Table of Contents
Advertisement
Available languages
Available languages
2
Intended use
The device is intended for the opening and closing of garage doors
(please refer to section 6 "Door Types"). The device is not meant for commer-
cial use but solely for the use in private garage doors that are appropriate for
a single household. Any improper use of the drive could increase the risk of
accidents. The manufacturer assumes no liability for such usage. Only the ori-
ginal accessories may be connected to the drive. With this drive, automated
gates must comply with the currently valid international and country-specific
standards, guidelines and regulations (among other things, EN 13241, EN
12453 and EN 12604).
3
Scope of supply
Please check the supplied parts for completeness before starting the in-
stallation. Note: The numbering only applies to the corresponding section.
Parts overview:
1.
Drive head
2.
Remote control
3.
Rail bracket
4.
Hardwarebag
5.
Header bracket *
6.
Door bracket
7.
Adapter for gear wheel *
Hardwarebag:
Truss head screw
14.
6 x 80 mm
15.
Lock nut M6
16.
Hexagonal head screw
17.
Nut M6
18.
Bolt
4
Product overview
This figure always offers you a complete overview of the readyassem-
bled system during the step by step installation of the system.
a.
Header bracket
b.
Belt
c.
Rail
d.
Carriage
e.
Connecting piece
f.
Rail bracket
g.
Hanging bracket
1x
8.
Curved door arm 45° *
2x
9.
Curved door arm 90° (BPA1200)
2x
10.
C-bracket *
1x
11.
Hanging bracket
Wireless Wall Control
1x
12.
(BPA650-1200)
1x
13.
Rail 8323CR5 (BPA500)
1x
* Delivery with the rail
1x
19.
Safety cotter pin
1x
20.
Screw ST 6,3 x 50 mm
6x
21.
Screw ST 6,3 x 18 mm
6x
22.
Plug
1x
h.
Power cable
i.
Drive head
j.
Release
k.
Straight door arm
l.
Curved door arm
m.
Door bracket
5
Before you begin
IMPORTANT NOTE
If your garage does not have a side entrance, an external emergency
release should be installed. This allows for manual operation of the
garage door from the outside during power failure.
6
Door Types
A.
One-Piece Door with Horizontal Track Only.
B.
One-Piece Door with Horizontal and Vertical Track – Canopy door
arm and photo cells required. See your dealer.
C.
Sectional Door with Curved Track – connect door arm.
D.
Canopy door arm and photo cells required. See your dealer.
E.
Canopy door arm for use on door types B and D.
Note: The system BPA500 cannot be used for one-piece garage doors
with horizontal and vertical guide rails and two-wing doors.
7
Preparation
1x
1x
First, check whether your door is balanced and in equilibrium.
2x
Open your door about halfway and let it go.
2x
The door can now hardly change its position independently,
1x
but must remain in this position held by the spring force alone.
1x
1.
The rail of the garage door MUST be connected securely and firm-
ly to the supporting wall or ceiling above the garage door.
2.
Additional brackets and mounting rails (not included in the supply)
might be required, if the your garage ceiling has a cladding, boards
or similar.
1x
3.
If your garage does not have a separate side entrance, an external
emergency release (refer to section "Optional Accessories") must
6x
be installed.
8x
8
Tools required
6x
Tool list:
Ladder
Marking pen
Pliers
Drilling machine
Hammer
Ratchet 10 mm / 13 mm
Hacksaw
Different drill bits for concrete
and(or wood (8, 6, 5, 4.5 mm)
Box wrench
Water level
Screwdriver
Measuring tape
en 3
Hide quick links:
Advertisement
Chapters
Table of Contents
