Subscribe to Our Youtube Channel
Related Manuals for Trade-wind I3200 Series
Summary of Contents for Trade-wind I3200 Series
- Page 1 ***ATTENTION*** PLEASE REMOVE THE RIGHT SIDE BAFFLE FILTER TO LOCATE YOUR NEW REMOTE CONTROL. Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 1...
- Page 2 Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 2...
- Page 3 -- For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. WARNING – TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 3...
- Page 4 To reduce the risk of fire and to properly exhaust air, be sure to duct air outside – Do not vent exhaust air into spaces with in walls or ceilings or into attics, crawl spaces, or garages. Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 4...
-
Page 5: Planning The Installation
1. Center of electrical access is 7" from the front & 2 2. Vent is centered left to right. Damper is not included. ” larger than above dimensions. 3. Length & width cutouts should be Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 5... - Page 6 Replacing the filter is just as easy as taking it out. For visual instructions on how to remove the filters visit our YouTube page (https://www.youtube.com/channel/UCwVIbi_9hbuIATTYvz43oBA). Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 6...
-
Page 7: Range Of Remote Control
The infrared transmitter at the top of the remote must be pointed in the direction of the electronic control at the right front of your hood or liner. Range distance will vary depending on your installation, but see diagram below for approximate range area. Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 7... -
Page 8: Wiring Diagram
The neutral wire (white) must only be connected to the white neutral wire coming in from the electrical panel. Wiring Diagram Diagram 1: All Models with Factory Installed Internal Motor/Blower House Electrical Panel Green White 120V Black Liner Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 8... -
Page 9: Warranty
What is NOT Covered: Normal maintenance and service of any product that has been subject to misuse, negligence, ® accident, or installation inconsistent with the recommended Trade-Wind Installation Instructions ® and Trade-Wind Best Practices Guidelines. -
Page 10: Best Practices
As previously mentioned, improperly installed duct pipe will cause excessive static pressure (air resistance), that may result in rattling, vibration and air buffeting noises, as well as inadequate ventilation. Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 10... - Page 11 In-line dampers must be installed so that the exhaust air flow will open the butterfly blades. Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 11...
- Page 12 The “radius” is one-half the diameter of a round duct, e.g., ½ of a 10” round duct is 5”. 3.1416 is “Pi”, the “constant” used when calculating the area of a circle. Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 12...
Need help?
Do you have a question about the I3200 Series and is the answer not in the manual?
Questions and answers