Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Planet ICG-2515 Series
Summary of Contents for Planet ICG-2515 Series
- Page 1 Industrial 5G NR Cellular Gateway ICG-2515 Series Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ..............3 2. Requirements ................4 3. Hardware Installation ..............5 3.1 SIM Card Installation ............5 3.2 5G NR Antenna Installation ..........6 3.3 Wi-Fi Antenna Installation (Wi-Fi model) ....... 7 3.4 Wiring the Power Inputs ............8 3.5 Grounding the Device ............ -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET Industrial 5G NR Cellular Gateway, ICG-2515 series. The hardware specifications of these models are as follows: Model Name RJ45 Fiber Wi-Fi ICG-2515-NR ICG-2515W-NR 11ax ICG-2515F-NR ICG-2515FW-NR 11ax “Cellular Gateway” is used as an alternative name in this Quick Installation Guide. -
Page 4: Requirements
2. Requirements z Workstations running Windows 10/XP/2003/Vista/7/8/2008, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/ IP protocols. z Workstations are installed with Ethernet NIC (Network Interface Card). z Ethernet Port Connection Network cables -- Use standard network (UTP) cables with RJ45 connectors. -
Page 5: Hardware Installation
3. Hardware Installation Refer to the illustration and follow the simple steps below to quickly install your Cellular Gateway. 3.1 SIM Card Installation A. Insert an ejector pin into the yellow button next to the tray to loosen the tray. B. -
Page 6: Nr Antenna Installation
3.2 5G NR Antenna Installation Step 1: Connect 5G NR antennas to the 5G NR antenna extender. Cellular ANT2 ANT4 Four SMA female connectors ANT1 ANT3 Step 2: Fasten the 5G NR antenna extenders to the connectors. -
Page 7: Wi-Fi Antenna Installation (Wi-Fi Model)
Step 2: You can bend the antennas to fit your actual needs. Alarm I/O SIM1 SIM2 2.4G Wi-Fi Reset SIM1 RS485 LNK/ Two Wi-Fi SIM2 RP-SMA Connectors WAN/LAN Cellular Signal 1000 10/100 Wi-Fi ICG-2515FW-NR Please use PLANET dual-band Wi-Fi antenna for high effi- ciency to avoid low efficacy. Note... -
Page 8: Wiring The Power Inputs
3.4 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Cellular Gateway is used for two redundant power inputs. Please follow the steps below to insert the power wire. When performing any of the procedures like inserting the wires or tightening the wire-clamp screws, make sure the power is OFF to prevent from getting an electric shock. -
Page 9: Grounding The Device
2. Tighten the wire-clamp screws for preventing the wires from loos- ening. Power 1 Alarm Power 2 The wire gauge for the terminal block should be in the range between 12 and 24 AWG. Note PWR1 and PWR2 must provide the same DC voltage while operating with dual power input. -
Page 10: Wiring The Fault Alarm Contact
3.6 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Cellular Gateway will detect the fault status of the power failure or port failure, and then will form an open circuit. -
Page 11: Starting Web Management
For example, the default IP address of the Cellular Gateway is 192.168.1.1, then the manager PC should be set to 192.168.1.x (where x is a number between 2 and 254), and the default subnet mask is 255.255.255.0. ICG-2515 Series RJ45/UTP Cable PC/Workstation with Device IP IP 192.168.1.x... -
Page 12: Logging In To The Cellular Gateway
4.1 Logging in to the Cellular Gateway 1. Use Web browser and enter IP address http://192.168.1.1 (the factory default IP address or the one that you have just changed in console) to access the Web interface. 2. When the following dialog box appears, please enter the default user name “admin”... - Page 13 3. After entering the password, the main screen appears as shown in Figure 4-3. Figure 4-3: Web-based Main Screen of Cellular Gateway Now, you can use the Web management interface to continue the Cellular Gateway management or manage the Cellular Gateway by console interface.
-
Page 14: Recovering Back To Default Configuration
15 seconds. After the device is rebooted, you can log in the management Web interface within the same subnet of 192.168.1.xx. Reset Button Figure 5-1: ICG-2515 Series Reset Button... -
Page 15: Customer Support
6. Customer Support You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team. PLANET online FAQs: https://www.planet.com.tw/en/support/faq...
Need help?
Do you have a question about the ICG-2515 Series and is the answer not in the manual?
Questions and answers