1. Manuals
  2. Brands
  3. ELZAB Manuals
  4. Barcode Reader
  5. DE2106
  6. Setting manual

ELZAB DE2106 Setting Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

DE2106 Setting Manual

Advertisement

Table of Contents
loading

Summary of Contents for ELZAB DE2106

  • Page 1: De2106 Setting Manual

    DE2106 Setting Manual...

  • Page 2: Table Of Contents

    2 / 134 DE2106 SETTING MANUAL ................................. 1 CHAPTER 1 COMPREHENSIVE SETTINGS ............................. 7 ..................................9 ET CODE IDENTIFICATION ............................ 10 NABLE AND DISABLE THE CONFIGURATION CODE ..................................10 ENDING SETTING CODE ................................11 ESTORE FACTORY EFAULT ..................................... 11 ERSION NUMBER ..................................
  • Page 3 3 / 134 USB keyboard interface ................................29 National keyboard layout ................................ 30 USB transmission speed (delay between characters) ......................32 USB polling speed ..................................33 USB-COM ..............................35 VIRTUAL SERIAL INTERFACE USB HID-POS .................................. 36 INTERFACE Protocol format ..................................36 Host send data format ................................
  • Page 4 4 / 134 Code ID prefix order ................................. 66 Custom Code ID ..................................67 ..................................71 DEFINED PREFIX Send user-defined prefix ................................71 User-defined prefix setting ..............................72 ..................................73 DEFINED SUFFIX Send user-defined suffix ................................73 User-defined suffix setting ............................... 74 ..................................
  • Page 5 5 / 134 Transmission system characters .............................. 86 Allow/prohibit reading UPC-E1 ..............................87 Send check character ................................87 Transmission system characters .............................. 87 2/5 additional bits ................................... 88 EAN-8 ......................................90 EAN-8 ..............................90 LLOW PROHIBIT READING Send check character ................................90 2/5 additional bits ...................................
  • Page 6 6 / 134 Start character and stop character setting ........................... 102 5 ..................................103 NTERLEAVED Allow/Prohibit Interleaved 2 of 5 ............................103 Check character setting ................................. 103 5 ....................................104 ATRIX Allow/ Prohibit read Matrix 2 of 5 ............................104 Check character setting .................................

  • Page 7: Chapter 1 Comprehensive Settings

    7 / 134 ID ..................................125 PPENDIX -ASCII ................................126 PPENDIX CODE TABLE Chapter 1 Comprehensive Settings Introduction This manual is mainly used to introduce how to set the corresponding functions of the scanner product;...
  • Page 8 8 / 134 There are two ways to set up the scanner. Setting code The scanner can set the corresponding function by reading the corresponding one or a group of special barcodes. In the following chapters, we will introduce the corresponding setting options and functions in detail and provide the corresponding setting codes...

  • Page 9: Set Code Identification

    9 / 134 Set code identification Instructions for use: In manual barcode reading mode, the operation steps for scanning barcodes are as follows 1. Press and hold the trigger button of the scanner, the line of sight is activated, and a red line of sight appears.

  • Page 10: Enable And Disable The Configuration Code

    10 / 134 Enable and disable the configuration code The setting code can be turned off. When the scanner is set to "Enable setting code" and scanning the setting code, the setting function will take effect. When the scanner is set to "Disable setting code", when scanning the setting code, an error tone of the scan engine will appear and the setting function will not work.

  • Page 11: Restore Factory Default

    11 / 134 Restore factory Default All scanners have a factory default setting. Reading the "Restore Factory Default" setting bar code will make all the scanner's properties setting software default state. Restore factory default Instructions for use: You are most likely to use this barcode in the following situations: 1.

  • Page 12: User Default Settings

    12 / 134 version number User default settings In addition to the factory settings, users can also save their frequently used configuration as user default settings. By scanning "Save user default settings", the current configuration information of the device can be saved as user default settings. If there are already users Default setting information in the module, the new configuration information after this operation will replace the original user default setting information.
  • Page 13 13 / 134 Step 4: Scan the barcode of "disable Setting Code".

  • Page 14: Sound Settings

    14 / 134 Sound settings All tone settings Turn on all sounds Turn off all sounds Power-on prompt sound Turn on or turn off the beep sound when starting up Turn on sound Turn off sound...

  • Page 15: Setting Code Sound

    15 / 134 Setting code sound scan setting code prompt sound on or off Turn on the setting code sound Turn off the setting code sound Prompt sound for reading successful Set the prompt sound on or off after reading code successful Turn on sound for reading successful Turn off sound for reading successful...

  • Page 16: Setting Sound Volume For Reading Successful

    16 / 134 Setting Sound volume for reading successful Set the volume of the prompt sound for reading barcode successful Low sound volume for reading successful Middle sound volume for reading successful High sound volume for reading successful Read successful indicator Setting reading success indicator light Turn on reading successful indicator Turn off reading successful indicator...

  • Page 17: Duration Of The Indicator Light For Reading Barcode Successful

    17 / 134 Duration of the indicator light for reading barcode successful Read the following setting codes, you can modify the LED prompt time, the default time is 200ms. Modify the LED prompt time to 100ms Modify the LED prompt time 200ms Modify the LED prompt time to 500ms Customize and modify LED prompt time Example: Customize and modify the LED prompt time to 300ms, you can set it...

  • Page 18: Lighting Settings

    18 / 134 Lighting settings Fill light illuminator The illuminator can provide auxiliary lighting for shooting and reading, and the light beam illuminates the reading target to improve the reading performance and the ability to adapt to weak ambient light. The user can set it to one of the following states according to the application environment: Turn on the fill light illuminator (default setting): The illuminator lights up during shooting and reading, and goes out at other times.
  • Page 19 19 / 134...

  • Page 20: Aiming Light

    20 / 134 Aiming light The aiming beam can help users find the best reading distance when shooting and reading. Users can choose any of the following modes according to the application environment. The aiming light is turned on by default, and it is blinking. Turn on the aiming light (default setting): The aiming light flashes during shooting and reading, and turn off at other times.

  • Page 21: Data Format

    21 / 134 Data Format Data input format Auto* GBK（GB2312） UTF-8 Data output format GBK code (notepad, Excel, etc.) Unicode code (WORD, QQ, etc.) Raw data output...
  • Page 22 22 / 134...

  • Page 23: Invoice Function

    23 / 134 Invoice function Turn on/off the invoice function Turn on the invoice function Turn off the invoice function...

  • Page 24: Image Recognition Settings

    24 / 134 Image recognition settings Image inversion (reverse white) setting Normal phase bar code: bar code with light background and dark bar Inverted bar code: dark background, light bar code, also known as reverse white bar code, reverse color bar code Allow to read reverse color barcode Prohibit reading reverse color barcode Allows to read 1D reverse color barcodes...
  • Page 25 25 / 134 Allow to read Data Matrix reverse color Prohibit reading Data Matrix reverse color code code Allow to read PDF 417 reverse color code Prohibit reading PDF 417 reverse color code...

  • Page 26: Nr Is Prompted If The Barcode Is Not Successfully Read

    26 / 134 NR is prompted if the barcode is not successfully read Before releasing the trigger button, if the barcode cannot be read within the timeout period, it is allowed to send NR (No Read) message. Any feasible prefix or suffix can be attached to this message Turn on NR Turn off NR...
  • Page 27 27 / 134 Modify NR information Read the following setting codes, and you will start to change the NR information. This setting code needs to be combined and configured with the data code. If you directly read the "save" of the data code, the length of the NR message will be "zero". In this case, even if the NR message is required to be sent, there will be no substantial information content.
  • Page 28 28 / 134 5. Read the data code "Save"; 6. Read the "Disable Setting Code". (If you want to continue using, you can skip this step)

  • Page 29: Chapter 2 Communication Settings

    29 / 134 Chapter 2 Communication Settings Introduction When using this scanner to communicate with different hosts, you need to set the scanner to the corresponding communication interface mode. You can set the scanner's functions by scanning one or more setting bar codes. You can choose to use USB (USB-KBW, USB- COM), TTL, RS232 serial communication interface modes, etc.

  • Page 30: National Keyboard Layout

    30 / 134 National keyboard layout The keyboard key arrangement, symbols, etc. corresponding to different national languages are not the same. The scanner can be virtualized into different national keyboard standards according to actual needs. The keyboard layout setting is applicable to the USB-KBW interface mode, and the default is "American English keyboard"...
  • Page 31 31 / 134 Belgium (Dutch) Turkish-Q...

  • Page 32: Usb Transmission Speed (Delay Between Characters)

    32 / 134 USB transmission speed (delay between characters) This parameter is used to adjust the delay time between scanner barcode characters. When the input host needs slower data transmission, scan the corresponding barcode below to increase the inter-character delay, which can adjust the transmission speed and improve the safety and integrity of output data .

  • Page 33: Usb Polling Speed

    33 / 134 2. Scan the "Custom Delay" setting code; 3. Scan the "1" and "5" setting codes in "Appendix-Data Code"; 4. Scan the "Save" setting code in "Appendix-Save and Cancel Settings"; 5. Scan the "Disable Settings code. USB polling speed The keyboard polling speed can be set to 1~10 ms by the following setting code.
  • Page 34 34 / 134 Polling speed 7ms Polling speed 8ms Polling speed 9ms Polling speed 10ms...

  • Page 35: Usb-Com Virtual Serial Interface

    35 / 134 USB-COM virtual serial interface When the scanner uses a USB connection, and at the same time you want the host to receive data through a serial port, you should use the USB virtual serial port. From the point of view of the host system interface, the scanner is equivalent to connecting with the host through a serial port.

  • Page 36: Usb Hid-Pos Interface

    36 / 134 USB HID-POS interface The USB HID-POS interface is recommended for new application software. Based on the HID interface, no driver is required. USB HID-POS Protocol format vid：0x26f1 pid：0x8803 Host send data format Byte content Message ID (0x04) Effective data length 2-61 data...
  • Page 37 37 / 134 0x00 (no data behind) 0x01 (data behind)

  • Page 38: Data Format Sent By Scanning Device To Host

    38 / 134 Data format sent by scanning device to host Byte content Message ID（0x02） Effective data length 2-57 data 58-62 0x00, 5 bytes reserved 0x00 (no data behind) 0x01 (data behind)

  • Page 39: Ttl/Rs232 Serial Interface

    39 / 134 TTL/RS232 serial interface Serial communication interface is a common way to connect scanners and host devices, and can be used to connect to host devices such as PCs and POS machines. When the scanner uses the serial communication interface, the scanner and the host device must match the serial communication protocol parameter configuration completely to ensure the accuracy of the transmitted data.
  • Page 40 40 / 134...

  • Page 41: Baud Rate

    41 / 134 Baud rate The baud rate is the number of bits transmitted per second in serial data communication. The baud rate used by the scanner and the data receiving host must be consistent to ensure the accuracy of data transmission. The scanner supports the baud rates listed below in bit/s.

  • Page 42: Parity Type

    42 / 134 Parity Type Odd parity ODD Even parity EVEN NONE...

  • Page 43: Chapter 3 Reading Mode

    43 / 134 Chapter 3 Reading Mode Manual reading mode Set to manual reading mode, press the button to start reading, and the reading will not stop when the button is released, the reading will stop if the reading is successful or the reading exceeds the single reading time.

  • Page 44: Manual Reading Mode-The Same Barcode Reading Delay

    44 / 134 Customize and modify the single reading time Example: To set the limit time of a single code reading to 1500ms, you can set it according to the following steps: 1. Scan the "Enable Setting code (you don't need to scan when it is turned on); 2.
  • Page 45 45 / 134 The same barcode reading delay means that after reading a barcode, within the set time, refuse to read the same barcode. Only after the duration has expired can it be read and output. Set to "Reading the same barcode without delay", the same barcode will be output immediately after reading.
  • Page 46 46 / 134 No delay when reading the same barcode Require the same barcode reading delay Reread timeout does not reset Reread timeout reset Read the following setting codes, you can quickly modify the limit value of the same code reading delay time.
  • Page 47 47 / 134 Modify the same code reading delay Custom modify the same code reading 5000ms delay time Example: Set custom and modify the same code reading delay time to 8000ms. 1. Scan the "Start Setting" setting code (you don't need to scan when it is turned on); 2.

  • Page 48: Continuous Reading Mode

    48 / 134 Continuous reading mode After setting, the scanner is in continuous scanning state, without triggering, the reading engine starts to read the code immediately. When the reading is successful, the information is output or the single reading time is over, the reading engine will wait for a period of time (settable) and it will start automatically Read the code once.

  • Page 49: Continuous Reading Mode-Reading Interval Time

    49 / 134 Single reading time 3000MS Single reading time 5000MS Customize and modify the single reading time Example: To set the limit time of a single code reading to 1500ms, you can set it according to the following steps: 1.
  • Page 50 50 / 134 which no acquisition and reading will be performed. The setting range of the reading interval is 0~65535ms, the default time is 1000ms Modify the reading interval to 500ms Modify the reading interval to 1000ms Modify the reading interval to 2000ms Modify the reading interval to 5000ms Customize and modify the reading Modify the reading interval to 0ms...

  • Page 51: Continuous Reading Mode-The Same Barcode Reading Delay

    51 / 134 4. Scan the "Save" setting code in "Appendix-Save and Cancel Settings"; 5. Scan the "Disable Settings" setting code. Continuous reading mode-the same barcode reading delay In order to avoid the same bar code being read multiple times in a short period of time in the continuous reading mode, you can request the reading module to delay the set time in this mode before allowing the same bar code to be read.
  • Page 52 52 / 134...
  • Page 53 53 / 134 No delay when reading the same barcode Require the same barcode reading delay Reread timeout does not reset Reread timeout reset Read the following setting codes, you can quickly modify the limit value of the same code reading delay time.
  • Page 54 54 / 134 Modify the same code reading delay Custom modify the same code reading 5000ms delay time Example: Set custom modification of the same code reading delay time to 8000ms. 1. Scan the "Enable Setting" setting code (you don't need to scan when it is turned on); 2.

  • Page 55: Inductive / Auto-Sensing Reading Mode

    55 / 134 Inductive / auto-sensing reading mode In the auto-sensing mode, the reading module will monitor the captured images. When the scene changes, it will be read within the "single reading time" within a limited time. After the reading is successful, it will output information or time out, and then re-enter the monitoring The state of the scene change.

  • Page 56: Induction Reading Mode-Same Barcode Reading Delay

    56 / 134 Modify the single reading time 3000ms Modify the single reading time of 5000ms Custom modify the limit of single reading time Example: To set the limit time of a single code reading to 1500ms, you can set it according to the following steps: 1.
  • Page 57 57 / 134 The same barcode reading delay means that after reading a barcode, within the set time, refuse to read the same barcode. Only after the duration has expired can it be read and output. Set to "Reading the same barcode without delay", the same barcode will be output immediately after reading.
  • Page 58 58 / 134 No delay when reading the same barcode Require the same barcode reading delay Reread timeout does not reset Reread timeout reset Read the following setting codes, you can quickly modify the limit value of the same code reading delay time.
  • Page 59 59 / 134 Modify the same code reading delay Custom modify the same code reading 5000ms delay time...
  • Page 60 60 / 134 Example: Set custom modification of the same code reading delay time to 8000ms. 1. Scan the "Enable Setting" setting code (you don't need to scan when it is turned on); 2. Scan the setting code of "Customize and modify single reading time"; 3.

  • Page 61: Induction Mode-Image Stabilization Time

    61 / 134 Induction mode-image stabilization time In the induction mode, when the scanner stops reading the code, it will enter a process of re-adapting to the changes in the reading environment (image). After the image is stabilized, it will enter the induction state and wait for the barcode to appear. By modifying the image stabilization timeout, the time to adapt to the environment can be adjusted.
  • Page 62 62 / 134 4. Scan the "Save" setting code in "Appendix-Save and Cancel Settings"; 5. Scan the "Disable Settings" setting code.

  • Page 63: Induction Mode-Sensitivity

    63 / 134 Induction Mode-Sensitivity Sensitivity refers to the degree of change in the detection scene in the induction reading mode. When the reading module judges that the degree of scene change meets the requirements, it will switch from the monitoring state to the reading state. Very high sensitivity High sensitivity Medium sensitivity...

  • Page 64: Chapter 4 Data Editing

    64 / 134 Chapter 4 Data Editing Introduction After the scanner successfully reads the code, the device obtains a string of data, which can be numbers, English, symbols, etc. In practical applications, we may not only need the data information of the bar code, or the data information contained in the bar code cannot meet your needs.
  • Page 65 65 / 134...

  • Page 66: Code Id Settings

    66 / 134 Code ID settings Code ID prefix In the process of using a scanner, you often need to know the type of barcode currently scanned. We can use the Code ID prefix to identify the barcode type. Please refer to "Appendix-Code ID"...

  • Page 67: Custom Code Id

    67 / 134 Custom Code ID The Code ID corresponding to each barcode type can be modified freely. The Code ID of all barcodes is 1 character and must be a letter, and cannot be set as a number, invisible character, or punctuation, etc.
  • Page 68 68 / 134 Modify UPCE0 Code ID Modify UPCE1 Code ID Modify UPCA Code ID Modify IATA25 Code ID Modify Code 39 Code ID Modify Code 93 Code ID Modify Interleaved 2 of 5 Code ID Modify Codabar Code ID Modify Industrial 25 Code ID Modify Matrix 25 Code ID Modify Code 11 Code ID...
  • Page 69 69 / 134 Modify Micro QR Code ID Modify Code32 Code ID Modify ISBN Code ID Modify ISSN Code ID...
  • Page 70 70 / 134 Example: Modify PDF417 Code ID to the letter ‘p’ Example: 1. Look up the table and get the hexadecimal value corresponding to "p" is 70; 2. Scan the "Enable Setting" setting code (you don't need to scan when it is turned on); 3.

  • Page 71: User-Defined Prefix

    71 / 134 User-defined prefix Send user-defined prefix If the user has set a custom prefix, the scanner needs to be set to transmit the custom prefix to transmit the user-defined prefix information. The default is "Do not transmit custom prefixes". Send user-defined prefix Do not transmit user-defined prefixes...

  • Page 72: User-Defined Prefix Setting

    72 / 134 User-defined prefix setting Users can set custom prefixes for different barcode types according to the "Appendix- Code ID" information. Add up to 10 characters for the custom prefix. Set custom prefix Example: Add a custom prefix of XYZ to all barcode types First, query the HEX value corresponding to XYZ as 58,59,5A.

  • Page 73: User-Defined Suffix

    73 / 134 User-defined suffix Send user-defined suffix If the user has set a custom suffix, the scanner needs to be set to transmit the custom suffix to transmit the user-defined suffix information. The default is "Do not transmit custom suffixes". Send user-defined suffix Do not transmit user-defined suffixes...

  • Page 74: User-Defined Suffix Setting

    74 / 134 User-defined suffix setting Users can set custom suffixes for different barcode types according to the "Appendix-Code ID" information. Add up to 10 characters for the custom suffix. Set custom suffix Example: Add a custom suffix of XYZ to all barcode types First, the HEX corresponding to XYZ is only 58,59,5A by querying.

  • Page 75: Hidden Characters

    75 / 134 Hidden characters Step 1: Set the field length Set the length of the Start field Set the length of End field Note: The length of the field is in bytes (1 byte for English characters and 2 bytes for Chinese characters), using hexadecimal data for configuration.

  • Page 76: Step 2: Set The Transmission Field

    76 / 134 Step 6: Scan the "Appendix-Data Code" number "0" "C" setting code in turn; Step 7: Scan the "Save" setting code of "Appendix-Save and Cancel Settings". Step 2: Set the transmission field Transfer complete Data field Only the Start field is transmitted Only transfer the Center field Only the End field is transmitted Example: After setting the complete Data barcode "12345678901234567890", the length of...
  • Page 77 77 / 134...

  • Page 78: End Character Setting

    78 / 134 End character setting The terminator suffix is used to mark the end of a complete data message. The terminator suffix must be the last content when a piece of data is sent, and there will be no additional data after that.

  • Page 79: Custom End Suffix

    79 / 134 Custom end suffix Read the "modify end character" and combine to read the data code to modify the character content of the end character. When modifying end character, use 2 hexadecimal values to represent the characters, and read 2 or 4 values sequentially to represent 1 character or 2 characters.

  • Page 80: Chapter 5 Barcode Parameter Setting

    80 / 134 Chapter 5 Barcode Parameter Setting Introduction Each type of barcode has its own unique attributes, and the scanner can be adjusted to adapt to these attribute changes through the setting codes in this chapter. The fewer barcode types that enable "Allow Reading", the faster the scanning speed of the scanner. You can prevent the scanner from reading unused barcode types to improve the scanner's working performance.

  • Page 81: Turn On/Off All 2D Barcodes

    81 / 134 Turn on all 1D barcodes Turn off all 1D barcodes Turn on/off all 2D barcodes Turn on all 2D barcodes Turn off all 2D barcodes...

  • Page 82: Upc-A

    82 / 134 UPC-A Allow/prohibit reading UPC-A Allow reading UPC-A Prohibit reading UPC-A 传送校验字符 Send check character UPC-A 条码数据固定为 12 字符，第 12 位为校验字符，用于校验全部 12 个字符的正确性，默认为 传送校验字符。 The UPC-A barcode data is fixed to 12 characters, and the 12th digit is the check character, which is used to verify the correctness of all 12 characters.

  • Page 83: Transmission System Characters

    83 / 134 Transmission system characters The first digit of UPC-A barcode is a system character, and its value is fixed as "0" Transmission system characters Do not transmit system characters...

  • Page 84: 2/5 Additional Bits

    84 / 134 2/5 additional bits Additional digits refer to the 2 or 5 digital barcodes appended to the normal barcode, as shown in the figure below. The blue line frame on the left is the normal barcode, and the red line frame on the right is the additional digit.
  • Page 85 85 / 134 Barcode information conversion Barcode information is not converted...

  • Page 86: Upc-E

    86 / 134 UPC-E Allow/prohibit reading UPC-E0 Allow reading UPC-E0 Prohibit reading UPC-E0 Send check character UPC-E0 barcode data is fixed to 8 characters, the 8th digit is a check character, used to verify the correctness of all 8 characters, the default is to transmit a check character. Send check character Do not transmit check characters Transmission system characters...

  • Page 87: Allow/Prohibit Reading Upc-E1

    87 / 134 Allow/prohibit reading UPC-E1 Allow reading UPC-E1 Prohibit reading UPC-E1 Send check character UPC-E1 barcode data is fixed to 8 characters, and the 8th digit is a check character, which is used to verify the correctness of all 8 characters. The default is to transmit a check character.

  • Page 88: 2/5 Additional Bits

    88 / 134 Transmission system characters Do not transmit system characters 2/5 位附加位 2/5 additional bits Additional digits refer to the 2 or 5 digital barcodes appended to the normal barcode, as shown in the figure below. The blue line frame on the left is the normal barcode, and the red line frame on the right is the additional digit.
  • Page 89 89 / 134...

  • Page 90: Allow/Prohibit Reading Ean-8

    90 / 134 EAN-8 Allow/prohibit reading EAN-8 Allow to read EAN-8 Prohibit reading EAN-8 Send check character The EAN-8 barcode data is fixed to 8 characters, and the 8th digit is the check character, which is used to verify the correctness of all 8 characters. The default is to transmit the check character.

  • Page 91: 2/5 Additional Bits

    91 / 134 2/5 additional bits Additional digits refer to the 2 or 5 digital barcodes appended to the normal barcode, as shown in the figure below. The blue line frame on the left is the normal barcode, and the red line frame on the right is the additional digit.

  • Page 92: Allow/Prohibit Reading Ean-13

    92 / 134 EAN-13 Allow/prohibit reading EAN-13 Allow reading EAN-13 Prohibit reading EAN-13 Send check character The EAN-13 barcode data is fixed to 13 characters, and the 13th digit is the check character, which is used to verify the correctness of all 13 characters. The default is to transmit the check character.

  • Page 93: 2/5 Additional Bits

    93 / 134 2/5 位附加位 2/5 additional bits Additional digits refer to the 2 or 5 digital barcodes appended to the normal barcode, as shown in the figure below. The blue line frame on the left is the normal barcode, and the red line frame on the right is the additional digit.

  • Page 94: Convert To Isbn

    94 / 134 Convert to ISBN Barcode information conversion Barcode information is not converted Convert to ISSN Barcode information conversion Barcode information is not converted...

  • Page 95: Code 128

    95 / 134 Code 128 Allow/prohibit reading Code 128 Allow to read Code 128 Prohibit reading Code 128 Code 39 Allow/prohibit reading Code 39 Allow to read Code 39 Prohibit reading Code 39...

  • Page 96: Check Character Setting

    96 / 134 Check character setting Code 39 barcode data is not mandatory to include a check character. If there is a check character, it is the last character of the data. The check character is a value calculated based on all data to check whether the data is correct. You can turn on or off the check according to your needs, and set whether to send check characters.

  • Page 97: Transmission Start Character And End Character

    97 / 134 Transmission start character and end character Code 39 barcode data has a character "*" before and after it is used as the start character and stop character. You can set whether to transmit the start character and stop character together with the barcode data after the barcode is successfully read.
  • Page 98 98 / 134...

  • Page 99: Code 32

    99 / 134 Code 32 Allow/prohibit reading Code 32 Code 32, Code 32 Pharmaceutical, is a form of Code 39 barcode used by Italian pharmacies. This bar code is also called PARAF. The output format of Code 32 is: The output format is: * + A + 8 digits + 1 digit check + *. Allow to read Code 32 Prohibit reading Code 32 Note: Code 32 is converted from Code39 to Code32.

  • Page 100: Code 93

    100 / 134 Code 93 Allow/prohibit reading Code 93 Allow to read Code 93 Prohibit reading Code 93 Codabar（NW-7） Allow/prohibit reading Codabar Allow reading Codabar Prohibit reading Codabar...

  • Page 101: Check Digit Setting

    101 / 134 Check digit setting No verification Modulo 10 verification and transmission Modulo 10 verification and no verification verification Modulo 16 verification and transmission Modulus 16 verification and no verification verification...

  • Page 102: Start Character And Stop Character Setting

    102 / 134 Start character and stop character setting Codabar start and end characters are allowed to be one of the four characters "A", "B", "C", and "D"; the terminator is also allowed to be "T", "N", "*", " E" one of these four characters. The start and end characters are not transmitted by default Do not transmit start and end characters Start and end characters ABCD/ABCD...

  • Page 103: Interleaved Of

    103 / 134 Interleaved 2 of 5 Allow/Prohibit Interleaved 2 of 5 Allow to read Interleaved 2 of 5* Prohibit reading Interleaved 2 of 5 Check character setting Interleaved 2 of 5 barcode data is not mandatory to include a check character. If there is a check character, it is the last character of the data.

  • Page 104: Matrix 2 Of 5

    104 / 134 USS verification and transmission USS verification does not transmit verification verification Matrix 2 of 5 Allow/ Prohibit read Matrix 2 of 5 Allow to read Matrix 2 of 5 Prohibit reading Matrix 2 of 5* Check character setting Matrix 2 of 5 barcode data is not mandatory to include a check character.
  • Page 105 105 / 134 No verification Check and send verification Verify but do not transmit verification...

  • Page 106: Industrial 2 Of 5

    106 / 134 Industrial 2 of 5 Allow/prohibit reading Industrial 2 of 5 Allow to read Industrial 2 of 5 Prohibit reading Industrial 2 of 5 Check character setting Industrial 2 of 5 barcode data does not compulsorily include a check character. If there is a check character, it must be the last byte of the data.
  • Page 107 107 / 134...

  • Page 108: Standard 2 Of 5(Iata)

    108 / 134 Standard 2 of 5(IATA) Allow/prohibit reading Standard 2 of 5 Allow to read Standard 2 of 5 Prohibit reading Standard 2 of 5 Check character setting Standard 2 of 5 barcode data is not mandatory to include a check character. If there is a check character, it must be the last byte of the data.
  • Page 109 109 / 134...

  • Page 110: Code 11

    110 / 134 Code 11 Allow/prohibit reading Code 11 Allow to read Code 11 Prohibit reading Code 11 MSI Plessey Allow/Prohibit reading MSI Plessey Allow to read MSI Plessey Prohibit reading MSI Plessey QR Code Allow/ Prohibit reading QR Code...

  • Page 111: Micro Qr Code

    111 / 134 Allow to read QR Code Prohibit reading QR Code Micro QR Code Allow/prohibit reading Micro QR Code Allow to read Micro QR Code Prohibit reading Micro QR Code Data Matrix Allow/prohibit reading Data Matrix Allow to read Data Matrix Prohibit reading Data Matrix...

  • Page 112: Pdf 417

    112 / 134 PDF 417 Allow/Prohibit PDF 417 Allow to read PDF 417 Prohibit reading PDF 417 Chapter 6 Appendix Appendix-Data Code...
  • Page 113 113 / 134...

  • Page 114: Appendix-Save And Cancel Settings

    114 / 134 Appendix-save and cancel settings After reading the data code, you must read the save code to save the read data. If an error occurs when reading the data code, you can cancel reading the wrong data in addition to resetting.
  • Page 115 115 / 134 Cancel current setting...

  • Page 116: Appendix-Default Setting Table

    116 / 134 Appendix-Default Setting Table Parameter name Default setting Remark Comprehensive settings Setting code function Default Send setting code All tones Power-on prompt Setup code prompt tone Prompt for successful reading Volume of prompt tone for high successful barcode reading Reading success indicator light ON Duration of the indicator light 200ms...
  • Page 117 117 / 134 Data input format Auto Data output format Invoice function Image inversion Prompt for unsuccessful reading Communication settings Interface mode USB-KBW Inter-character delay USB polling speed Keyboard mode American English Control character escape Baud rate 9600 Serial verification No verification Data bit 8 bit...
  • Page 118 118 / 134 Reading mode Manual reading Manual reading mode-single reading time Manual reading mode-the No delay same barcode reading delay Continuous reading mode- single reading time Continuous reading mode- 1000MS reading interval time Continuous reading mode-the No delay same barcode reading delay Induction reading mode-single reading time Induction reading mode-...
  • Page 119 119 / 134 Send Code ID Code ID prefix Code ID+ Custom prefix Send custom prefix Send custom suffix Hide header data Hide central data Hide tail data Allow terminator Terminator Barcode parameter setting Turn on all barcodes Turn on all 1D barcodes Turn on all QR codes UPC-A Allow reading...
  • Page 120 120 / 134 Transmission system characters Read 2 additional bits Read 5 additional bits Convert to EAN-13 UPC-E Allow reading UPC-E0 UPC-E0 transmission system character Allow reading UPC-E1 Send check character UPC-E1 transmission system characters Read 2 additional bits Read 5 additional bits Mandatory additional bits, 2 bits allowed...
  • Page 121 121 / 134 Mandatory additional bits, 5 bits allowed EAN-8 Allow reading Send check character Read 2 additional bits Read 5 additional bits EAN-13 Allow reading Send check character Read 2 additional bits Read 5 additional bits Convert to ISBN Convert to ISSN Code 128 Allow reading...
  • Page 122 122 / 134 Allow reading Turn on verification Transmission check Transmission start character and end character Recognize Full ASCII Code 32 Allow reading Code 93 Allow reading Turn on verification Transmission check Codabar Allow reading Turn on verification Transmission check...
  • Page 123 123 / 134 Transmission start character and end character Start and stop format ABCD/ABCD Interleaved 2 of 5 Allow reading Turn on verification Transmission check Matrix 2 of 5 Allow reading Turn on verification Transmission check Industrial 2 of 5 Allow reading Turn on verification Transmission check...
  • Page 124 124 / 134 Turn on verification Transmission check Code 11 Allow reading MSI Plessey Allow reading QR Code Allow reading Micro QR Code Allow reading Data Matrix Allow reading PDF 417 Allow reading...
  • Page 125 125 / 134 Appendix-Code ID Barcode type Code ID code UPC-A, UPC-E EAN-8, EAN-13,ISBN,ISSN CODE 39，Code 32 Codabar Code 128 Code 93 Interleaved 2 of 5 Matrix 2 of 5 Industrial 2 of 5 Standard 2 of 5 (IATA25) PDF 417 DataMatrix QR Code，Micro QR Code 11...
  • Page 126 126 / 134 Appendix-ASCII code table Note: ASCII code table 0-31 are invisible characters used as control characters, and 32-127 are visible characters Hexadecimal ASCII value character (decimal) NUL (Null char.) SOH (Start of Header)标题开始 STX (Start of Text) 文本开始 ETX (End of Text) 文本结束...
  • Page 127 127 / 134 FF (Form Feed) 格式聩给 CR (Carriage Return) 回车 SO (Shift Out) 移出 SI (Shift In) 移入 DLE (Data Link Escape) 数据传送换码 DC1 (XON) (Device Control 1) 设备控制1（XON） DC2 (Device Control 2) 设备控制2 DC3 (XOFF) (Device Control 3) 设备控制3 （XOFF）...
  • Page 128 128 / 134 FS (File Separator) 文件分隔符 GS (Group Separator)分组符 RS (Request to Send) 记录分隔符号 US (Unit Separator) 单元分隔符 SP (Space) ! (Exclamation Mark) " (Double Quote) # (Number Sign) $ (Dollar Sign) % (Percent) & (Ampersand) ` (Single Quote) ( (Right / Closing Parenthesis) ) (Right / Closing Parenthesis) * (Asterisk)
  • Page 129 129 / 134 , (Comma) - (Minus / Dash) . (Dot) / (Forward Slash) : (Colon) ; (Semi-colon)
  • Page 130 130 / 134 < (Less Than) = (Equal Sign) > (Greater Than) ? (Question Mark) @ (AT Symbol)
  • Page 131 131 / 134 [ (Left / Opening Bracket)
  • Page 132 132 / 134 \ (Back Slash) ] (Right / Closing Bracket) ^ (Caret / Circumflex) _ (Underscore) ' (Grave Accent)
  • Page 133 133 / 134 { (Left/ Opening Brace)
  • Page 134 134 / 134 | (Vertical Bar) } (Right/Closing Brace) ~ (Tilde) DEL (Delete) 删除...

Table of Contents