Related Manuals for turck FS100 L Series
Summary of Contents for turck FS100 L Series
- Page 1 Your Global Automation Partner FS100…L…-2UPN8 Flow Sensors Instructions for Use...
-
Page 2: Table Of Contents
LED indicator bar — flow monitoring............... 17 LED indicator bar — temperature monitoring............ 17 LEDs — diagnostic messages .................. 18 V02.00 | 2022/08 | 2 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... - Page 3 12 Repair .............................. 29 12.1 Returning devices ...................... 29 13 Disposal.............................. 29 14 Technical data........................... 30 15 Turck subsidiaries — contact information.................. 32 V02.00 | 2022/08 | 3 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
- Page 4 Contents V02.00 | 2022/08 | 4 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
-
Page 5: About These Instructions
If you have any suggestions for improving the design or if some information is missing in the document, please send your suggestions to techdoc@turck.com. V02.00 | 2022/08 | 5 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 6: Notes On The Product
Two seals (not on devices with NPT and R threads) Quick Start Guide Turck service Turck supports you with your projects, from initial analysis to the commissioning of your applic- ation. The Turck product database under www.turck.com contains software tools for program- ming, configuration or commissioning, data sheets and CAD files in numerous export formats. -
Page 7: For Your Safety
The product is designed according to state-of-the-art technology. However, residual risks still exist. Observe the following warnings and safety notices to prevent damage to persons and property. Turck accepts no liability for damage caused by failure to observe these warning and safety notices. -
Page 8: Product Description
ø 7.3 14.5 N3/4“ ø 7.3 Fig. 5: Dimensions — sensor with Fig. 6: Dimensions — sensor without NPT 3/4″ screw-in adapter screw-in adapter V02.00 | 2022/08 | 8 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 9: Display And Control Elements
If the flow rate increases, the switching status changes when the switching point is undershot by the hysteresis. V02.00 | 2022/08 | 9 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 10: Temperature Monitoring
The device parameters can be set via IO-Link and then operated at the digital inputs with the appropriate settings in SIO mode. Not all functions and properties of the device can be used in SIO mode. V02.00 | 2022/08 | 10 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 11: Technical Accessories
FS…, FP… product series; M18 x 1.5 11 37 material: stainless steel N3/4“ 14.5 1.4571 (316Ti); process connection: N3/4″ V02.00 | 2022/08 | 11 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 12: Installing
Prevent the tip of the probe rod coming into contact with the opposite side of the flow channel inner wall. V02.00 | 2022/08 | 12 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 13: Special Installation Instructions
(replacement seal included in the delivery). „ After removing and reinstalling the sensor, teach in new teach-in values. V02.00 | 2022/08 | 13 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 14: Connecting
PNP/NPN 2 out 2 3 L– out 1: Flow, IO-Link out 2: Temperature Fig. 11: Pin assignment Fig. 12: FS100-…-2UPN8-H1141 wiring diagram V02.00 | 2022/08 | 14 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 15: Commissioning
After the warm-up phase, the device is ready for use and automatically switches to display mode for the flow speed. V02.00 | 2022/08 | 15 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 16: Operation
NC switching output: Switching point exceeded (LOW level) Yellow Device locked Yellow "Lock/unlock" process active flashing Device unlocked Error, see "LED Indicators — diagnostic Messages" V02.00 | 2022/08 | 16 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 17: Led Indicator Bar - Flow Monitoring
Yellow LED: Indicates the set switching point proportional to the indicated range. Temperature below the switching point: Temperature above the switching point: V02.00 | 2022/08 | 17 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 18: Leds - Diagnostic Messages
– Short circuit at transistor flashing output Out1 – – – General error (shut down all outputs, manual reset required) V02.00 | 2022/08 | 18 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 19: Setting
The Automatic detection func- tion is active by default. The output can also be set selectively as required via the IO-Link inter- face. V02.00 | 2022/08 | 19 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 20: Setting Via Touchpads
Reset to last setting settings Reset to factory setting Change FLOW output over to NO/NC Change TEMP output over to NO/NC V02.00 | 2022/08 | 20 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... - Page 21 ENTER NO/NC NO/NC Save MODE Temp Set Temp ENTER NO/NC NO/NC Save MODE Fig. 13: Setting via touchpads — flow chart V02.00 | 2022/08 | 21 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
-
Page 22: Quick-Teach - Setting The Current Flow Speed As The Switching Point
Reduce the switching point incrementally by 9.1 %: Press [MODE]. Store the switching point: „ Press [Enter]. LED bar briefly flashes green twice. V02.00 | 2022/08 | 22 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 23: Max/Min Teach-In - Setting The Indicated Range For Flow
„ Store the lower limit value: Press [ENTER]. LED bar briefly flashes green twice. The next menu appears. V02.00 | 2022/08 | 23 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 24: Setting The Switching Point For Temperature
To exit advanced settings: „ Automatically: Do not press the touchpads for at least 30 s. „ Manually: Press [MODE] + [SET] simultaneously once. V02.00 | 2022/08 | 24 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... - Page 25 „ Save settings: Press [ENTER]. ð LED bar briefly flashes green twice. The next menu appears. V02.00 | 2022/08 | 25 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
- Page 26 ð LEDs 5…7 off (NO) „ Save the output function: Press [Enter]. ð LED bar briefly flashes green twice. The next menu appears. V02.00 | 2022/08 | 26 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
-
Page 27: Setting Via Io-Link
In SIO mode, the device operates in accordance with the most recent setting configured in IO-Link mode. V02.00 | 2022/08 | 27 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 28: Troubleshooting
If no faults are identified, this indicates that the device is faulty. In this case, decommission the device and replace it with a new device of the same type. V02.00 | 2022/08 | 28 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 29: Maintenance
Observe our return acceptance conditions when returning the device to Turck. 12.1 Returning devices Returns to Turck can only be accepted if the device has been equipped with a Decontamination declaration enclosed. The decontamination declaration can be downloaded from https://www.turck.de/en/retoure-service-6079.php and must be completely filled in, and affixed securely and weather-proof to the outside of the packaging. -
Page 30: Technical Data
Stainless steel, 1.4571 (316Ti), FKM O-ring, AFM flat seal (only for devices with a G…″ process connection) Electrical connection Connector device: Male connector, M12 × 1, 4-pin V02.00 | 2022/08 | 30 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... - Page 31 LEDs indicate the status of the power supply, outputs and teach-in processes, display of the process values via LED bar V02.00 | 2022/08 | 31 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
-
Page 32: Turck Subsidiaries - Contact Information
Via San Domenico 5, IT-20008 Bareggio (MI) www.turckbanner.it Japan TURCK Japan Corporation ISM Akihabara 1F, 1-24-2, Taito, Taito-ku, 110-0016 Tokyo www.turck.jp V02.00 | 2022/08 | 32 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... - Page 33 Inönü mah. Kayisdagi c., Yesil Konak Evleri No: 178, A Blok D:4, 34755 Kadiköy/ Istanbul www.turck.com.tr Turck Inc. 3000 Campus Drive, USA-MN 55441 Minneapolis www.turck.us V02.00 | 2022/08 | 33 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
- Page 34 Over 30 subsidiaries and 60 representations worldwide! 100002085 | 2022/08 100002085 www.turck.com...
Need help?
Do you have a question about the FS100 L Series and is the answer not in the manual?
Questions and answers