Krups XP2280 Manual page 47

English Français
pass under the steam nozzle. The milk (UHT or pasteurised) and its container should be quite cold.
n As soon as the appliance reaches the right temperature, the
steadily.
n Immerse the steam nozzle into the milk and turn the knob to
Espresso
n The LED and the pictogram remain steady when the steam begins to be produced and can
flash after a few moments.
n For best results, hold the nozzle towards the bottom of the container for about 25 seconds while
the milk heats up (without however touching the bottom of the container). Then, bring the container
down gradually so that the nozzle moves up towards the surface (without the nozzle coming out of
the milk) (Fig. 14).
n Once the froth has been formed, turn the knob to "0" position (Fig. 15). The appliance will now
automatically cool down by launching intermittent pumping cycles. Once this automatic operation is
complete, you can make a coffee.
IMPORTANT : To prevent the steam nozzle from being clogged, the milk foam
must never reach the black plastic upper part.
It is important to clean the steam nozzle after each use to prevent the milk from drying on the inside of
the nozzle. To do this:
n Place the steam nozzle in a container with water and repeat the milk frothing operation for 30 seconds.
WARNING!
The steam nozzle will be hot!
USING THE AUTO-CAPPUCCINO ACCESSORY TO FROTH MILK
The auto-cappuccino accessory makes it easy to prepare a cappuccino or a caffe latte. It comprises a
special dual-position nozzle and a pipe.
n Fill the water tank and turn on the appliance (Fig. 1, 2, 3 and 4).
n Attach the auto-cappuccino accessory firmly to the articulated arm.
n Place a cup under the auto-cappuccino accessory.
n Pour about 100 ml of very fresh, very cold milk into a container.
n Immerse the pipe into the container, or directly into the carton of milk.
WARNING:
Assemble the pipe firmly on the cappuccino accessory (fig.24).
n Turn the accessory's switch to "cappuccino" or "latte" position.
n Press the "steam preheating" button (Fig. 12). During the pre-heating, the
pictogram flash.
n As soon as the appliance reaches the right temperature, the
steadily. Turn the knob to position (Fig. 13). The milk is transferred from the container to the cup.
n Once the froth has been formed, turn the knob to "0" position (Fig. 15). The appliance will now
automatically cool down by launching intermittent pumping cycles. Once this automatic operation is
complete, you can make a coffee.
n To clean the auto-cappuccino accessory, please repeat the procedure for frothing milk, but this time
with 100 ml of water instead of 100 ml of milk.
n For more thorough cleaning of the auto cappuccino accessory, please refer to the section "Cleaning
and Maintenance".
86
Espresso
LED and the pictogram glow
position (fig.13).
Espresso
LED and the
Espresso
LED and the pictogram glow
4 . CLEANING AND MAINTENANCE
Do not wash your espresso machine accessories in the dishwasher.
CLEANING YOUR APPLIANCE
n Unplug the power supply before cleaning and let the appliance cool down.
n Clean the outside of the appliance from time to time with a damp cloth. After use, the water tank
must be emptied.
n Rinse the inside of the tank regularly.
n When a thin white layer starts to form in the tank, carry out a descaling operation (see paragraph 5.
"DESCALING").
CLEANING THE DRIP TRAY
n The drip tray must be emptied after each time the appliance is used. Lift it up slightly and remove it
from the appliance.
n If multiple espressos are prepared one after the other, it should be emptied from time to time (every
7 to 8 espressos approximately) (Fig. 19 & 20).
n The presence of water is normal and is not the sign of a leak.
n If necessary, clean the drip tray and its grid with water and a small amount of gentle washing-up
liquid, rinse and dry. When reassembling the components, make sure everything is in the right place.
CLEANING THE BREWING HEAD AND FILTER HOLDER
n They must be cleaned after each use. Simply wipe a damp cloth over the brewing head (Fig. 21)
and clean the filter holder with clean water and a small amount of gentle washing-up liquid.
n Do not use alcohol- or solvent-based cleaning products.
n For best results, you can press the "EJECT" button several times during rinsing.
We recommend that you shake the filter holder thoroughly in order to remove all the water.
n Rinse and dry.
n When not using your espresso machine, do not leave the filter holder fitted in the appliance in order
to avoid wear to the seal.
For more thorough cleaning, the filter holder can be dismantled fully:
n You can remove the black plastic part where the coffee outlets and the "EJECT" button are found:
turn it to the left and pull sharply (Fig. 22).
n Clean the various components with clean water and a small amount of gentle washing-up liquid.
n Rinse and dry.
n Replace the black plastic part in the metal holder, turn it to the right until the two arrows on each
component line up.
n If the brewing head is heavily clogged up, unscrew the grid using a screwdriver, clean it and refit it
tightening it firmly (Fig. 23).
CLEANING THE STEAM NOZZLE
n This accessory consists of 2 parts: one part which is the plastic support and the other which is the
metal protection cylinder.
n Before cleaning, unlock the nozzle from the articulated arm by turning it to the left (fig.16, 16.2).
n Then slide the metal cylinder along the plastic support (fig.16.3).
n Clean these two parts with tap water and some mild washing-up liquid (fig.17).
n Rinse and dry.
n Once the parts have been properly cleaned, put the metal cylinder back on the support.
n Make sure that you don't damage the silicone seal which makes the nozzle watertight (fig.16.3).
n Insert the nozzle on the articulated arm then lock to the right (fig.18.1, 18.2).
CLEANING THE AUTO CAPPUCCINO ACCESSORY
n For more thorough cleaning, the auto cappuccino accessory can be dismantled into four separate
parts.
n Clean it with water, a little gentle washing-up liquid and a small brush. Rinse and dry it before putting
Français English English
87