Savant PAV-VIMAP8S Quick Reference Manual page 2

Rear Panel
A B C D
1 2 3 4
HDMI HDMI HDMI HDMI
In In In In
Rx Tx Rx Tx Rx Tx Rx Tx
10 10 10 10
GbE GbE GbE GbE
1 1 1 1
GbE GbE GbE GbE
RS232 RS232 RS232 RS232
IR IR IR IR
Rx Rx Rx Rx
Tx Out Tx Out Tx Out Tx Out
G G G G G G G G
P1 P1 P1 P1
P2 P2 P2 P2
F G H
Item Description
1G of reserved network data bandwidth.
Commonly used to connect any network
compliant device to transmit its data onto the
Ethernet network by sharing the 10G network
link. 8-Pin RJ-45 female connection.
1 Gigabit
A
IMPORTANT NOTES:
Ethernet
– Do not connect these ports to a network
switch.
– This is a courtesy port. It will not work for all
network functions. For example, Spanning
tree devices are not supported by this port.
SFP+ Housing; Used for connectivity to the 10G
Ethernet Network Switch.
10 Gigabit IMPORTANT! For all 10G connections, use only
B
Ethernet Savant certified SFP+ Direct-Attach Copper
(DAC) cables, or Savant certified fiber and fiber
connectors along with Savant certified SFP+
modules.
Rx – Link Activity LED indicator for all data
Rx/Tx LEDs received on the 10G connection
C
(10 GbE) Tx – Link Activity LED indicator for all data
transmitted from the 10G connection
19-Pin Type A HDMI female digital audio/video
input.
D
HDMI In Supports HDMI 2.0a
HDMI 2.0 compliant cable is required for 4K
content.
100-240V AC 5A 50/60Hz power input module
with On/Off switch.
I – Applies power to the device.
O – Removes power to the device.
Power Input
E
Module
NOTE: Includes a field replaceable 5A 250V Fast
acting fuse. For replacement information see
Video over IP Deployment Guide
Customer
RS232 – 3-pin Screw down plug-in connection.
Transmits and receives serial data to and
RS-232
F
from serial controllable devices. For pin-out
Control Port
information, refer to the RS-232 Wiring section
below.
IR - 3-pin Screw down plug-in connection.
Transmits IR signals via an IR Flasher
IR Control
G
(5V tolerant) to devices with an IR input or IR
Port
receiver. For pin-out information, refer to the IR
Wiring section below.
H
Push Buttons Push buttons – Reserved for future use.
8-Pin RJ-45 female connection. Used to
communicate with the Savant System Host.
I
Ethernet
Supports Audio Video Bridging (AVB)/Time
Sensitive Networking (TSN).
J
Grounding Chassis Ground (optional)
Savant Video Input UP Transmitter QRG | 009-1604-02
Copyright 2021 Savant Systems, Inc. | 210127
5 6 7 8
Serial Number
HDMI HDMI HDMI HDMI
In In In In
HIPOT
Rx Tx Rx Tx Rx Tx Rx Tx
100 - 240 V ~
10 10 10 10
50/60 Hz
GbE GbE GbE GbE Max Current: 5A
Fuse: 250V, 5A
Fast Acting
1 1 1 1
GbE GbE GbE GbE
Compliance
RS232 RS232 RS232 RS232
IR IR IR IR
Rx Rx Rx Rx
Tx Out Tx Out Tx Out Tx Out
G G G G G G G G
P1 P1 P1 P1
P2 P2 P2 P2
on the Savant
Community.
Wiring and Connections
The following is a description of connections that can be made to the
E
Audio/Video over IP Switch:
IR Wiring
IR connections are made using a 3-pin
Control Connector supplied with the device.
The wire slips into the hole and locks with a
screw located at the top of the connector.
IMPORTANT: IR Wiring Precautions
Ethernet
Ensure that all IR emitters are within 15 feet
(4.6 meters) from the controller's location.
Use of 3rd party blinking IR emitters with
I J
Talk Back is not recommended. These types of emitters can draw
voltage away from the IR signal that can degrade IR performance.
RS-232 Wiring
Serial control connections are made using
a 3-pin Control Connector supplied with
the device. The wire slips into the hole and
locks with a screw located at the top of the
connector.
SFP+ 10 GbE
Enhanced small form-factor pluggable connection. Use
a Savant certified Direct Access Copper (DAC) SFP+
cable to connect the chassis to the 10G switch, or Savant
certified fiber and fiber connectors along with Savant
certified SFP+ modules.
Transport Distance
DAC cable
OM3 multi-mode Fiber
Installation
The Savant Audio/Video over IP 8-Port / 4-port Transmitter chassis
can be mounted using the included rack mounting ears and hardware
in a 3U rack style enclosure and is compatible with all standard 19-inch
National Electrical Manufacturers Association (NEMA) rack mounts.
For more information see the
on the Savant Customer
Network Requirements
For more information, see the
the Savant Customer
Additional Information
Refer to the following documents located on the
Community for additional information.
– Savant Video over IP Deployment Guide (009-1551-xx)
– Savant Video over IP Network Configuration Guide (009-1552-xx)
– Savant IP Audio Deployment Guide (009-1571-xx)
2 of 2
Out
G
PIN 1
PIN 2
PIN 3
Rx
Tx
G
PIN 1
PIN 2
PIN 3
6 ft (2 m)
1000ft (300 m)
Savant Video over IP Deployment Guide
Community.
Savant Device Networking Guidelines
Community.
Savant Customer
45 Perseverance Way, Hyannis, MA 02601
Savant.com
1
2
3
Not Used
IR +
IR -
1
2
3
Receive
Transmit
Ground
on
| 508.683.2500