Hang Opener; Mounting Door Bracket; Attaching Door Arm On The Trolley; Electrical Connection - BPA BPA500 Assembly And Operating Instructions Manual

15

Hang opener

Fully open the door, put down door opener on the door (Fig. A).
Lay a piece of wood / cardboard on the marked spot (X).
The opener must be securely fastened to a structural support of the
garage.
Three representative installations are shown (Fig. B). Yours may be
different. Hanging brackets (11) should be angled to provide
rigid support. On finished ceilings, attach support bracket(not delivered)
to a self-supporting structio-nal element before installing the opener. For
concrete ceiling mount, use concrete anchors (22) provided.
On each side of opener measure the distance from the opener to the
structural support (or ceiling). Cut both pieces of the hanging bracket to
required lengths. Flatten one end of each bracket and bend or twist to fit
the fastening angles. Do not bend at the bracket holes. Drill 4,5mm pilot
holes in the structural supports (or ceiling). Attach brackets to supports
with wood screws (20).
Lift opener and fasten to hanging brackets with screw (16) and nut (17).
Check to make sure rail is centered over the door.
Remove piece of wood / cardboard. Operate door manually.
If door hits the rail, raise header bracket.
After the installation of the garage door drive, particularly using a rail
extension, if the rail is observed to be bent up or down for more than 5
cm during the beginning or end of the travel as well as while encounte-
ring an obstacle, a central suspension must be provided by the custo-
mer. For this, please contact the manufacturer of the garage door drive.
Pay attention to a horizontal course of the rail along the
ceiling.The distance can be adjusted by the given hole spa-
cing. Protruding ends of the ceiling fixture can be reduced if
necessary.
16

Mounting door bracket

Installation in sectional or one-piece doors:
The door bracket (6) has multiple mounting holes. Attach door bracket
top centre on the inside of the door as shown. Mark holes and screw
door bracket.
1. One-piece or sectional door with a guide rail:
distance to door top edge 0-100 mm.
2. Sectional door with two guide rails:
distance to door top edge 100-130 mm.
NOTE: The attachment point on the door must be the frame or a stable
place on the door panel. If necessary, drill through and screw (not inclu-
ded) together as shown in Fig. B.
17

Attaching door arm on the trolley

The straight door arm is already pre-assembled.
Recommended installation:
The trolley can be separated from the drive by pulling the red handle
and manually pushing towards the door. When the door is closed,
fix the curved door arm (8) on the door bracket with the bolt (18) and
secure with cotter pin (19). Connect straight and curved door arms
together flush with an overlap of 2 holes with screw (16) and secure
with nut (17). Choose the holes in such a way that the door arm
stands at an angle of about 30-40°.
Mount the release handle of the emergency release at a
height less than1.80 m. Attach the yellow label regarding the
release of the garage door opener (sticker) on the cord of the
door handle.
18

Electrical connection

In order to avoid personal injury and damage to the device,
the door opener should be operated only if such an inst-
ruction is explicitly stated in this manual. The power plug
must always be accessible for the purpose of disconnecting the mains
supply. Electrical installations may only be undertaken by an authorized
electrician.
19 BPA650, BPA800, BPA1200: Install illuminated
push button or Multi-function door control
(Optional accessory)
Locate door control where the garage door is visible, away from door
and door hardware and out of the reach of children. Mount at least 1,5
m (5 feet) above the floor. Permanently fasten the caution label perman-
ently to the wall near the door control as a reminder of safe operating
procedures. There are 2 terminals on the back of the door control.
Strip about 6mm of insulation from bell wire. Separate wires enough to
connect the white/red wire to RED terminal screw and the white wire to
WHT terminal screw. Fasten the door control to an inside garage wall
with sheet metal screws provided. Drill 4mm holes and use anchors if
installing into drywall. A convenient place is beside the service door and
out of reach of children. Run the bell wire up the wall and across the
ceiling to the garage door opener. Use insulated staples to secure wire.
Operation of the Door Control:
Press to open or close the door. Press again to stop the door while
moving.
en 5