Advertisement
CONTENTS:
Part 1 - Planning the Installation
Part 2 - Electrical Connection
Part 3 - Direction of Vent and Securing the Hood
Part 4 - Use & Care
Before beginning installation, please thoroughly read and become familiar with these instructions. Installation and
service must be completed by a qualified installer. Failure to properly install this product may void the warranty.
Please be advised that the T7200 Series BBQ Hood MAY NOT be installed on a Patio or Lanai area that does not
have a roof over the BBQ Hood to protect it from direct rain or potential water ingress. This Hood should be
installed with a MINIMUM of three (3) feet of weather proof roof coverage on all sides that are not protected from
direct rain by an adjacent wall.
It is required that all duct work and roof openings be thoroughly sealed with the applicable tape and/or roof sealant
to prevent ingress of water.
Installer:
Please leave Installation Instructions with the BBQ hood owner.
Please keep Installation Instructions for local electrical inspector's use and for future reference.
Owner:
WARNINGS: Must be followed carefully to avoid personal injury.
IMPORTANT: Must be followed carefully to avoid damage or incorrect installation.
TIPS: Contain helpful information to facilitate installation.
Revised 11/19/20
Copyright (C) 2020 Trade-Wind Manufacturing, LLC
INSTALLATION INSTRUCTIONS &
Trade-Wind
T7200 Series Models:
No Blower
1200 CFM
T7236
T7236-12
T7242
T7242-12
T7248
T7248-12
USE & CARE GUIDE
®
T7200 Series BBQ Hood
Proverbs 22:29
Page 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Trade-wind T7200 Series
Summary of Contents for Trade-wind T7200 Series
- Page 1 Failure to properly install this product may void the warranty. Please be advised that the T7200 Series BBQ Hood MAY NOT be installed on a Patio or Lanai area that does not have a roof over the BBQ Hood to protect it from direct rain or potential water ingress.
- Page 2 1. Consult a licensed ventilation contractor or qualified technician for proper installation of exhaust ducting. Locate the cooking area for minimum cross drafts-away from doors and windows, when possible. Revised 11/19/20 Copyright (C) 2020 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 2...
-
Page 3: Planning The Installation
3. Consult a licensed ventilation contractor or qualified technician for proper installation of exhaust ducting. 4. Locate the cooking area for minimum cross drafts—away from doors and windows, when possible. Revised 11/19/20 Copyright (C) 2020 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 3... -
Page 4: Front View
These 10” elbows can be purchased at many Home and Hardware stores for a nominal cost. Fig. 3 Fig. 4 Revised 11/19/20 Copyright (C) 2020 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 4... -
Page 5: Electrical Connection
15 or 20 Amp circuit breaker. The T7200 Series BBQ Hood is supplied with a 6.0 Amp three speed fan control. For safety precautions, each Ventilation Hood should be installed in a GFCI protected branch circuit. - Page 6 Hoods are designed for halogen light bulbs. They can be purchased at most home and/or grocery stores. We endeavor to incorporate the best technology provided to our industry, in manufacturing the Trade-Wind products, therefore, we reserve the right to change models, mode of operation, and specification without prior notice.
-
Page 7: Warranty
T7200 BBQ Hood Ventilation Products What is Covered Trade-Wind warrants its T7200 Series BBQ Hood ventilation products to the original user, to be free of defects in materials and workmanship for three (3) years from the date of purchase. Trade-Wind at its option, will repair or replace the complete unit or any defective component without charge. This warranty may be voided if any unauthorized service, alterations, or repairs are made to the product. - Page 8 In ventilation systems utilizing a roof cap or wall cap with a built-in damper, remove it. Dampers are unnecessary and will cause increased static pressure (air resistance), that may result in rattling, vibration and air buffeting noises, as well as inadequate ventilation. Revised 11/19/20 Copyright (C) 2020 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 8...
- Page 9 The “radius” is one-half the diameter of a round duct, e.g., ½ of a 10” round duct is 5”. 3.1416 is “Pi”, the “constant” used when calculating the area of a circle. Revised 11/19/20 Copyright (C) 2020 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 9...
- Page 10 Roof Cap Drawing *Required dimensions for roof cap - Minimizes static pressure and maximizes air flow to ensure optimum performance of your Trade-Wind product. product. Revised 11/19/20 Copyright (C) 2020 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 10...
Need help?
Do you have a question about the T7200 Series and is the answer not in the manual?
Questions and answers