Connect Programming Cable - Rabbit RabbitCore RCM3000 Getting Started Manual

2.3.2 Connect Programming Cable

The programming cable connects the RCM3000 module to the PC running Dynamic C to
download programs and to monitor the RabbitCore module for debugging.
Connect the 10-pin connector of the programming cable labeled
the RCM3000 module as shown in Figure 4. Be sure to orient the marked (usually red)
edge of the cable towards pin 1 of the connector. (Do not use the
used for a normal serial connection.)
NOTE: Be sure to use the programming cable supplied with this Development Kit—the
programming cable has red shrink wrap around the RS-232 converter section located in
the middle of the cable. Programming cables with clear shrink wrap from other Z-World
or Rabbit Semiconductor kits were not designed to work with RCM3000 modules.
RN1
GND NC PD1 PD0
GND +3.3V PD7 PD6
VBAT
VRAM PD3 PD2
EXT
/RES
SM1 PD5 PD4
IN
SM0 /IORD PG3 PG2
/IOWR PG4 PG1 PG0
PG5 PG6 PD4 PD5
PC5
PG7 PE0 PC4
PC3
PE1 PE3 PC2
PC1
PE4 PE5 PC0
PE6 PF0 PF1
PE7
PF7 PF6 PF2 PF3
PF5 PF4 PA0 PA1
PB7 PB6 PA2 PA3
PB5 PB4 PA4 PA5
PB3 PB2 PA6 PA7
PB0 /RES PE4 GND
J1 J3
C1
R1
R4
R3
C3
R5
R2
RC13
RC12
R21
RC10
RC11
GND NC PD1 PD0
GND +3.3V PD7 PD6
VBAT
VRAM PD3 PD2
EXT
/RES
SM1 PD5 PD4
IN
SM0 /IORD PG3 PG2
/IOWR PG4 PG1
PG0
PG5 PG6 PD4
PD5
PG7 PE0 PC5 PC4
PE1 PE3 PC3 PC2
PE4 PE5 PC1 PC0
PE6 PE7 PF0 PF1
PF7 PF6 PF2 PF3
PF5 PF4 PA0 PA1
PB7 PB6 PA2 PA3
RCM2JA
PB5 PB4 PA4 PA5
PB3 PB2 PA6 PA7
PB0 /RES STATUS GND
J4
Figure 4. Connect Programming Cable to RCM3000
Connect the other end of the programming cable to a COM port on your PC.
NOTE: Some PCs now come equipped only with a USB port. It may be possible to use
an RS-232/USB converter with the programming cable supplied with your RCM3000
module. An RS-232/USB converter is available through the Z-World Web store.
12
RCM1JA RCM1JB
GND
RCM3000 ETHERNET CORE MODULE
J15
SLAVE
UX10
MASTER
UX11
RC15 RCM2
RC24
RC19
RC20
RC23
UX9
RC14
RC17 RC22
RC16
UX3
RC21
RC2
UX2
+3.3V
R14
U1
C5
C8
RCM2JB
C6
RESET
S2 S3
RxC TxC
C7
J5
RS-232
TxB RxB GND
RN5
R20
R17
U4
+5V
Battery
+3.3V
BT1
GND GND
GND
+5V
+3.3V
J8
+3.3V +3.3V
+5V
+5V
RC6
RC7
C16
U6
C9
U3
UX5
RC9
UX7
Colored
RCM30/31/32XX SERIES
PROTOTYPING BOARD
shrink wrap
PG6 PG7
Colored edge
J10
DS2 DISPLAY BOARD
DS1
Programming Cable
to header J1 on
PROG
connector, which is
DIAG
L1
C17
J11
D1
C13
2.5 MM JACK
D2 GND +DC
C12
U5
+5V
+3.3V
GND
+5V
UX4
RC25
RC4
RC5
DISPLAY BOARD
C14
RC27
To
U3
RC28
RC29
RC26
PC COM port
UX13
J7
DISPLAY BOARD
RabbitCore RCM3000