JVC XL-R5010BKC Instructions Manual page 30

1
Select and stop the CD to be recorded.
Example: To record the CD loaded in tray CD1.
• Only the selected CD is recorded.
2
Load a recordable CD-R or CD-RW disc into the
CDR and close the tray.
• The disc is read if required.
3
Press the CD REC button (main unit/remote
control) to start recording. "DISC DUBBING" is
shown in the information display
• When a blank disc is in the CDR tray, "UPDATE OPC" is
shown following "DISC DUBBING".
When "ADD FINALIZE?" is shown in the information
window:
• No response (no input) assumes that finalization is to be per-
formed, or you can press the SET button (main unit/remote con-
trol) to confirm that finalization is to be done. Press the
CANCEL button (main unit/remote control) to keep the disc
unfinalized.
Note
• This message will not be shown if the menu FINALIZE func-
tion setting is "OFF". The default setting is "ON".
The 3-CD changer and CDR start simultaneously. (This is
called synchronized recording)
• Recording starts from the first track of the CD.
Remaining play time of
track being recorded
CD PLAYER 1 2 3 4 5
6 7 8 9 10
CD REC CD
• When a digital CD is recorded, its signals are recorded in their
original form. Track marks are inserted automatically where
one track changes to the next and track numbers change accord-
ingly.
When the recording of the last song in the CD is
complete, "STOP DUBBING" flashes and recording
automatically stops.
When recorded without canceling "ADD FINALIZE?"
"FINALIZE" is shown in the information window after recording
is stopped and finalization is automatically performed.
Checking a track number during recording
Press the DISPLAY button on the remote control.
Remote Control
DISPLAY
Disc source Track number
24
STOP
Remaining recording time on
CD-R or CD-RW
SYNCHRO
HIGH SPEED AUTO TRACK
DIGITAL REC
CD-R
44.1 L
kHz
– 40 30 20 15 10 6 3 0 dB
R
CD-R or CD-RW
track number
To stop the recording at any time
Press the CDR or CD Control STOP 7 button on the main unit or
the 7 (stop) button on the remote control. "STOP DUBBING"
flashes in the information display, and the unit stops recording.
Notes
• There is no need to adjust the recording level when recording a
digital signal.
• If the source CD being recorded from the 3-CD changer is itself
a first-generation digital copy, digital recording cannot be per-
formed. When this occurs, the recording type will switch from
digital to analog automatically.
• This type of recording cannot be started during CD playback. It
must start from the beginning of the first track of the CD.
• When the CD REC button is pressed, the function is automati-
cally switched to CD. This means that when the CD to be
recorded has been selected, recording can proceed straightaway.
• Upon completion of recording, "STOP DUBBING" flashes in
the information display. Always wait for the "STOP DUB-
BING" message to be cleared before proceeding with the next
operation.
• When you try to eject the disc from the CDR tray, "FINAL-
IZE?" is shown in the information display when recording onto
an unfinalized disc. To finalize the disc, press either the SET or
FINALIZE button (main unit/remote control). To skip the final-
ization process, press the EJECT 0 button one more time or the
CANCEL button (main unit/remote control).
• Depending on the disc, the entire CD may not be recorded. In
such a case, use the 1 Disc Dubbing feature (see page 25) to
record.
Performing synchronized one-button recording of
a single track
STANDBY
STANDBY/ON
3 - CD
PHONES LEVEL
PLAY & EXCHANGE
MIN MAX
PLAY MODE CD EDIT CD REC
STOP PLAY PAUSE
PHONES
7
3
1
CD1 CD2
3
CD REC CD EDIT
1
4
7
10
PLAY
MODE REPEAT
•
REC
REC MUTING
7
RM–SXLR5010A
1 2
MULTI JOG
REC LEVEL
–
EJECT
REC SOURCE SELECTOR MIX BLANCE
DIGITAL CD LINE MIC
LINE CD
MIC LINE
SYNCHRO MENU SET CANCEL
REC/
FINALIZE STOP PLAY PAUSE REC MUTING
MIC
STANDBY/ON
CD3
FINALIZE DISPLAY
2 3
5 6
8 9
+10
C O N T R O L
CD CDR
FADE SYNCHRO
+
PITCH
SET
PITCH–
REMOTE CONTROL
+