Table of Contents
Advertisement
Quick Links
135756312 Gun FStart P HVLP-12-XLva
135756315 Gun FStart P HVLP-15-XLva
135756318 Gun FStart P HVLP-18-XLva
135756412 Gun FStart P CONV-12-XLva
135756415 Gun FStart P CONV-15-XLva
135756418 Gun FStart P CONV-18-XLva
Translation from the original manual - Index A
FSTART Pressure - Suction
II 2G Ex h IIB T6 X Gb
582120110
SAMES KREMLIN SAS
13 Chemin de Malacher
38240 Meylan
Phone: 33 (0)4 76 41 60 60
www.sames-kremlin.com
135756515 Gun FStart S CONV-15-Mva
135756518 Gun FStart S CONV-18-Mva
Advertisement
Table of Contents
Related Manuals for SAMES KREMLIN FSTART Pressure
Summary of Contents for SAMES KREMLIN FSTART Pressure
- Page 1 FSTART Pressure - Suction 135756312 Gun FStart P HVLP-12-XLva 135756515 Gun FStart S CONV-15-Mva 135756315 Gun FStart P HVLP-15-XLva 135756518 Gun FStart S CONV-18-Mva 135756318 Gun FStart P HVLP-18-XLva 135756412 Gun FStart P CONV-12-XLva 135756415 Gun FStart P CONV-15-XLva 135756418 Gun FStart P CONV-18-XLva...
-
Page 2: Table Of Contents
Table of Contents ........................2 Safety ............................3 Declaration ..........................7 Identification of the product ....................8 Description of FSTART Pressure - Suction ..............8 Description of the ATEX marking ................8 Technical data ........................9 Materials FSTART Pressure Suction ................9 Air and fluid connections .................. -
Page 3: Safety
• With regard to the fluids and paints used with its equipment, SAMES KREMLIN cannot be held responsible for direct or indirect material damage caused in use, for the poor compatibility of the materials in contact, for the inherent risks to personnel and the environment, for wear and tear, for malfunctions of the equipment or installations and for the quality of the finished product. - Page 4 • It is imperative that the spray booths are properly ventilated to prevent any high concentration of fluid or paint and maintain it lower Ventilation than the LEL (Lower Explosion Limit). • If ventilation is shut off, toxic substances or contamination may remain in the spray booth and cause a risk of fire, poisoning or irritation.
- Page 5 • In order to prevent the accumulation of electrostatic charges which could generate an electric arc in a flammable or explosive environment, necessary that conductive components of the system are grounded. • The gun must be 'grounded' via the fluid hose or the air hose. •...
- Page 6 • Parts and accessories must only be supplied or approved by SAMES KREMLIN. Equipment • SAMES KREMLIN cannot be held responsible for personal injury as modification well as breakdowns and/or damage resulting from modifications to the equipment. • Any modification of equipment made by the user and not...
-
Page 7: Declaration
• Environmental risks must be controlled as follows: Respect an average temperature of use of the equipment and products, which must be at least 5°C (41˚F), lower than the flash point of the products and within a range of 0 to 40°C (32˚ to 104˚... -
Page 8: Identification Of The Product
Identification of the product Description of FSTART Pressure - Suction Guns recommended to spray varnishes, lacquers, shades, polyurethanes. Description of the ATEX marking • Each device is marked with the name of the manufacturer, the reference of the device and important information for the use of the device (air pressure, electrical power, etc.). -
Page 9: Technical Data
Weight with cup 739g Weight without 402 g 401g 402 g Noise level 85 dBA 80.1dBA 83.9 dBA Materials FSTART Pressure Suction Gun body Chrome die-cast aluminum Head Clear anodized aluminum Nozzle INOX (Stainless Steel) Needle INOX (Stainless Steel Suction cup... -
Page 10: Nozzle Characterization Principle
The 1 m / 39.37" distance indicated in the diagram is given for information purposes only and hold harmless to SAMES KREMLIN. The user is responsible for the extraction and conditioning of the painting area where the equipment is used, for working... -
Page 11: Installation Diagram - Air Pressure Adjustment With Or Without Gauge At Gun Handle
Installation Diagram - Air pressure adjustment with or without gauge at gun handle 3 - P 1 : Pressure 4 - Guns, model measured at the FSTART Pressure- Suction gun handle during the operating (air needles open) 1 - P 0 : Air pressure... -
Page 12: Start-Up
Start-up • Assemble the head on the gun by positioning it according to the desired spray orientation. • Open at the maximum the air needle. • Open the fluid needle as far as it will go without a stop. • Connect the air hose. -
Page 13: Gun Handling
10 Gun handling When assembling the aircap on the gun, hold it vertically in order to correctly align the aircap before screwing the aircap ring. Keep the gun perpendicular to the surface to be painted. Avoid working with the wrist. Proper position •... -
Page 14: Maintenance
Maintenance 11.1 Preventive maintenance Daily • Check groundings. • Clean the outside of the spray nozzle with a soft brush and solvent. • Flush the spray gun. • When the spraying system will not be used for an extended period of time, take off the nozzle and immerse it in a solvent-filled container. -
Page 15: Assembly Errors
13 Assembly errors The use of improper replacement or defective parts may result in hazards to personnel, damage, malfunction or general shutdown of the equipment. 14 Troubleshooting Slightly unscrew the aircap retaining ring and rotate the aircap by one half turn. If the defect is reversed, one of the Distorted lateral air holes is plugged up or deformed. - Page 16 Trouble Cause Solution • • • No fluid out of the gun. Clogged nozzle Cut the pressure on the pump. Depressurize the hoses. • Remove and clean the nozzle with solvent by means of the brush. • Check the seal condition. •...
-
Page 17: Commercial References Fstart Pressure-Suction
15 Commercial references FStart Pressure-Suction Principle of designation FStart HVLP XLva P=Pressure S=Suction HVLP (High volume, low pressure) CONV (Conventional) Nozzle size: • 12 : 1.2 mm • 15 : 1.5 mm • 18 : 1.8 mm XLva Maximum fan width at 20 cm XL: >... -
Page 18: Available Projectors - References P/Ns
15.1 Available Projectors – references P/Ns 132756310 Aircap FStart P HVLP-12 18-XLva 131756112 Nozzle + Needle FStart HVLP-12 131756115 Nozzle + Needle FStart HVLP-15 131756118 Nozzle + Needle FStart HVLP-18 Projectors 132756410 Aircap FStart P CONV-12-XLva FStart P 131756212 Nozzle + Needle FStart CONV-12 132756420 Aircap FStart P CONV-15 18-XLva 131756215... -
Page 19: Maintenance Kit 129756902
16 Maintenance kit 129756902 16.1 Visual diagram Maintenance kit FSTART Suction Pressure 129756902 composed of Needle packing 129.756.903 Trigger set + Air adjusters 129.756.905 Rear line assembly 129.756.904... -
Page 20: Parts List And Fstart Maintenance Kit Pressure/Suction (Spare Parts)
Rear line Spring assembly Spring seat O-ring Spring Fluid adjustment screw O-ring seal Air cap ring Nozzle Gun body Fluid adjustment seat Needle set Fluid connector Air connector Accessory required for assembly/disassembly Designation Visual Wrench delivered with the FSTART Pressure –Suction... -
Page 21: Dimensions Fstart Pressure-Suction (Dimensions In Mm)
17 Dimensions FSTART Pressure-Suction (Dimensions in MM) Pressure Suction... -
Page 22: Warranty
"defective" item. The warranty given by SAMES KREMLIN is limited to the replacement of the item in its entirety or the partial replacement of the defective component. SAMES KREMLIN only bears the cost of the parts needed to replace the defective Material. - Page 23 SAMES KREMLIN, nonché le normative nazionali e/o reparar el equipo con arreglo a las recomendaciones reparação do equipamento de acordo com as locali, de SAMES KREMLIN y a la normativa nacional y/o preconizações de SAMES KREMLIN, bem como com • local, outros regulamentos nacionais e/ou locais aplicáveis,...
- Page 24 EU-MEGFELELŐSÉGI NYILATKOZAT DECLARAŢIA DE CONFORMITATE UE Le fabricant / The manufacturer / Der Hersteller SAMES KREMLIN SAS / El fabricante / Il produttore / O fabricante 13, chemin de Malacher / De fabrikant / Tillverkare / Valmistaja / Producent / Výrobce 38 240 - MEYLAN - FRANCE / Proizvajalec / Výrobca / Gyártó...
- Page 25 Utformat i Meylan, den / Meylan, Ranska, / Sporządzono w Meylan, dnia / Meylan, dnia / V Meylanu, / V Meylan dňa / Kelt Meylanban, / Întocmită la Meylan, pe data de 15/05/2019 - 05/15/2019 SAMES KREMLIN - 3 -...