Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: Showtec Cameleon Bar 24/1 UV Schuko power cable (1,5 m) ...
Page 4
• If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
The Cameleon Bar 24/1 UV can be placed on a flat stage floor or be mounted to a wall. Improper installation can cause serious injuries and/or damage of property!
Cameleon Bar 24/1 UV Connection with the mains Connect the device to the mains with the power-plug. Always check if the right color cable is connected to the right place. International EU Cable UK Cable US Cable BROWN YELLOW/COPPER PHASE...
Cameleon Bar 24/1 UV Description of the device Features The Cameleon Bar 24/1 UV is a LED bar fixture with high output and great effects. Input voltage: 100-240V, 60/50 Hz Power consumption: 60W Light source: 24 x UV LEDs ...
06) Schuko power cable 100-240V OUT Installation Remove all packing materials from the Cameleon Bar 24/1 UV. Check if all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly.
Cameleon Bar 24/1 UV Control Modes There are 4 modes: • Auto mode • Manual mode • Master/Slave • DMX-512 (2CH, 5CH) One Cameleon (Auto mode and Manual) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
Cameleon Bar 24/1 UV Multiple Cameleons (DMX Control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Use a 3-pin XLR cable to connect the Cameleons and other devices.
Cameleon Bar 24/1 UV Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support.
Cameleon Bar 24/1 UV The Cameleon Bar 24/1 UV can be operated with a controller in control mode or without the controller in stand-alone mode. Control Panel A) LED display MODE button C) UP button D) DOWN button Fig. 05 Control Mode The fixtures are individually addressed on a data-link and connected to the controller.
Cameleon Bar 24/1 UV Menu Overview Main Menu Options Auto mode Manual mode DMX-512 mode Master/Slave mode 1. Auto mode With this menu you can adjust the auto mode settings. 01) While in the main menu, keep pressing and holding down the MODE button for 2 seconds, until the display shows 02) Press the MODE button once, to open the menu.
Cameleon Bar 24/1 UV 2. Manual mode With this menu you can set the device’s dimmer and strobe. 01) While in the main menu, press and hold down the MODE button for 2 seconds, until the display shows 02) Press the MODE button once, to open the menu.
04) The electric power supply cables must not show any damages or material fatigue. The Cameleon Bar 24/1 UV requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light output will be significantly reduced. Disconnect the mains power supply, and then wipe the cover with a damp cloth.
01) Power supply. Check that the unit is plugged into an appropriate power supply. 02) The LEDs. Return the Cameleon to your Showtec dealer. 03) The internal fuse. Return the Cameleon to your Showtec dealer. 04) If all of the above appears to be O.K., plug the unit in again.
Page 17
Check if power is switched on and No power to the fixture One or more cables are plugged in fixtures do not function at all • Return the device to your Showtec Internal fuse blown dealer. Fixtures reset The controller is not connected. • Connect controller.