System Memory; Installing The Dimm Module - DFI CMS330-Q470E User Manual

Microatx industrial motherboard
Table of Contents

Advertisement

X System Memory
JP4/2/3/1
(top to bottom)
USB 7/8
2
6
1
(USB 2.0)
5
1
5
2
6
+12V Power
1
5
2
6
1
5
2
6
VGA
1
5
HDMI
DP
LAN1
USB 1/2
(USB 3.2 Gen 2)
LAN2
USB 3/4
(USB 3.2 Gen 1)
USB 7/8/9/10
(USB 3.2 Gen 1)
Mic In
Line Out
Line In
Note
2280
2260
2242
PCIE1 (PCIe x16)
PCI1
LAN LED
Buzzer
8
7
PCI2
2
1
1
2
J12
PCIE2 (PCIe x4)
2
Front
9
10
Audio
1
5
(USB 2.0)
DIO Power
SYS FAN3
1
19
3
3
3
1
1
1
4
1
S/PDIF
2
10
2
1
1
1
Digital I/O (DIO)
JP13/11/25
USB 9/10 (USB 2.0)
(left to right)
The system board supports the following memory interface.
Single Channel (SC)
Data will be accessed in chunks of 64 bits from the memory channels. DIMMs are on the same
channel. DIMMs in a channel can be identical or completely different. However, we highly rec-
ommend using identical DIMMs. Not all slots need to be populated.
Dual Channel (DC)
Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides
better system performance because it doubles the data transfer rate.
Features
Four 288-pin DIMM up to 128GB (Q470E) / Two 288-pin DIMM up to
64GB (H420E)
Dual Channel DDR4 2400/2666/2933 MHz
User's Manual | CMS330-Q470E/H420E
SYS FAN1 CPU FAN1
DDR4_3
DDR4_4
1
1
9
1
J34
Battery
9
1
J35
2
LGA 1200
14
13
9
1
J36
2
1
9
1
LPC
J37
12
24
ATX
power
Standby
Power
LED
1
13
1
2
Front
Panel
11
SYS FAN2
M.2 M Key
1
SPI Flash
BIOS
DDR4_1
DDR4_2
SATA0/1/2/3
(top to bottom)
1
3
JP5
HDDPWR
3
4
Intel
JP26
1
1
USB 3.2 Gen1
JP24
(USB 5/6)
H420E/Q470E
1
2
1
10
J10
SOJ2
5
6
9
1
1
1
9
1
20
11
M.2 E Key
USB 11/12
2230
9
1
Note
COM 6
9
1
9
1
1
10
2
2
2
COM2/3/4/5
(top to bottom)

System Memory

X

Installing the DIMM Module

Before installing the memory module, please make sure that the following safety cautions are
well-attended.
Make sure the PC and all other peripheral devices connected to it has been powered
down.
DDR4_1
DDR4_2
Disconnect all power cords and cables.
DDR4_3
Locate the DIMM socket on the system board
DDR4_4
Make sure the notch on memory card is aligned to the key on the socket.
Eject Tab
HARDWARE INSTALLATION
Memory Module
Notch
Socket Top View
Key
Eject Tab
Socket Side View
Chapter 2
11

Advertisement

Table of Contents
loading

This manual is also suitable for:

Cms330-h420e

Table of Contents