Table of Contents
Advertisement
Accessories vary from one appliance to another. When
purchasing accessories, always quote the exact
product number (E no.) of your appliance.
7 Before using for the first time
Configure the settings for initial start-up. Clean the appliance and accessories.
7.1 Determining the water hardness before switching on the appliance for the first time
Before using the appliance for the first time, ask your
water supplier about the hardness of your tap water. To
ensure that the appliance can reliably remind you to
descale it when required, you must set your water hard-
ness range correctly.
ATTENTION!
If the wrong water hardness has been set, the appli-
ance cannot remind you to descale it at the right time.
▶
Set the water hardness correctly.
Using unsuitable liquids may damage the appliance.
▶
Do not use distilled water, highly chlorinated tap wa-
ter (>40 mg/l) or other liquids.
▶
Only use cold, fresh tap water, softened water or
non-carbonated mineral water.
Setting
1
0 (softened)
1 (soft)
2 (medium)
3 (hard)
2
4 (very hard)
1
Only set this if you will be using solely softened water.
2
Also set for mineral water. Only use non-carbonated mineral water.
7.2 Performing initial start-up
After connecting the appliance to the power supply,
you must configure the settings for its initial start-up. It
may take a few minutes for the settings to appear on
the display.
Note: You can also use the Home Connect app to con-
figure the settings. When your appliance is connected,
follow the instructions in the app.
1.
Press
to switch the appliance on.
a The first setting appears.
2.
If required, change the setting.
Possible settings:
– Language
– Home Connect
– Time
– Date
– Water hardness
3.
Use
to switch to the next setting.
4.
Work through the settings and make changes as re-
quired.
a After the last setting, a message appears on the dis-
play confirming that the initial start-up is complete.
You can find out which accessories are available for
your appliance in our online shop or from our after-
sales service.
Malfunctions may occur when using filtered or deminer-
alised water. The appliance may request that you top
up the water tank even though it may be full, or opera-
tion with steam is cancelled after approx. two minutes.
▶
Notes
¡ If you are using mineral water, set the water hard-
¡ If your tap water is very hard, we recommend that
Water hardness in
mmol/l
-
Up to 1.5
1.5-2.5
2.5-3.8
Over 3.8
5.
7.3 Cleaning the appliance before using it
for the first time
Before using the appliance to cook food for the first
time, you must clean the cooking compartment and ac-
cessories.
1.
2.
3.
4.
5.
Before using for the first time en
If required, mix filtered or demineralised water with
the bottled non-carbonated mineral water with a ra-
tio of one to one.
ness range to "very hard". If you are using mineral
water, you must only use non-carbonated mineral
water.
you use softened water. If you are using only
softened water, set the "softened" water hardness
range.
German hardness °dH
-
Up to 8.4
8.4-14
14-21.3
Over 21.3
To check the appliance before heating for the first
time, open and close the appliance door once.
Remove the product information and the accessor-
ies from the cooking compartment. Remove any
leftover packaging, such as polystyrene pellets, and
any adhesive tape either in or on the appliance.
Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
Press
to switch the appliance on.
Fill the water tank.
→ "Filling the water tank", Page 19
Apply the following settings:
Type of heating
Temperature
French hardness °fH
-
Up to 15
15-25
25-38
Over 38
4D hot air
Maximum
15
Advertisement
Table of Contents
