20 NT 1001-F00 10.10 C12 A - C18 A e 2/20...

  • Page 3: Overall Dimensions

    1. OVERALL DIMENSIONS NT 1001-F00 10.10 C12 A - C18 A e 3/20...
  • Page 4 1. OVERALL DIMENSIONS (continued) NT 1001-F00 10.10 C12 A - C18 A e 4/20...
  • Page 5 1. OVERALL DIMENSIONS (continued) NT 1001-F00 10.10 C12 A - C18 A e 5/20...

  • Page 6: Installation

    Verification of the correct rotation direction : Turn the pump the wrong way is not dangerous for the pump. NT 1001-F00 10.10 C12 A - C18 A e 6/20...

  • Page 7: Hoisting Devices

    AND PROPERTY DAMAGE. Hazardous pressure can cause The following instructions apply to pumps delivered with personal injury a bare shaft or for MOUVEX motor-driven pump units (if or property damage. the latter have no specific instruction notice). 2.5.1 INSTALLATION OF UNITS CAUTION...
  • Page 8 The motors should be protected with circuit breakers and suitable fuses. Connect the regulatory electrical grounding. NT 1001-F00 10.10 C12 A - C18 A e 8/20...

  • Page 9: Utilisation

    The C series pump is self priming and is capable of emp- conditions without the drive is less than 81 dB(A). tying the pipes. To do this, it can run dry for a maximum duration of 5 minutes. NT 1001-F00 10.10 C12 A - C18 A e 9/20...

  • Page 10: Pump Stop

    PARTS WHEN THEY ARE BEING REMOVED. SPILLS MUST BE CLEANED UP. The weight ot the parts can Slippery lubricant. be dangerous and may Spills should be provoke bodily injuries or cleaned up. material damages. NT 1001-F00 10.10 C12 A - C18 A e 10/20...

  • Page 11: Assembly / Dismantling

    • With the help of a hub puller, extract the piston 301. • Remove the front cover 401 with its seal 205. • Remove the cylinder 201 and the seals 113, 306 and 307. NT 1001-F00 10.10 C12 A - C18 A e 11/20...

  • Page 12: Checking Of Parts

    Piston Cylinder mm (inch) mm (inch) New dimension (0,354) (1,969) Minimum wear dimension acceptable (0,236) (1,850) New dimension (0,354) (2,756) Minimum wear dimension acceptable (0,236) (2,638) NT 1001-F00 10.10 C12 A - C18 A e 12/20...

  • Page 13: Reassembly Of Cylinder/Piston

    • Screw the 6 screws 106 (6 x M16 assembly torque 100 Nm). ® • Place thread locking adhesive (Loctite 243* or equivalent) on the thread of the transmission hub 596. Loctite ® is a registered trademark. NT 1001-F00 10.10 C12 A - C18 A e 13/20...

  • Page 14: Protection Of The Bellows

    The screws 111 must be re-mounted with thread locking adhesive (Loctite ® 243* or equivalent) : 4 x M16 : Assembly torque 100 Nm. Loctite ® is a registered trademark. NT 1001-F00 10.10 C12 A - C18 A e 14/20...

  • Page 15: Changing The Lip Seals

    95°C (in an oil bath or at HF). • Place a new seal 518. * Standard oil provided by MOUVEX : CS05 Food synthe- tic oil (Safety data sheet is supplied with the new pump and on inquiery).

  • Page 16: Bypass

    804 (do not remove any associated parts). • Remove the spring 804. • Replace spring 804 and carry out reassembly in rever- se order of disassembly. NT 1001-F00 10.10 C12 A - C18 A e 16/20...

  • Page 17: Heating Jacket (Option)

    • Remove the 4 screws 132 from the main body 101 as well as the main body plate 131 and the seal 130. • Reassembly is in reverse order of disassembly. NT 1001-F00 10.10 C12 A - C18 A e 17/20...

  • Page 18: Draining Of Bearing

    Oil level Min : 1 mm Max : 5 mm * Standard oil provided by MOUVEX : CS05 Food synthe- tic oil (Safety data sheet is supplied with the new pump and on inquiery). * Other oil provided by customer.

  • Page 19: Options

    Any puncture in either one of the two metallic bellows leads to a pressure drop. When the pressure decrease under the pressure switch setting, it cuts the electrical circuit. To connect the electrical pressure switch, follow the manufacturer instruction. NT 1001-F00 10.10 C12 A - C18 A e 19/20...

  • Page 20: Certificate Of Conformity

    Quality Manager MOUVEX sas : Z.I La Plaine des Isles – 2, rue des Caillottes - 89000 AUXERRE – France – SAS au capital de 8 496 855 € Tél : (33) 3.86.49.86.30 – Fax : (33) 3.86.46.42.10 – RCS AUXERRE 389 236 548 – APE 291 B – FR 85 389 236 548 – www.mouvex.com...

This manual is also suitable for:

C18 a

Table of Contents