Related Manuals for Lattice Semiconductor Himax HM01B0
Summary of Contents for Lattice Semiconductor Himax HM01B0
- Page 1 Himax HM01B0 UPduino Shield Based Hand Gesture Detection Demo User Guide FPGA-UG-02076 Version 1.0 October 2018...
-
Page 2: Table Of Contents
Figure 5.2. Uart Example of Open Hand ..........................9 © 2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. -
Page 3: Acronyms In This Document
Universal Serial Bus © 2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. -
Page 4: Introduction
User Guide 1. Introduction The Lattice Himax HM01B0 UPduino Shield Based Hand Gesture Detection Demo User Guide describes how to operate the Hand Gesture demo on the Himax HM01B0 UPduino Shield board. This design features a Convolutional Neural Network (CNN), using the Compact CNN Accelerator soft IP, which is used in hand gesture. -
Page 5: Programming The Hand Gesture Demo
4. Programming the Hand Gesture Demo This section provides the procedure for programming the SPI Flash on the Himax HM01B0 UPduino Shield Board. Two different files should be programmed into the SPI Flash. These files are programmed to the same SPI Flash, but at different addresses: ... -
Page 6: Figure 4.2. Bitstream File Settings
Click OK. © 2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. -
Page 7: Figure 4.3. Binary Firmware File Settings
11. After programming the files, perform a power cycle in order to start observing the demo. © 2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. -
Page 8: Running The Hand Gesture Demo
Figure 5.1. Camera and LED Location © 2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. -
Page 9: Figure 5.2. Uart Example Of Open Hand
Figure 5.2. Uart Example of Open Hand © 2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. -
Page 10: Technical Support
Initial release. © 2018 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. - Page 11 Floor, 111 SW 5 Avenue Portland, OR 97204, USA T 503.268.8000 www.latticesemi.com...
Need help?
Do you have a question about the Himax HM01B0 and is the answer not in the manual?
Questions and answers