Advertisement
Quick Links
L7200 Series Models:
No Blower
1200CFM
L7236
L7236-12
L7242
L7242-12
L7248
L7248-12
L7254
L7260
L7266
L7272
CONTENTS:
Part 1 - Planning The Installation
Part 2 - Electrical Connection
Part 3 - Direction of Vent and Securing The Liner
Part 4 - Use & Care
Before beginning installation, please thoroughly read and become familiar with these instructions. Installation and
service must be completed by a qualified installer. Failure to properly install this product may void the warranty.
Please be advised that the Trade-Wind
that does not have a roof over the Range Hood to protect it from direct rain or potential water ingress. This Liner
should be installed with a MINIMUM of three (3) feet of weather proof roof coverage on all sides that are not
protected from direct rain by an adjacent wall.
It is required that all duct work and roof openings be thoroughly sealed with the applicable tape and/or roof sealant
to prevent ingress of water.
Installer:
Please leave Installation Instructions with the BBQ Liner owner.
Please keep Installation Instructions for local electrical inspector's use and for future reference.
Owner:
WARNINGS: Must be followed carefully to avoid personal injury.
IMPORTANT: Must be followed carefully to avoid damage or incorrect installation.
TIPS: Contain helpful information to facilitate installation.
WARNING! TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO
PERSONS OBSERVE THE FOLLOWING:
a) Use this unit only in the manner intended by the manufacturer. If you have any questions, please contact the
manufacturer at the address or telephone number listed in the warranty.
b) Before servicing or cleaning unit, switch power off at service panel and lock service panel and lock the service
disconnection means to prevent power from being switch on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device, such as a tag to the service panel.
Revised 6/11/18
2300CFM
N/A
N/A
N/A
N/A
L7254-23
N/A
L7260-23
N/A
L7266-23
N/A
L7272-23
®
L7200 Series BBQ Liner MAY NOT be installed on a Patio or Lanai area
READ AND SAVE THESE INSTRUCTIONS
Copyright © 2018 Trade-Wind Manufacturing, LLC
INSTALLATION INSTRUCTIONS &
USE & CARE GUIDE
®
Trade-Wind
L7200 Series BBQ Liner
Proverbs 22:29
Page 1
Advertisement
Related Manuals for Trade-wind L7200 Series
Summary of Contents for Trade-wind L7200 Series
- Page 1 Please be advised that the Trade-Wind L7200 Series BBQ Liner MAY NOT be installed on a Patio or Lanai area that does not have a roof over the Range Hood to protect it from direct rain or potential water ingress. This Liner should be installed with a MINIMUM of three (3) feet of weather proof roof coverage on all sides that are not protected from direct rain by an adjacent wall.
- Page 2 3. The ducting must be air tight. Use a minimum of 2 sheet metal screws at every duct joint. Then, seal the duct joints with high quality duct tape. 4. Do not use this unit with any solid-state speed control device. 5. This unit must be grounded. Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 2...
-
Page 3: Planning The Installation
TRADE-WIND IMPORTANT: If the L7200 Series BBQ Liner is installed as a liner for a wood hood, proper installation of the hood as a Liner is directly related to the material from which the custom canopy is constructed. You must provide structural framing and tight backing in the areas in which you are securing the Liner inside your custom canopy. - Page 4 Follow all instructions regarding minimum safe clearances and installation location. Failure to do so may result in a safety hazard or fire. To reduce the risk of fire use only metal ductwork. Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 4...
-
Page 5: Electrical Connection
15 or 20 Amp circuit breaker. ® TRADE-WIND L7200 Series BBQ Liner is supplied with a 6.0 Amp three speed fan control. For safety precautions, each Ventilation Liner should be installed in a GFCI protected branch circuit. INSTRUCTIONS: Wire connections: (See Diagram Below) There are 3 wires on the front panel that require connection. - Page 6 TRADE-WIND Because the L7200 Series BBQ Liner was designed for all applications, no mounting holes have been pre-drilled. This allows for custom applications for mounting. The Liner should be attached to the framing through the top and back, whenever possible. Remove the filters. Mark and drill screw holes through the Liner as required.
-
Page 7: Warranty
What is NOT Covered: Normal maintenance and service of any product that has been subject to misuse, negligence, ® accident, or installation inconsistent with the recommended Trade-Wind Installation Instructions ® and Trade-Wind Best Practices Guidelines. - Page 8 In ventilation systems utilizing a roof cap or wall cap with a built-in damper, remove it. Dampers are unnecessary and will cause increased static pressure (air resistance), that may result in rattling, vibration and air buffeting noises, as well as inadequate ventilation. Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 8...
- Page 9 The “radius” is one-half the diameter of a round duct, e.g., ½ of a 10” round duct is 5”. 3.1416 is “Pi”, the “constant” used when calculating the area of a circle. Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 9...
- Page 10 Roof Cap Drawing *Required dimensions for roof cap - Minimizes static pressure and maximizes air flow to ensure optimum performance of your Trade-Wind product. Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 10...
Need help?
Do you have a question about the L7200 Series and is the answer not in the manual?
Questions and answers