Advertisement
7200 Series Models:
No Blower 1200 CFM
7236
7236-12
7242
7242-12
7248
7248-12
7254
N/A
7260
N/A
7266
N/A
7272
N/A
CONTENTS:
Part 1 - Planning The Installation
Part 2 - Electrical Connection
Part 3 - Direction of Vent and Securing The Hood
Part 4 - Use & Care
Before beginning installation, please thoroughly read and become familiar with these instructions. Installation and
service must be completed by a qualified installer. Failure to properly install this product may void the warranty.
Please be advised that the Trade-Wind
that does not have a roof over the BBQ Hood to protect it from direct rain or potential water ingress. This Hood
should be installed with a MINIMUM of three (3) feet of weather proof roof coverage on all sides that are not
protected from direct rain by an adjacent wall.
It is required that all duct work and roof openings be thoroughly sealed with the applicable tape and/or roof sealant
to prevent ingress of water.
Installer:
Please leave Installation Instructions with the BBQ hood owner.
Please keep Installation Instructions for local electrical inspector's use and for future reference.
Owner:
WARNINGS: Must be followed carefully to avoid personal injury.
IMPORTANT: Must be followed carefully to avoid damage or incorrect installation.
TIPS: Contain helpful information to facilitate installation.
WARNING! TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO
PERSONS OBSERVE THE FOLLOWING:
a) Use this unit only in the manner intended by the manufacturer. If you have any questions, please contact the
manufacturer at the address or telephone number listed in the warranty.
b) Before servicing or cleaning unit, switch power off at service panel and lock service panel and lock the service
disconnection means to prevent power from being switch on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device, such as a tag to the service panel.
Item No. 0BL-00-010
Rev. 9/19/2017
2300CFM
N/A
N/A
N/A
7254-23
7260-23
7266-23
7272-23
®
7200 Series BBQ Hood MAY NOT be installed on a Patio or Lanai area
READ AND SAVE THESE INSTRUCTIONS
Copyright (C) 2017, Universal Metal Industries, Inc.
INSTALLATION INSTRUCTIONS &
USE & CARE GUIDE
®
Trade-Wind
7200 Series BBQ Hood
Prov. 22:29
Page 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Trade-wind 7200 Series
Summary of Contents for Trade-wind 7200 Series
- Page 1 Please be advised that the Trade-Wind 7200 Series BBQ Hood MAY NOT be installed on a Patio or Lanai area that does not have a roof over the BBQ Hood to protect it from direct rain or potential water ingress. This Hood should be installed with a MINIMUM of three (3) feet of weather proof roof coverage on all sides that are not protected from direct rain by an adjacent wall.
- Page 2 CAUTION -- For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. WARNING – TO REDUCE THE RISK OF A BBQ TOP GREASE FIRE: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite.
-
Page 3: Planning The Installation
Ducted fans must always be vented to the outdoors. e) For safe and secure wall mounting, the TRADE-WIND ® BBQ Hood should be mounted to a solid vertical surface of sufficient width to allow for mounting of the Hood. The horizontal surface should extend from a vertical plane to the point directly in front of the exhaust roof cap (or wall cap). -
Page 4: Front View
IMPORTANT: All dimensions are nominal +/- 1/8”. FRONTVIEW Model # (No Blower) (1200 CFM) 7236 7236-12 7242 7242-12 7248 7248-12 FRONTVIEW Model # (No Blower) (2300 CFM) 7254 7254-23 7260 7260-23 7266 7266-23 7272 7272-23 Item No. 0BL-00-010 Rev. 9/19/2017 Copyright (C) 2017, Universal Metal Industries, Inc. -
Page 5: Electrical Connection
15 or 20 Amp circuit breaker. ® TRADE-WIND 7200 Series BBQ Hood is suppliedwith a 6.0 Amp three speed fan control. For safety precautions, each Ventilation Hood should be installed in a GFCI protected branch circuit. INSTRUCTIONS: Wire connections: (See Diagram Below) There are 3 wires on the front panel that require connection. - Page 6 TRADE-WIND Because the 7200 Series BBQ Hood was designed for all applications, no mounting holes have been pre-drilled. This allows for custom applications for mounting. The hood should be attached to the framing through the top and back, whenever possible. Remove the filters. Mark and drill screw holes through the hood as required.
-
Page 7: Warranty
TRADE-WIND Universal Metal Industries, Inc., warrants its 7200 Series BBQ Hood ventilation products to the original user, to be free of defects in materials and workmanship for three (3) years from the date of purchase. Universal Metal Industries, Inc., at its option, will repair or replace the complete unit or any defective component without charge. - Page 8 Best Practices Instructions Venting Installation Instructions Model: 7200 Series IMPORTANT: Problems caused by improper installations are not covered by the manufacturer’s warranty. IMPORTANT: Undersized and improperly installed duct pipe and/or other ventilation components will cause excessive static pressure (air resistance), that may result in rattling, vibration and air buffeting noises, as well as inadequate ventilation.
- Page 9 Roof Caps and Wall Caps The roof cap or wall cap is the termination point of the venting system that allows the exhaust air to exit to the outdoors. All sections of this fitting must have an equal or greater air path area than the ventilator’s discharge port. If any section of the roof cap or wall cap is smaller than the ventilator’s discharge port, the entire ventilation system will lose efficiency and the restriction will cause increased static pressure and decrease performance.
- Page 10 Roof Cap Drawing *Required dimensions for roof cap - Minimizes static pressure and maximizes air flow to ensure optimum performance of your Trade-Wind product. Item No. 0BL-00-010 Rev. 9/19/2017 Copyright (C) 2017, Universal Metal Industries, Inc.
Need help?
Do you have a question about the 7200 Series and is the answer not in the manual?
Questions and answers