Related Manuals for SHOWTEC EventMOVE 4/4
Summary of Contents for SHOWTEC EventMOVE 4/4
- Page 1 MANUAL ENGLISH EventMOVE 4/4 Ordercode: 44020 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
EventMOVE 4/4 Table of contents Warning ....................................2 Safety Instructions ................................. 2 Operating Determinations ............................4 Rigging .................................... 4 Connection with the mains............................5 Return Procedure ................................6 Claims ....................................6 Description of the device ..............................7 Frontside..................................7 Backside ..................................8 Installation ................................... -
Page 3: Warning
Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: Showtec EventMOVE 4/4 • Pro power cable (1,5 m) •... - Page 4 • If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
-
Page 5: Operating Determinations
EventMOVE 4/4 • Repairs, servicing and electric connection must be carried out by a qualified technician. • WARRANTY: Till one year after date of purchase. Operating Determinations • This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. -
Page 6: Connection With The Mains
EventMOVE 4/4 The EventMOVE can be placed on a flat stage floor or mounted to any kind of truss with a clamp. Improper installation can cause serious injuries and/or damage of property! Connection with the mains Connect the device to the mains with the power-plug. -
Page 7: Return Procedure
EventMOVE 4/4 Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. -
Page 8: Description Of The Device
EventMOVE 4/4 Description of the device Features The EventMOVE 4/4 is light fixture with high output and great effects. Input voltage: 100-240V, 60/50Hz • Power consumption: 65W • DMX channels: 6, 8, 13 channels • Light source: 4 x 4-in-1 RGBW LEDs •... -
Page 9: Backside
08) Power switch ON/OFF 09) Fuse: T2AL/250V Installation Remove all packing materials from the EventMOVE 4/4. Check if all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly. -
Page 10: Control Modes
EventMOVE 4/4 Control Modes There are 5 modes: • Auto • Manual • Sound-controlled • Master/Slave • DMX-512 (6CH, 8CH, 13CH) One EventMOVE (Auto and Manual) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. -
Page 11: Multiple Eventmoves (Dmx Control)
EventMOVE 4/4 Multiple EventMOVEs (DMX Control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Use a 3-pin XLR cable to connect the EventMOVEs and other devices. -
Page 12: Fixture Linking
EventMOVE 4/4 Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. -
Page 13: Control Panel
EventMOVE 4/4 The EventMOVE 4/4 can be operated with a controller in control mode or without the controller in stand- alone mode. Control Panel A) LCD display MODE button C) SETUP button D) UP button DOWN button Fig. 05 Control Mode The fixtures are individually addressed on a data-link and connected to the controller. -
Page 14: Menu Overview
EventMOVE 4/4 Menu Overview Ordercode: 44020... -
Page 15: Main Menu Options
EventMOVE 4/4 Main Menu Options DMX address settings DMX channel modes Wireless DMX Control modes Manual mode (Static colors) Master/Slave mode Tilt settings Display ON/OFF Software version Reset settings Reset motors 1. DMX address settings With this menu you can set the desired DMX starting address. -
Page 16: Control Modes
EventMOVE 4/4 4. Control modes 01) Press the MODE button until the display shows 02) Press the UP/DOWN buttons to choose the desired control mode. There are 4 available options: DMX-512 mode Auto slow mode Auto fast mode Sound-controlled mode 4.1. -
Page 17: Master/Slave Mode
EventMOVE 4/4 02) Once you have chosen the desired color (RED, GREEN, BLUE or WHITE), press the SETUP button to open the menu. 03) Press the UP/DOWN buttons to increase/decrease the LED brightness. The adjustment range of each color is between 0-255, from dark to brightest. -
Page 18: Dmx Channels
EventMOVE 4/4 DMX Channels 6 channels Channel 1 – Red 0-255 Gradual adjustment Red, from dark to brightest Channel 2 – Green 0-255 Gradual adjustment Green, from dark to brightest Channel 3 – Blue 0-255 Gradual adjustment Blue, from dark to brightest Channel 4 –... -
Page 19: Channels
EventMOVE 4/4 13 channels Channel 1 – Dimmer 0-255 Dimmer intensity, from dark to bright Channel 2 – Strobe Dimmer must be open 0-255 Strobe flash frequency, from OFF to highest frequency Channel 3 – Red Dimmer must be open... -
Page 20: Maintenance
04) The electric power supply cables must not show any damages or material fatigue. The EventMOVE 4/4 requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light output will be significantly reduced. Disconnect the mains power supply, and then wipe the cover with a damp cloth. -
Page 21: No Response To Dmx
EventMOVE 4/4 No Response to DMX Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction. 01) Check the DMX setting. Make sure that DMX addresses are correct. 02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power. -
Page 22: Product Specifications
EventMOVE 4/4 Product Specifications Model: Showtec EventMOVE 4/4 Input voltage: 100-240 VAC, 60/50Hz Power consumption: 65W (full output) DMX linking: 30pcs Fuse: T2AL/250V Dimensions: 323 x 135 x 294 mm (LxWxH) Weight: 6,3 kg Operating and Programming: Signal pin OUT:... -
Page 23: Dimensions
EventMOVE 4/4 Dimensions Ordercode: 44020... - Page 24 ©2015 Showtec...