Grundig GD-TI-AT30105K Quick Start Manual
  1. Manuals
  2. Brands
  3. Grundig Manuals
  4. Security Camera
  5. GD-TI-AT30105K
  6. Quick start manual

Grundig GD-TI-AT30105K Quick Start Manual

Hide thumbs Also See for GD-TI-AT30105K:
Table of Contents

Advertisement

Quick Links

Download this manual
1

Advertisement

Table of Contents
loading

Related Manuals for Grundig GD-TI-AT30105K

Summary of Contents for Grundig GD-TI-AT30105K

  • Page 2 WWW.GRUNDIG-SECURITY.COM Limitation of Liability / Legal Disclaimer Abetechs GmbH (Grundig Security) undertakes all reasonable efforts to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
  • Page 3 OPEN SOURCE SOFTWARE LICENSE INFORMATION The software components provided with Grundig products may contain copyrighted software that is licensed under various open source software licenses. For detailed information about the contained open source software packages, the used package versions, license information and complete license terms, please refer to the product detail pages on our website www.grundig-security.com.
  • Page 4 Improper use or replacement of the battery may result in the hazard of explosion. Do not use any accessories that are not recommended by GRUNDIG. Do not modify the product in any way. If the product starts to smell or smoke comes out of the device, immediately stop using the product and disconnect it from the power supply to prevent fire or electric shocks.
  • Page 5 liability or responsibility for problems caused by attempted and unauthorized repair and maintenance. Installation Instructions It is necessary to fix the device firmly if the product is installed on a wall or ceiling. Do not install the product on surfaces or in places that are vibrating. Do not install the product near radiation sources.
  • Page 6 Special Installation Instructions for IP Cameras Make sure that the latest firmware is installed on the IP Device. You may get the latest firmware from techsupport@grundig-security.com.

  • Page 7: Table Of Contents

    Table of Contents 1 Camera Introduction ................... 8 1.1 Overview ....................8 1.2 Appearance ..................... 8 1.3 Dimensions (mm) ..................9 2 Operation ....................11 2.1 Installation and cable connection ............11 2.1.1 Installation ..................11 2.1.2 Aviation Plug Installation ..............12 2.1.3 Cable Connection ................

  • Page 8: Camera Introduction

    1 Camera Introduction 1.1 Overview The GD-TI-AT30105K Thermal Positioning System Camera is a series of camera specially designed for long range day and night surveillance. In the daytime, it uses a telephoto lens and high-definition camera imaging, which can take into account both short-range and large-range search and long-distance feature image collection;...

  • Page 9: Dimensions (Mm)

    Figure 1-2 Rear side view 1.3 Dimensions (mm) Figure 1-3 Front View...
  • Page 10 Figure 1-4 Sied vView Figure 1-5 Front and side view of PTZ Figure 1-6 Mounting Hole at the base of PT...

  • Page 11: Operation

    2 Operation 2.1 Installation and cable connection 2.1.1 Installation Mount the pinboard on the camera with M6 × 12 hexagonal screw (already done). Then mount the camera on PTZ with M6 × 20 hexagonal screw. Do not use screws too long in case of damaging the base plate of the camera; Do not use screws too short in case of unsecure installation.

  • Page 12: Aviation Plug Installation

    Make a support according to the chart shown above. Then use suitable bolts and nuts to secure the camera on the support. The support should be able to bear more than 100kg. 2.1.2 Aviation Plug Installation Figure 2-3 Aviation Plug Hole Figure 2-4 Aviation plug Pin When installing, please insert the head hole into the socket, make sure that the pin is inserted into the socket, then twist the upper fixed ring upward and to the right, and...

  • Page 13: Cable Connection

    2.1.3 Cable Connection Figure 2-6 Connection 2.1.4 Connect The interface between the host and PTZ uses a 26-core waterproof aviation connector. For details, please refer to the following: Table 2-1 cable description Pin No. Black White TX+ Purple TX- definition RS485A RS485B (machine)
  • Page 14 Thick definition Yellow 24VAC Note: NC is empty PTZ bottom Output line definitions:...

  • Page 15: Common Faults

    3. Common Faults The table below includes the common faults during operation. Whenever these problems occur, you may refer to this table or contact us directly for proper solution. Fault Possible Cause Solution Power damage or under Replace the original power. power No movement and video after...
  • Page 16 Super high or low default. brightness Inappropriate brightness Adjust brightness, contrast to and contrast parameters adapt to corresponding setting environment or restore default.

  • Page 17: Network Set And Access

    4 Network Set and Access A number of parameters necessitates configuration before using. Parameters need to configured include: IP address, subnet mask and port number. Default IP address for camera: 192.168.1.64 User: admin Password: Abc.12345 Note: The specific login interface is subject to the actual login. 4.1 Accessing by Web Browsers 4.1.1 Product Overview Network thermal imaging is mainly connected with PC through a switch or router.

  • Page 18: Preview

    After the connection is successful, the system displays the Login screen. Figure 4-1 Login Step 2, Enter the password of the admin user. The initial password is Abc.12345. Step 3, Click Login. After the login is successful, the Preview screen is displayed, as shown in Figure 4-2.
  • Page 19 The function bar of the preview interface is introduced, including the system menu bar, the video window adjustment bar, the pan-tilt control option bar, and the pan-tilt function option bar. After logging in to the web page, click the Preview tab. The system displays the Preview interface, as shown in Figure 4-3.
  • Page 20 Icon Function Instruction Single Display a single screen screen Dual screen Display dual picture Four Display four screens pictures Main code Play the main code stream with high definition stream Secondary Play the secondary code stream with low resolution code stream Capture Click this icon to grab a current video screen and save it in the set storage path.
  • Page 21 and then the camera will suppress the corresponding point to the center of the video. Hold down the left- mouse button and pull out a rectangular area to the right (up) direction, and then camera will suppress the corresponding point to the center of the video to zoom in the view.
  • Page 22 Icon Instruction Long press the arrow keys to control the pan/tilt to rotate horizontally and vertically. Adjust the panning speed of the PTZ. Adjust the tilt rotation speed of the PTZ. Adjust the focus speed of the lens Indicates "Zoom+" and "Zoom-". When you press and hold "+", the lens is zoomed in and the scene is enlarged;...
  • Page 23 Step 1 Click the "PT" tab and select "Preset"; Step 2 Select the preset number and enter the name; Step 3 Control the lens and PTZ to the specified position; Step 4 Click "Set" to complete the configuration. Click the "Call" icon to move the camera to the position corresponding to the preset, and click the "Delete"...
  • Page 24 4.1.3.6 Scan Figure 4-8 Scan After setting the scan, turn on the scan, the device will automatically scan back and forth between the set left border and right border at a certain speed. Step 1 Click the "PT" tab and select “Scan”. Step 2 Control the PTZ to a certain position, and click the "Left "...
  • Page 25 Figure 4-9 General settings Note： Please refer to the actual operation interface. Some functions require device support. Please refer to the actual product. 4.1.3.8 Alarm...

  • Page 26: Image Settings

    Figure 4-10 Alarm settings Note：  Please refer to the actual operation interface. Some functions require device support. Please refer to the actual product.  The corresponding detection must be configured under " ", and it will be valid only if it is enabled in this interface, otherwise it will be invalid.
  • Page 27 PTZ: Select "Settings→ Channels Settings→ Image Settings", the image settings include Image parameter settings, ODS settings, Thermal parameter settings, Bad point correction, Thermal status. 4.1.4.1 Image parameter Switch to Settings→ Channels Settings → Image Settings→ Image Parameter. In channel 1, the visible light image parameter settings include Basic Parameter, Exposure, Focus Parameter, Day Night, Backlight, White Balance, Enhance, Video Adjust, Dual Video, ROI Zoom.
  • Page 28  Defog: When the device is in a foggy or hazy environment, the image quality will decrease. After enabling this function, the recognizable degree of objects in the water fog weather video screen can be improved to a certain extent. ...
  • Page 29 4.1.4.2 Thermal Parameter Figure 4-14 Thermal Parameter  Graphic Adjustment Thermal imaging parameter image adjustment, adjust the image according to the actual environment needs, as shown in the figure. Figure 4-15 Graphic Adjustment...
  • Page 30 Please refer to the table below for some detailed function descriptions. Function Description Brightness Linearly adjusts the overall brightness of the image. The larger the value, the brighter the image, and vice versa. Contrast Adjust the contrast of the image. The larger the value, the larger the contrast of the image, and the smaller the contrast.
  • Page 31 Please refer to the table below for some detailed function descriptions. Function Description Manual Calibration Click this button to manually calibrate once. Background Calibration Click this button to correct the background once. Before using this function, you must aim the camera at the scene with a single background.
  • Page 32 Figure 4-18 Anti sunburn Please refer to the table below for some detailed function descriptions. Function Description Enable After ticking, enable and enable the function Mode Auto Baffle: trigger the rear shutter to block the photosensitive film Auto Elude: after triggering, the PTZ rotates one field of view to the right Image Pixel Threshold The smaller the value, the more sensitive.

  • Page 33: Alarm Settings

     Other Figure 4-19 Other Please refer to the table below for some detailed function descriptions. Function Description Display High Temperature The video screen will superimpose the reference temperature and the maximum temperature. After closing, it is not displayed. The temperature value can be adjusted by adjusting the transmittance and response rate.
  • Page 34 Figure 4-20 Intrusion setting Please refer to the table below for detailed function descriptions. Function Description Channel Channel 1 sets visible light intelligent analysis rules; Channel 2 sets thermal imaging intelligent analysis rules Intrusion Detection After opening, after the target enters the area, an alarm Enable will be triggered Object Marking...
  • Page 35 Function Description PTZ Follow Up After enabling this function, the drawn area will move synchronously with the PTZ, and the virtual area will always be consistent with the actual area. Trail analysis After this function is enabled, the target recognition frame will be drawn when the system continues to detect a target for more than the "minimum track duration"...
  • Page 36 "Deployment time" and "Linkage method" can be set and operated on the corresponding interface according to your needs. 4.1.5.1.2 Cross-line The Cross-line detection function can detect whether there is an object crossing the set warning surface in the video, and link the alarm according to the judgment result. Select "Settings →...

  • Page 37: Hot Alarm

    Function Description Preset Senario Can be associated with presets Sensitivity The higher the sensitivity, the easier it is to detect moving objects, but at the same time the higher the false alarm Detection Mode Support Both, A to B direction, B to A direction Maximum Size Maximum size of detected target Minimum Size...
  • Page 38 Figure 4-22 Hot alarm Please refer to the table below for detailed function descriptions. Function Description Hot Alarm Enable After it is turned on, it will alarm when a hot target is detected Object Marking When turned on, hot targets can be seen in the video Preset Scenario Linkable presets...

  • Page 39: Ptz

    4.1.7 PTZ  PTZ Settings Switch to Settings → PTZ→ Normal Settings → PTZ Settings. Figure 4-23 PTZ Settings Please refer to the table below for some detailed function descriptions. Function Description General (channel) Channel 1 sets visible light, channel 2 sets thermal imaging Lens Focus Input the lens focus value, click the focus position, the lens focus will be automatically positioned to the set position...
  • Page 40 Function Description PTZ Warm After clicking, the PTA warms up and is used when the device is frozen Horizontal\Vertical After it is turned off, the pan and tilt motors cannot be driven to Drive rotate. After it is turned on, the pan and tilt motors can be driven to rotate.

Table of Contents