Bpa650, Bpa800, Bpa1200: Connect The Internet Gateway (Optional Accessory 828Ev); Bpa650, Bpa800, Bpa1200: Special Features (Optional Accessory) - BPA BPA500 Assembly And Operating Instructions Manual

NOTE: Only the original remote controls from the manufacturer should
be used. Remote controls that may look very similar, but do not
originate from the manufacturer are not compatible. Such third-party
remotes create malfunctions such as automatic opening, and the
guarantee on the function and safety expires.
BPA650, BPA800, BPA1200: Connect the Internet
29
Gateway
(Optional accessory 828EV)
Before starting you MUST have:
• a router
• active internet connection
• a free "Ethernet" terminal on your router
• internet gateway serial number (on the backside of the device)
• a pair of photocells connected to the garage door opener. If there are
no photocells connected the garage door can only be opened.
WARNING!
To prevent possible SERIOUS INJURY or DEATH:
• When the Internet Gateway is used with a garage door opener, the
opener MUST ONLY be installed with sectional doors.
• Never allow children playing with the garage door, the remote control,
wall-switches or any other accessories.
• Operate the garage door only when it is technically faultless and the
door area is free of obstructions or people.
• This product allows operating the garage door without visual control.
• Therefore the door may execute unexpected travels. Never pass
through a closing garage door.
• For resindential use only. Only instructed poeple may use this
• product.
• Some parts of the car (doors, trunk lids) may extend into the travel
path and cause serious damage to the garage door and/or the car.
• The serial number on the backside of this device is for your personal
use only. Save this numer from others.
1. Connect
Connect the provided ethernet cable (1) to router (2). Use the plug valid
for your country ( not all models). Connect power (3) to the internet
gateway (4). When the internet gateway connects to the internet, the
green light (5) will stop blinking and will light solid.
2. Create an account
Download the myQ App on the App Store or Google Play. Go to "Regis-
ter" and create an account. If you already have an account, use your
username and password.
3. Register the internet gateway
Enter the Serial Number located on the bottom of the internet gateway
when prompted.
4. Add MyQ devices
Use an internet enabled computer, tablet or smartphone to add devices.
Follow the instructions on the app.
Note: After you add a device, the blue light on the internet gateway will
appear and stay on.
5. Test
After having installed and registered correctly you may now test the
foolowing features:
• open and close the garage door
• status request DOOR OPEN or DOOR CLOSED
Need Help?
Visit www.bpa.industries
BPA650, BPA800, BPA1200: Special Features
30
(Optional accessory)
A. Door within a door connection
Description of feature:
Locate auxiliary quick connect terminals. Remove wire bridge.
Insert bell wire into quick connect terminals 4 and 5.
B. Flashing light connection
Description of feature:
The flashing light can be installed anywhere. Connect light leads to
quick connect terminals 6 and 7.
C. Partial opening feature
Description of feature:
The pedestrian , ventilation or pet opening position is an adjusta-
ble second stop position between the fully opened and fully closed
position of the garage door.
Activate:
NOTE: Any time programming requires pushing two buttons simul-
taneously, make sure this is executed accurately. If other buttons
than described will flash, briefly cut operator from current and start
rogramming from the beginning.
1. Move the door into to the desired partial opening position
using the remote control or wallcontrol.
2. Choose a non programmed button on your remote control.
3. Push square button and UP button simultaneously for 3
seconds and wait for the operator light to flash. Then push
the remote control button. To program an additional remote
control start again with step1.
Deactivate:
1. Move the door to the fully closed position.
2. Push square button and UP button simultaneously for 3
seconds and wait for the operator light to flash.
en 8