Table of Contents
Advertisement
Quick Links
135756312 Gun FStart P Compliant HVLP-12-XLva
135756315 Gun FStart P Compliant HVLP-15-XLva
135756318 Gun FStart P Compliant HVLP-18-XLva
135756412 Gun FStart P CONV-12-XLva
135756415 Gun FStart P CONV-15-XLva
135756418 Gun FStart P CONV-18-XLva
135756712 Gun FStart P Compliant LVLP-12-XLva
135756713 Gun FStart P Compliant LVLP-13-XLva
135756715 Gun FStart P Compliant LVLP-15-XLva
135756718 Gun FStart P Compliant LVLP-18-XLva
Translation from the original manual - Index C
FStart Pressure / Suction
II 2G Ex h IIB T6 Gb X
582120110-US
SAMES KREMLIN SAS
13 Chemin de Malacher
38240 Meylan
Tél.: 33 (0)4 76 41 60 60
www.sames-kremlin.com
135756515 Gun FStart S CONV-15-Mva
135756518 Gun FStart S CONV-18-Mva
Advertisement
Table of Contents
Related Manuals for SAMES KREMLIN FStart P Compliant HVLP-12-XLva
Summary of Contents for SAMES KREMLIN FStart P Compliant HVLP-12-XLva
- Page 1 FStart Pressure / Suction 135756312 Gun FStart P Compliant HVLP-12-XLva 135756515 Gun FStart S CONV-15-Mva 135756315 Gun FStart P Compliant HVLP-15-XLva 135756518 Gun FStart S CONV-18-Mva 135756318 Gun FStart P Compliant HVLP-18-XLva 135756412 Gun FStart P CONV-12-XLva 135756415 Gun FStart P CONV-15-XLva...
-
Page 2: Table Of Contents
Any communication or reproduction of this document, in any form whatsoever, and any exploitation or communications of its contents are prohibited, except with the express written permission of SAMES KREMLIN. The descriptions and characteristics contained in this document are subject to change without prior notice. © SAMES KREMLIN 2020... -
Page 3: Safety
• With regard to the fluids and paints used with its equipment, SAMES KREMLIN cannot be held responsible for direct or indirect material damage caused in use, for the poor compatibility of the materials in contact, for the inherent risks to personnel and the environnment, for wear and tear, for malfunctions of the equipment or installations and for the quality of the finished product. - Page 4 • It is imperative that the spray booths are properly ventilated to Ventilation prevent any high concentration of fluid or paint and maintain it lower than the LEL (Lower Explosion Limit). • If ventilation is shut off, toxic substances or contamination may remain in the spray booth and cause a risk of fire, poisoning or irritation.
- Page 5 • In order to prevent the accumulation of electrostatic charges which could generate an electric arc in a flammable or explosive environment, it is necessary that all conductive components of the system are grounded. • The gun must be ‘grounded’ via the fluid hose or the air hose. •...
- Page 6 • Parts and accessories must only be supplied or approved by SAMES KREMLIN. Equipment • SAMES KREMLIN cannot be held responsible for personal injury as modification well as breakdowns and/or damage resulting from modifications to the equipment. • Any modification of equipment made by the user and not authorized by SAMES KREMLIN will result in loss of certification.
-
Page 7: Declaration
Declaration Refer to the declaration delivered with the equipment. Identification of the product Description of FStart Pressure / Suction Guns recommended to spray varnishes, lacquers, shades, polyurethanes. Description of the ATEX / UKCA marking • Each device is marked with the name of the manufacturer, the reference of the device and important information for the use of the device (air pressure, electrical power,etc.). - Page 8 Description Manufacturer trademark SAMES KREMLIN logo Gun model FStart Pressure / Suction CE : European conformity : For use in explosive area II : group II 2 : class 2 Surface equipment meant to an area where explosive II 2 G atmospheres due to gas, vapours, mists are liable to appear from time to time in usual operating.
-
Page 9: Technical Data
Technical data FSTART P CONV FSTART P HVLP FSTART P LVLP FSTART S CONV Pressure Suction Version Maximum air supply 6 bar / 87 psi pressure (network) Maximum fluid supply 6 bar / 87 psi pressure Product M 3/8 NPS supply Air flow rate 22.1m3/h... -
Page 10: Fstart Pressure / Suction Materials
FStart Pressure / Suction materials Gun body Chrome die-cast aluminum Aircap Clear anodized aluminium Nozzle INOX (Stainless steel) Needle INOX (Stainless steel) Suction cup Aluminium Air and fluid connections Fittings mounted on the gun Air and fluid supply (depending on model) Air hose (anti-static quality) HVLP / LVLP : minimum ∅... -
Page 11: Installation
The 1 m / 39.37" distance indicated in the diagram is given for information purposes only and hold harmless to SAMES KREMLIN. The user is reponsible for the extracion and conditioning of the painting area where the equipment is used, for working... -
Page 12: Installation Diagram - Air Pressure Adjustment With Or Without Gauge At The Gun Handle
The 1 m / 39.37" distance may be modified if trials carried out by the user deem this necessary. • Using the grounding air hose, connect the gun to an air regulator that can supply at least 3 bar / 43.5 psi. •... -
Page 13: Storage
Storage Our equipment must be stored in its original packaging. In case of prolonged storage, it is preferable to carry out preventive maintenance for all lubricants before start-up. Storage before installation • Storage ambient temperature 0 / +50 °C (32° F / 122° F). •... -
Page 14: Gun Handling
10 Gun handling When assembling the aircap on the gun, hold it vertically in order to correctly align the aircap before screwing the aircap ring. Proper position Improper position • Keep the gun perpendicular to the surface to be painted. •... -
Page 15: Maintenance
Maintenance 11.1 Preventive maintenance Daily • Check groundings. • Clean the outside of the spray nozzle with a soft brush and solvent. • Flush the spray gun. • When the spraying system will not be used for an extended period of time, take off the nozzle and immerse it in s solvent filled container. -
Page 16: Assembly Errors
13 Assembly errors The use of improper replacement or defective parts may result in hazards to personnel, damage, malfunction or general shutdown of the equipment. 14 Troubleshooting Slightly unscrew the aircap retaining ring and rotate the aircap by one half turn. If the defect is reversed, one of the lateral air holes is plugged up or deformed. - Page 17 Trouble Cause Solution • Cut the pressure on • No fluid out of the gun Clogged nozzle the pump. Depressurize the hoses. • Remove and clean the nozzle with solvent by means of the brush. • Check the seal condition. •...
-
Page 18: Fstart Pressure / Suction Commercial References
15 FStart Pressure / Suction commercial references Principle of designation FStart HVLP XLva P=Pressure S=Suction HVLP (High volume, Low pressure) CONV (Conventional) Nozzle size: LVLP Aircap materialAircap material • (Low volume, Low pressure) 12 : 1.2 mm • 13 : 1.3 mm •... - Page 19 135756312 Gun FStart P Compliant HVLP-12-XLva 135756315 Gun FStart P Compliant HVLP-15-XLva 135756318 Gun FStart P Compliant HVLP-18-XLva 135756412 Gun FStart P CONV-12-XLva 135756415 Gun FStart P CONV-15-XLva FStart Pressure 135756418 Gun FStart P CONV-18-XLva 135756712 Gun FStart P Compliant LVLP-12-XLva...
-
Page 20: Available Projectors - References P/Ns
15.1 Available projectors – references P/Ns 131756112 Nozzle + Needle FStart HVLP-12 131756115 Nozzle + Needle FStart HVLP-15 131756118 Nozzle + Needle FStart HVLP-18 131756212 Nozzle + Needle FStart CONV-12 131756215 Nozzle + Needle FStart CONV-15 131756218 Nozzle + Needle FStart CONV-18 131756312 Nozzle + Needle FStart LVLP-12 Projectors... -
Page 21: Available Accessory - References P/Ns
15.2 Available accessory – references P/Ns 138400000 Aluminum suction cup Accessory Pack of 10 cup seals and 10 cover seals 138310320 for suction cup 15.3 Available packages – references P/Ns 152756420 Pack Airspray Lucky 2 ‘FStart P HVLP + Tank 2L’ 152756550 Pack Airspray Lucky 2 ‘FStart P CONV + Tank 2L’... -
Page 22: Maintenance Kit 129.756.902
16 Maintenance kit 129.756.902 16.1 Visual diagrams... -
Page 23: Parts List And Fstart Pressure / Suction Maintenance Kit (Spare Parts)
Maintenance kit FStart Pressure / Suction 129.756.902 composed of: Needle packing 129.756.903 Trigger set + air adjusters 129.756.905 Rear line assembly 129.756.904 16.2 Parts list and FStart Pressure / Suction maintenance kit (spare parts) Designation Quantity Included in maintenance kit Positions 129.756.902 Needle packing... -
Page 24: Dimensions Fstart Pressure / Suction
Accessory required for assembly / disassembly Designation Visual Wrench delivered with the FStart Pressure / Suction guns 17 Dimensions FStart Pressure / Suction Pressure Suction... -
Page 25: Warranty
SAMES KREMLIN only bears the cost of the parts needed to replace the defective material. No guarantee will be granted by SAMES KREMLIN for the following: - For defects and deteriorations resuslting from abnormal storage and / or storage conditions at the customer’s premises or for maintenance or use of the item that does... - Page 26 SAMES KREMLIN, nonché le normativ e nazionali e/o SAMES KREMLIN y a la normativ a nacional y /o local, preconizações de SAMES KREMLIN, bem como com locali, • •...
- Page 27 обору дов ание в theo các khuy ến nghị của SAMES KREMLIN cũng như 的 建 议 以 及 国 家 和 /或 地 方 法 规 ， 安 装 、 使 用 、 维 护 和 维 修 设 备 ，...
- Page 28 ﺑﯾﺎن اﻟﺗواﻓﻖ ﻣﻊ اﻻﺗﺣﺎد اﻷوروﺑﻲ AB UYGUNLUK BEYANI Le fabricant / The manufacturer / Der Hersteller SAMES KREMLIN SAS / El fabricante / Il produttore / O fabricante 13, chemin de Malacher / De fabrikant / Tillverkare / Valmistaja / Producent / Výrobce 38 240 - MEYLAN - FRANCE / Proizvajalec / Výrobca / Gyártó...
- Page 29 / Выполнено в Мейлане, на /发 布 于 Meylan, 时 间 / Được lập tại Meylan, vào / Meylanで行 わ れ た、オ ン / ﯾﺦ ر ﺑﺗﺎ ،ن ﻣﯾﻼ ﻓﻲ ت ﺗﺄﺳﺳ / Meylan'da yapıldı. 01/03/2021 - 03/01/2021 SAMES KREMLIN - 4 - N° : 578 146 130-2203.doc...
- Page 30 إﻋﻼن اﻟﻣطﺎﺑﻘﺔ ﻣن اﻟﻣﻣﻠﻛﺔ اﻟﻣﺗﺣدة İNGİLTERE UYGUNLUK BEYANI Le fabricant / The manufacturer / Der Hersteller SAMES KREMLIN SAS / El fabricante / Il produttore / O fabricante 13, chemin de Malacher / De fabrikant / Tillverkare / Valmistaja / Producent / Výrobce 38 240 - MEYLAN - FRANCE / Proizvajalec / Výrobca / Gyártó...
- Page 31 / Выполнено в Мейлане, на /发布于Meylan, 时间 / Được lập tại Meylan, vào / Meylanで行われた、オン / ﯾﺦ ر ﺑﺗﺎ ،ن ﻣﯾﻼ ﻓﻲ ت ﺗﺄﺳﺳ Meylan'da yapıldı. 01/03/2021 - 03/01/2021 SAMES KREMLIN - 6 - N° : 578 146 130-2203.doc...