Table of Contents
Advertisement
en Descaling
6.
To dry the cooking compartment completely, leave
the appliance door open for approx. 1 hour or use
the "Drying" function.
→ "Setting the drying process", Page 36
23 Descaling
To ensure that your appliance continues to operate cor-
rectly, it must be descaled regularly.
How frequently you need to run the descaling pro-
gramme depends on the water hardness and how
many times you have used the steam-assisted opera-
tions. The appliance indicates when only another 5 or
fewer steam-assisted operations are possible. If you do
not carry out descaling, you can no longer set any op-
eration with steam.
Descaling comprises several steps and takes
approximately 70 - 95 minutes:
¡ Descaling (approx. 55 - 70 minutes)
¡ First rinse cycle (approx. 8 - 12 minutes)
¡ Second rinse cycle (approx. 8 - 12 minutes)
Carry out descaling in full.
If descaling is interrupted, you can no longer set any
operation. To ensure that the appliance is ready for op-
eration again, carry out 2 rinse cycles.
23.1 Preparing descaling
ATTENTION!
The length of time for which the descaler is left to work
is based on the recommended, liquid descaler. Other
descalers may damage the appliance.
▶
Only use the liquid descaler recommended by us
for the descaling programme.
If descaling solution comes into contact with the control
panel or other delicate surfaces, it will damage them.
▶
Remove descaling solution immediately with water.
1.
Mix the descaling solution:
200 ml liquid descaler
‒
400 ml water
‒
2.
Open the control panel.
24 Drying
To prevent residual moisture, dry the cooking compart-
ment following operation with steam or microwave-only
operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compartment
floor before operation.
24.1 Drying the cooking compartment
You can dry the cooking compartment by hand or use
the "Drying" function.
1.
Allow the appliance to cool down.
36
3.
Remove the water tank and fill it with descaling solu-
tion.
4.
Once the descaling solution has been poured into
the water tank, slide the tank back in.
5.
Close the control panel.
23.2 Setting the descaling programme
Requirement: → "Preparing descaling", Page 36
1.
Press "Cleaning".
2.
Press "Descaling".
The duration cannot be changed.
3.
Press "Start".
a A message stating that you should carry out the ne-
cessary preparatory work for descaling appears on
the display.
4.
Confirm the message.
a The descaling programme starts and the duration
counts down.
a Once the first part of the descaling programme has
finished, a signal sounds. The appliance prompts
you to carry out 2 rinse cycles.
5.
To rinse the appliance, for each rinse cycle:
Open the control panel and remove the water
‒
tank.
Thoroughly rinse the water tank and fill it with
‒
fresh water.
Slide in the water tank and close the control
‒
panel.
Press "Start" to start the rinse cycle.
‒
a A signal tone sounds when each rinse cycle has
ended.
6.
Once the second rinse cycle is complete:
Empty and dry the water tank.
‒
→ "Emptying the water tank", Page 21
Press
to switch the appliance off.
‒
2.
Remove dirt from the cooking compartment.
3.
Wipe away the water in the cooking compartment.
4.
Dry the cooking compartment.
To dry the cooking compartment, leave the appli-
‒
ance door open for 1 hour.
To use the "Drying" function, set "Drying".
‒
→ "Setting the drying process", Page 36
Setting the drying process
Requirement: → "Drying the cooking compartment",
Page 36
1.
Press "Cleaning".
2.
Press "Drying".
The duration cannot be changed.
Advertisement
Table of Contents
